Engine light blinks three times then stops and then blinks three times again. Dropped the bike and now need to know how to reset this fault light

Yamaha yellow blinking light start Motorcycles Questions ...

www.fixya.com > ... > Tags > yellow blinking light start > Motorcycles

Ad. Question about 1997 YZF 750 R ... oil light blinking on 2004 yamaha r1 oil lightblinks 10 times stops then blinks 10 ... My yamaha r15 v2 I drive to bike after sometimes yellow engine light on aftersometime I light on to yellow engine light of.

Yamaha blinking yellow light Questions & Answers - Fixya

www.fixya.com > Forum > Tags > blinking yellow light

oil light blinking on 2004 yamaha r1 oil light blinks 10 times stops then blinks 10 times ... Question about 2008 YZF-R15 ... My yamaha r15 v2 I drive to bike after sometimes yellow engine light on aftersometime I light on to yellow engine light of.

[Ownership Thread]: Yamaha YZF-R15 - xBhp.com

www.xbhp.com/talkies/.../4854-yamaha-yzf-r15-1951-print.html

Jul 11, 2013 - 4 posts - ‎3 authors
2months back i got this problem while riding the engine goes off, but ... of heavy traffic after transporting it from my home town. then it works fine and all of a sudden i find the bike engine light blinking. it reads '42'. then after showing it to ... the ECU alone wil cost me to 10k. and obviously it is very expensive ...

Yamaha YZF-R15 version 2.0 - xBhp.com

www.xbhp.com/.../20138-yamaha-yzf-r15-version-2-0-a-786-print.html

Nov 26, 2013 - According to me the problem of chain with my bike is because i ... list about the required changes at 10k kms like Fork oil change and ... On switching on the ignition, the engine malfunction light, the orange(?) ... From your description that a longblink coupled with 3-4 short blinks it .... All times are GMT +6.5.

Yamaha YZF-R15 version 2.0 - xBhp.com

what model is it KY KV need that and Spec. If it blinks 3 times it indicates a lower service fault. While blinking hit the stop button 3 times fast, then read the code. It will blink, pause then blink again and repeat. What is that code and I can help you. IE 4 blinks pause and 3 indicates code 43

Pull any error codes.

The engine light lights up when you turn the ignition switch on, then goes off. After four seconds, if it comes on again and stays on, there is a present fault code. When it is an historical fault code, it comes on with ignition and goes off then comes on and goes off again. I believe in like 4 second intervals. A historical code will not be removed until a cycle of 50 ignition on/of intervals has passed. In other words, the engine light will continue to light two times when ignition switch is turned on, after 50 on/off cycles have passed the historical codes will no longer affect the engine light when starting.
If you will hold the odometer button on the side of the console down, and turn the ignition on and off, three times I think, waiting for the fuel pump to stop before turning the ignition switch to the off position, and one second until you turn it on again, the third time holding the odometer button down until the engine light begins to blink it will begin to blink in a fast sequence showing the fault codes will follow.
First indication of fault code display is rapidly blinking engine light. After that count the number of times the engine light lights up. There will be a brief pause between digits. If there are multiple codes stored, the rapid blinking will separate each. Once the fault codes begin to repeat, you have gone through all stored codes.
Tips: Have a pencil and paper ready.
Maybe ask a friend to help out. Sometimes a second pair of eyes can be good.
Go through a couple of cycles, so that you are sure you haven't missed any codes.
One example is if it blinks 3 times, pause, the blinks 2 times, that means 32.
Code 32: Rear Fuel Injector

The light blinking twice means there is a fault within the system and it is a code to tell Panasonic where roughly the fault lies.
Go to Panasonic's web site and look for your set then input the fault code and hopefully they will tell you where the fault lies.

You need to reset your change oil warning light. To do this, turn the ignition key to on but do not turn over the engine. Then rapidly push down the gas pedal three times. This will reset the system and turn off the blinking light. Then when you drive another 3000 miles, that light will once again tell you it is time to have your oil changed. J.

Put the Key into the Ignition and turn from OFF to ON (not START) Position, which is right before Start and do this three (3) times. On the third time leave the Key in the ON (not Start) Position.
If you have a didgital Odometer look there for codes (example P 0123). There may be several so wait until it reads "donE". Record these Codes.
If you do not have anything reading in the Odometer window: Look immediately at the Check Engine Light and count the number of times the Check Engine Light blinks (on and off). There are two (2) digit blinks, then a pause followed by pause followed by more blinks. Record the number of blinks. The last set should be five (5) blinks followed by five (5) blinks.
Get back with me on what the blink counts were. (example 18, 23, 55).
Let me know if this helped, and provide me with additional information I requested. Contact me at FixYa.com using the comment section of tyour original Posted Question.

with the key in the on position, locate the reset button in the drivers side fuse panel,pess the button when the oil light blinks press again, should stop blinking and the chimes will stop, hope this helps

On a Envoy you turn the key to run but don't start it. Then push and release the gas pedal 3 times within 5 seconds. The change engine oil light should blink for 5 seconds meaning you have reset the system. If it doesn't blink for you do the procedure again.

Engine management light was on permernantly after replacing battery, took advice and let bike idle until thermo fan started, turned bike off and let thermo fan stop, restarted bike and engine management light went off. this proceedure resets engine management system. GREAT ADVICE thanks.

is the cean light blinking 7 times and then repaeating?? If so this is a water heating fault and means that the computer sensed that the water temp didnt rise just 3deg in the last main wash cycle. If its not blinking 7times then repeat, it sounds like the user interface (membrane switches) have failed. Let me know more and i can help.