Question about 1998 Cagiva Canyon 500

Open Question

Where can i find some spare parts for the cylinder head, gasket and cylinder rings CANYON 500 2000 thanks for your time

Posted by izzymexico on

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Oil on my spark plugs on my 2006 ford fusion


Hi,
If you've got oil on your spark plugs it's usually a sign of a cylinder-head gasket problem, or a piston rings problem.?
Neither of them are cheap to fix.
If you take it into the shop, they can do a compression test on each cylinder to see if there's a particular problem.
A good sign that it might be the head-gasket is getting water in the oil, which usually leaves a white/grey trace on the inside of the oil filler-cap.
If your engine has done a really high mileage, or it hasn't really been serviced properly, the rings are favourite.
You can't repair it, you can only do a major strip-down to replace the damaged parts.
Since it's a 12 year old car, I might be most economic to keep on running it as it is, for as long as it lasts & then junk it or sell it for spare parts.?
Best of luck.

Mar 09, 2018 | Ford Cars & Trucks

2 Answers

DIY question, compression test on 6cyl straight 6, if test show pressure way off on two or more cylinders is that a possibility of bad rings or may-be head bad?


If the cylinders are next to each other, very good probability that the head gasket failed between those cylinders. If the low pressure cylinders are not adjacent to each other, probably valves damaged or not seating. Usually, rings will all wear evenly (unless damage in a cylinder) and the compression will go down fairly evenly over all cylinders.

Feb 03, 2017 | Cars & Trucks

1 Answer

What parts are needed to replace piston rings while engine is in the car


Head Gasket
Rocker cover gasket
Inlet & exhaust manifold gaskets
Main and Big end bearings
Service manual Oil filter

Apr 25, 2016 | Cars & Trucks

1 Answer

Why is there no compression in engine on my 1991 mitsubishi pajerno


This has to be because of a mechanical problem in the engine. Possible sources are the timing belt is broken (one indication is the starter spins the engine faster than normal, because the camshaft that opens and closes valves is not turning with the crankshaft), or the head gasket has failed (from overheating as the most likely cause), or badly worn piston rings and/or valves not sealing well (common on high mileage engines).
Compression is built up in the upper part of the cylinder where combustion occurs, so leaks or lost compression are due to valves not sealing, or head gasket that seals the cylinder head to the engine block-sometimes the aluminum cylinder head can warp due to overheating, and the head gasket no longer can maintain a seal. Or also the piston rings are worn so bad that compression will leak past them into the crankcase. For valves or head gasket, the cylinder head has to be removed and repaired. For the rings, the engine has to be rebuilt entirely.
First check if the timing belt is still intact.
.

Apr 02, 2014 | 2002 Mitsubishi Galant

1 Answer

Have oil in one of the spark plug cylinders what would be causing this ?


broken/worn piston ring(s). Each piston has 2 rings. These can be replaced by the DIY mechanic by
1) removing head of engine (remove head gasket - you'll replace it), then
2) manually wind the engine (with a ratchet wrench & socket) til the piston in question pops up
3) remove both rings (with ring pliers - available from any auto parts store)
4) install 2 new rings (with a ring installation collar - available at any auto parts store)
--- choose ring installation tool to the correct size for your pistons.
5) re-install head of engine (replacing head gasket)

Note that this procedure preserves the engine timing, so you need not reset it.

Dec 27, 2010 | 1997 Toyota Avalon

2 Answers

What parts do i need to do the piston rings


You will need a complete engine gasket set as well as the rings of course. You do have the hones and other special tools to do this job, correct?

Sep 20, 2010 | 1984 Suzuki Gs 550 L

1 Answer

Head Gasket changed >>> if installed incorrectly or wrong model ?


Head gasket is not your problem when you had the top end of the engine rebuilt it was 2 strong and blew the bottom end out so meaning the cylinder has 3 rings if they leak or on leaks you get wash out in the cylinder and it will burn the oil. the lurching is OK as long as its not a clunking

May 10, 2009 | 1998 Toyota Tercel

1 Answer

1999 tt-r250 blowling LOTS of smoke all of a sudden


The seals in the valve guides are going bad or the cylinder head is not down tight > letting oil into the cylinder, or you have a bad head gasket and "O" ring seal. The problem could be any one of the three causes noted above.

Try tightening down the cylinder head. It may fix the problem. If not then the fix is to pull the cylinder head and inspect the head gasket and "O" ring seal if one is present. If the gasket is dirty and oily then replace the gasket & "O" ring. Consider lapping the valves while the head is off. This will give the valve face and valve seat a fresh mating surface thus providing more power.

If the gasket is clean and dry then the shop will need to replace the valve guides. Be sure they also lap the valves.

Please rate this solution. Thanks

Apr 12, 2009 | 2002 Yamaha TT-R 250

1 Answer

I have an xs 650 1980 yamaha I bought it having had an engine rebuild but one spark plug keeps oiling up and then runs on one cylinder. Thanks


There are only four ways for oil to get to the spark plug. Bad head gasket, bad rings on the piston, Cylinder scored or warped, and bad valve seals.
  • Start with the most likely, bad head gasket. When they rebuilt the engine they could have left out an oil seal 'O' ring. Check the head bolts. Did they tighten the top end down tight? Are you seeing oil on the outside of the head and cylinder? When the cylinder is firing properly, do you hear any head gasket leakage?
  • Do a compression check on both cylinders. This should tell if rings and valves are ok. Does the bike smoke most all the time when running properly? Does it only smoke when first started and when pulling away from a stop light? Bad rings will smoke all the time. Bad valve seals will smoke when starting out.
  • Scored cylinders are best checked with the head removed. Warped cylinders can only be checked with the head removed and by using a cylinder hone. The hone will reveal any low areas.
Chances are slim that you can avoid pulling off the cylinder head. Best wishes.
Please rate this solution after the problem is found. Thanks.

Mar 20, 2009 | 1980 Yamaha XS 650 G

Not finding what you are looking for?
1998 Cagiva Canyon 500 Logo

Related Topics:

124 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cagiva Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

6480 Answers

Steve P
Steve P

Level 3 Expert

3712 Answers

Are you a Cagiva Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...