Question about 2003 Honda CBR 954 RR Fireblade

1 Answer

Hi my bike was on my stand i started and accidently put the bike into first gear and it sytaled right away..and now its not turning over wen i try and start it, it makes a clicking sound but wont turn over?

Posted by a_tapping on


1 Answer

allan wadsworth

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 180 Answers

The bike must be in neutral when the kickstand is down or it will shut down. Its a safety feature.

Put the bike in neutral and it should fire right up.

If you can't get it out of gear, sit on the bike, put the kickstand up, pull the clutch in turn the key on and hit the start button, and it should fire right up.Make sure on/off button is on too.

If you tried that and it still clicks, check battery voltage, a low battery makes the solenoid click.
Make sure you have a clean battery terminals and tight terminals.
Check battery voltage. Most auto parts places will load test them for free.

If battery is good and it is in neutral and it still clicks, then the starter solenoid is bad.
replace the solenoid. And your bike should fire right up

Posted on Nov 30, 2010


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Bike cutting out

Do you have the kickstand up when you put it in gear? Many bikes have a lockout on the side stand to prevent you riding away with the stand down. Kills the engine instantly when placed in gear with the stand down.

Jul 21, 2014 | 1998 Honda XLR 125 R

2 Answers

2005 Boulevard c90 will die when put into gear?

Sounds like a kickstand safety switch that may be faulty or possibly unhooked, the best way too find out is to turn off your ignition of course then connect the two wires together, try starting your bike up and shift it into gear, If that works then you need too replace your stand switch, its not advised too run without your stand safety switch so replace it right away if it turns out faulty.

May 27, 2014 | 2005 Suzuki Boulevard C90

1 Answer

Stalls when bikes put in put in 1st. replaced my batt with a lithum ion one, starts up right away. Any ideas what's happening here and why?

You probably already checked this ... is your side stand down when the engine stalls? Many bikes have a safety interlock switch the kills the engine if the side stand is not in the proper stored position when the bike is put into gear.

Dec 08, 2012 | Ducati 749 S Motorcycles

2 Answers

When the FI light is on I can not start-up my Varadero 2003

I know this may sound daft but are you putting the kick stand away. My husband was in the garden for ages trying to get the Varadero to go but it was cutting out when put in gear. After closer inspection he had been leaving the kick stand down because he was used to his old bike and the stand sprang away by its self. He felt rather silly. I think it's worth a mention :-P

Dec 18, 2010 | 2003 Honda XL 1000 V Varadero

1 Answer

Runs without plugwires on shuts off when you put it in gear

Your cycle runs when you pull off one spark plug wire per cylinder. There are two spark plugs per cylinder and you did not remove both . Therefore you still have one spark plug on each cylinder firing to run the machine. Your motorcycle is also equipped with a side stand safety switch. Your bike will run on the side stand . But, if you put the bike in gear with the side stand down it is designed to turn off the motor. This is so you do not drive away with the stand down and loose control of the motorcycle on your first left hand turn. Get in the habit of putting your side stand up before putting the bike in gear and your problem is solved. Read your owners manual.

Oct 16, 2010 | 2003 Honda VT 750 C2 Shadow

2 Answers

I own a 2003 laverda 750S. I battle to get it started, the starter battles to turn the motor!!

how good is the battery check terminals are clean leads and all conections are good try remote battery and jump start it like a car if the problem goes away its your battery if not its the starter or solinoid or leads

Jun 23, 2010 | 1971 Laverda 750 S

1 Answer

'06 vtx 1300 c : engine dies when put into gear

You have one of two things going on. (1) You need to check the kick stand switch, your bike thinks the kick stand is still down. It may have been loosened out of adjustment by vibration. If the kick stand switch is out of whack, it will restart as long as the clutch in pulled in. But as soon as you try to let out the clutch it will kill the engine, if it is in gear. (2) Next problem could be, you need to loosen up the clutch cable a little bit, The clutch control on the handle bar has a screw type of adjuster (clutch cable passes through it ), try loosening it till it's easy for you to move the bike without the engine shutting off. Hope it helps and comment if you need more clarification.

May 08, 2010 | 2006 Honda VTX 1300 S

1 Answer

I've a yamaha yzf-r6. Problem- Lost all drive in any gear!!!??

It could actually be that the countershaft sprocket has stripped-out the splines that engage it to the countershaft. Take off the cover and have a look at the sprocket. Hopefully it is only the sprocket that is damaged and not the transmission shaft that it mounts to.
Another possibility is that the clutch cable has somehow gotten waaay out of adjustment. Just feel the clutch lever; you should have some free play at the lever. In other words, the first 1/4" or so of lever movement should do nothing except take up a small amount of slack in the cable.
Are you sure it is actually going into gear? Or have the splines on the shift shaft stripped-out? These are the things I would check first. If it isn't one of these, then I predict some major transmission work is in your future.

Jan 03, 2010 | 2003 Yamaha YZF-R6

1 Answer

Elecric start problem- kick start good

hi m8,, first try this, take the handle bar start button switch gear appart,,and clean the starter button terminals that connect wen u push button in,,spray some wd40 inside the switch gear wen u put it back together,,,,,often after off roading ,,connections that the eye cant see corrode wen the bike is washed down,, any probs still ,, shout and il anserw m8,,,,,cheers

Jan 08, 2009 | 2004 Yamaha WR 450 F

Not finding what you are looking for?
2003 Honda CBR 954 RR Fireblade Logo

361 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

6418 Answers


Level 3 Expert

85239 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

217 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides