Replacing front fender which model would i pick?

A salvage yard would be a likely source of interchangeability information.

Pay the mechanic at the dealer. I do not recommend removing the front fender as it protects you and the engine from flying road debris. When you don't have a front fender, the tire picks up sand and other small debris and pitches it forward where the particles lose velocity and end up spraying you in the eyes or face. This turns cool into fool in a hurry.

Replace left front fender - Fixya

www.fixya.com/cars/t26028082-replace_left_front_fender

Dec 29, 2015 - replace left front fender - Hyundai Motor 2003 Elantra question. ...Question about Hyundai Motor 2003 Elantra. Open Question ... How do i remove left front fender clip on a Lincoln ls 2002? Jan 04, 2015 ' 2002 Lincoln LS.

Replace 2003 hyundai elantra front passenger outside door ...

www.fixya.com/cars/t17348691-replace_2003_hyundai_elantra_front

Mar 26, 2013 - Question about Hyundai Motor 2003 Elantra. Open Question.Replace 2003 hyundai elantra front passenger outside door handle. Need to replacebroken exterior door handle on front passenger .... replace left front fender.

They should just be bolted on, probably be a bolt or clip to the front bumper probably 4 or 5 bolts along the top of the fender, probably 1 in the door jamb and one at the bottom of fender...you will have to remove wheel and the splash shield

Hello robert.... Battery Replacement

Removal Procedure

Disconnect the negative battery cable (2). Refer to Battery Negative Cable Disconnect/Connect Procedure .

Remove the wheelhouse liner. Refer to Wheelhouse Liner Replacement - Front .

Lower the vehicle.

Open the positive battery cable connection cover.

Loosen the positive battery cable bolt.

Remove the positive battery cable (1).

Remove the front fender rear bracket to side rail bolts.

Remove the front fender to front fender rear bracket upper (1) and lower (2) bolts.

Remove the front fender rear bracket.

Remove the battery hold down retainer bolt and retainer.

Important: Do not tip the battery more than 40 degrees during removal.

Remove the battery.



Installation Procedure

Important: Do not tip the battery more than 40 degrees during battery installation.

Install the battery.
Notice: Refer to Fastener Notice in Cautions and Notices.

Install the battery hold down retainer and bolt. Tighten the bolt to 25 N·m (18 lb ft).

Install the front fender rear bracket.

Install the front fender rear bracket to side rail bolts. Tighten the bolts to 20 N·m (15 lb ft).

Install the front fender to front fender rear bracket upper (1) and lower (2) bolts. Tighten the bolts to 20 N·m (15 lb ft).

Install the positive battery cable (1).

Tighten the positive battery cable bolt. Tighten the bolt to 17 N·m (13 lb ft).

Close the positive battery cable connection cover.

Install the wheelhouse liner. Refer to Wheelhouse Liner Replacement - Front .

Connect the negative battery cable (2). Refer to Battery Negative Cable Disconnect/Connect Procedure .

Joe
Thanks for choosing Fixya!

Battery Replacement

Removal Procedure

Disconnect the negative battery cable (2). Refer to Battery Negative Cable Disconnect/Connect Procedure .

Remove the wheelhouse liner. Refer to Wheelhouse Liner Replacement - Front .

Lower the vehicle.

Open the positive battery cable connection cover.

Loosen the positive battery cable bolt.

Remove the positive battery cable (1).

Remove the front fender rear bracket to side rail bolts.

Remove the front fender to front fender rear bracket upper (1) and lower (2) bolts.

Remove the front fender rear bracket.

Remove the battery hold down retainer bolt and retainer.

Important: Do not tip the battery more than 40 degrees during removal.

Remove the battery.



Installation Procedure

Important: Do not tip the battery more than 40 degrees during battery installation.

Install the battery.
Notice: Refer to Fastener Notice in Cautions and Notices.

Install the battery hold down retainer and bolt. Tighten the bolt to 25 N·m (18 lb ft).

Install the front fender rear bracket.

Install the front fender rear bracket to side rail bolts. Tighten the bolts to 20 N·m (15 lb ft).

Install the front fender to front fender rear bracket upper (1) and lower (2) bolts. Tighten the bolts to 20 N·m (15 lb ft).

Install the positive battery cable (1).

Tighten the positive battery cable bolt. Tighten the bolt to 17 N·m (13 lb ft).

Close the positive battery cable connection cover.

Install the wheelhouse liner. Refer to Wheelhouse Liner Replacement - Front .

Connect the negative battery cable (2). Refer to Battery Negative Cable Disconnect/Connect Procedure .
hope this helps . please rate my response.

I'm no expert on new Hogs but try this.Protect your tank,grab the seat on both sides in the middle and push it backwards and it will pull the tab out from it's holder.Pull the front up and pull it toward the front,this will release the rear tab hold down.Pick up the seat.I suppose there could be a stud attached to the seat that goes through the rear fender.Reach under the fender above the wheel and undo the nut.Pick up the rear of the seat and pull it back to release the front tab,pull the seat off.Sounds a bit much to get to the battery,I vote for pushing and pulling the seat to release the tabs.

Take off the tyre and remove the plastic inner fender first.

Can you remove the wheel well splash shield and get access to the bolts? Body shop techs have a special tool to get into this area.

Here's a 97 Probe whcih was the same as a 626 in 1997:

Fender, Front Removal

1. On GT models, remove the side sill extension. Refer to Section 01-08 for the removal and installation procedure.
   

1. Remove the front fender bolt located in the door jamb opening.
   
   
   RH Side Shown, LH Side Similar
   
   
   
   
   

1. Remove the three upper front fender bolts located on top of the front fender (16005) inside the engine compartment.
   

1. Raise and support the vehicle.
   

1. Remove the wheel (1007).
   

1. Remove one push pin and five front fender splash shield bolts and remove the front fender splash shield (16102).
   

1. Remove the upper front fender brace screw.
   

1. Remove the inner front fender bolt.
   

1. Remove the screw holding the front bumper cover (17D957) to the front fender.
   

1. Remove the two lower front fender bolts.
   

1. Remove the front fender.
   

Installation
To install, reverse the removal procedure. Tighten the front fender bolts to 7-9 Nm (61-86 lb-in).

Have you tried lowering your pick ups? If they are too close to your stings they could be picking too much. also try playing with the settings on your amp.