Question about 2000 Harley Davidson FLHTCUI Electra Glide Ultra Classic

Open Question

How do you adjust the front brake of a 2003 Harley Ultra Classic?

Posted by Anonymous on

Ad

5 Related Answers

Anonymous

  • 80 Answers

SOURCE: removing harley davidson ultra classic gas tank

Drain the fuel either by siphening or removing the cross over tube at the front of the tank and letting it drain that way or just block off those cross over lines and leave the fule in the tank for removal.

0) remove seat
1) drain fuel
2) undo cross over line (bottom front of gas tank.
3) shut off pet **** and remove fuel line from pet ****.
4)there should only be 2 bolts holding the tank on, one at the top front of the tank and one at the back of the tank.

All in all a pretty easy (but possibloy messy) job.

Posted on Jun 06, 2009

Ad

Anonymous

  • 69 Answers

SOURCE: How do I change the front and rear brakes on a

Not too hard - Undo the two bolts on the caliper and then seperate the caliper and pull the old ones out. Insert the new ones and put the bolts back in to hold the caliper back together and then install them back on the bike with the two retaining bolts. Use a bit of lock tight (Blue) on the threads. Warning do not let anyone apply pressure on the brakes while you have them off the bike or you will have a mess and/or a problem.

Posted on Jun 21, 2009

Ad

Anonymous

  • 69 Answers

SOURCE: 2002 harley davidson ultra classic setting the clock

Turn the Bike on and the Radio off and then follow the buttons on the screen. Most people think you have to do it while it is running and this does not work

Posted on Jun 28, 2009

wd4ity

wd4ity

  • 4565 Answers

SOURCE: How to change the front

Take the two bolts out that hold the front caliper onto the fork slider. Lift the caliper off and take the pads out. You must compress the brake caliper piston back into the caliper body. I usually use a large C-clamp or a large slip joint pliers to compress the piston back into the caliper. Protect the finish on your caliper with rags or thin pieces of wood. Once you get the piston back into the caliper, replace the pads with the new ones making certain that the fiber side of the pad is facing towards the rotor. Put the caliper back into position and reinstall the two bolts. Torque them to 25 foot pounds of torque. Work the front brake lever until you have a full firm brake.

Good Luck
Steve

Posted on May 02, 2011

ambiont2000

  • 1 Answer

SOURCE: wiring diagram for tourpak on 2003 Harley Road King Ultra Classic

i have a 2003 ultra classic my riding lights keep blowing the fuse it wont do it sitting in the garage i have gone thru the wiring harnessing looking for the short fixed many things but still have the problem the turn signals work the brake lights still work so where do i look

Posted on Jun 30, 2011

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the torque specs for 2010 harley ultra classic, front axle nut, front brake calipers


Front caliper -

Brake Pad Pin = 75-102 INCH lbs.

Caliper to Fork Bolts = 28-38 FOOT lbs.

Aug 23, 2014 | 2010 Harley Davidson FLHTCUTG Tri Glide...

1 Answer

I have a 2003 harley ultra classic and my brake light stays on what should i check for? also my front running light are not working and i have checked the fuses and the wiring what should i check next?


Check the front and rear brake switches. Unplug one of the connectors at the rear switch. If the brake light goes out out, the problem is the front switch, which is located inside the right handlebar control housing.Check the bulbs in the running lights.

Aug 25, 2013 | Harley Davidson Motorcycles

1 Answer

2008 ultra classic, brake light stays on. replaced front brake switch and still stays on.


check to see if there is a pedal brake light switch for the rear brake if so check out that switch as well

May 23, 2012 | 2008 Harley Davidson FLHTCU Ultra Classic...

1 Answer

No problem I need torque spec's front brake rotor,front axle nut and front brake caliper bolts 2005 Harley davidson ultra classic


caliper torque 28-38 ft lbs,front axle nut torque60-65 ft lbs. front brake rotor torque 16-24 ft lbs. straight from harley manuel.

Aug 14, 2011 | 2005 Harley Davidson FLHTCUI Electra Glide...

1 Answer

I just got a 92 ultra and the guy i got it from said the cruise worked before he put grips on and now it dose not can you help to adjust


When a problem is encountered after something has been done go to the last thing you did ( put grips on) and check what was done. Look for pinched wires binding cables whith housing open and closed. A card board spacer has to be inserted in crack between front brake lever and housing to retain internal piston in handle bar assy. or damage to front master cylinder piston can result (brake won,t disengage as plastic piston gets stuck.

Dec 01, 2010 | 2003 Harley Davidson FLHTCUI Electra Glide...

Not finding what you are looking for?
2000 Harley Davidson FLHTCUI Electra Glide Ultra Classic Logo

448 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

6487 Answers

Mike

Level 3 Expert

4369 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...