Question about 2005 Suzuki RM 250

1 Answer

Replacing fork seals and need to know amount of oil for outer fork on a twin cartridge tpye fork, rm250 2005

Posted by sullem_largs on

Ad

1 Answer

Anonymous

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 653 Answers

Try about 250-350 cc

Posted on Mar 24, 2010

  • Anonymous Mar 24, 2010

    250 -350 cc

×

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My front fork seals need replacing on my 2005 model TE450, i don't know the specifications, and exactly how much oil to use in each fork


forks need to be removed,and disasemble,and cleaned,new fork seals,reasembleb fit new seals, refit damping cartridge,fill fork with 5w fork oil upto 120mm from top,refit spring, refit fork cap

Aug 14, 2010 | Husqvarna TE 450 Motorcycles

1 Answer

Volume of fork oil needed per fork for a 1986 VF 400 nc 13


Well, when you take off the fork make sure you empty it first before anything else then make sure that the fork pressure spring is released before changing the seals. The fork oil amount should be no more than 200 cc or no less than 190 cc

Jun 24, 2010 | 1986 Honda VF 400 F

1 Answer

Replacing fork seals and need to know amount of oil for outer fork on a twin cartridge tpye fork rm250 2005


Outer cartridge on the twin chamber Showa fork for an RM250 uses 350ml of 5W oil.

May 14, 2010 | 2005 Suzuki RM 250

3 Answers

I need to know the oil capacity of the front forks on my 1999 Suzuki Marauder VZ800.


FORK OIL
• Place the front fork vertically without spring.
• Compress it fully.
• Pour specified front fork oil up to the top level of the outer
tube.
Capacity (each leg): 490 ml (16.6/17.3 US/lmp oz)
99000-99044-L01: SUZUKI FORK OIL L01
or an equivalent fork oil
• Move the inner rod slowly with the special tool ten times and
more until no more bubbles come out from the oil.
09940-52841: Inner rod holder
NOTE:
Refill front fork oil up to the top of the outer tube so that bubbles
are visible while bleeding air.
• Refill specified front fork oil up to the top level of the outer
tube again. Move the outer tube up and down several strokes
until no more bubbles come out from the oil.
• Keep the front fork vertically and wait 5 – 6 minutes.
NOTE:
* Always keep oil level over the cartridge top end, or air may
enter the cartridge during this procedure.
* Take extreme care so as to pump out air completely.
• Hold the front fork vertically and adjust fork oil level with the
special tool.
NOTE:
When adjusting the fork oil level, compress the outer tube fully
without the fork spring.
Fork oil level: 153 mm (6.02 in)
09943-74111: Front fork oil level gauge

Dec 18, 2009 | 1998 Suzuki VZ 800 Marauder

1 Answer

Front forks will not seal


dissassemble forks and replace fork seals.(and oil) becareful forks are under a lot of spring pressue. use a workbench vise to hold fork tubes. you will need the manual for this. plus you will need to know the "proper" amount of fluid to put back into the forks.

Oct 05, 2009 | 2001 Yamaha WR 426 F

2 Answers

2001 yzf426 front fork leak


Each fork has an outer dust seal, and an inner seal inside of that. Dirt gets between the seal lip and the fork slider and causes the oil to escape. The fix is to have them (Both sides) replaced. You need a fork seal driver tool (Size specific for the size of the fork) and something to measure out the oil amount. It's not an easy job, if you have never done it. Also... if the oil has never been changed, it's due.

Aug 19, 2009 | 2001 Yamaha YZ 426 F

3 Answers

How do I change the fork seals on a 2008 Honda CRF 250 r? Do I use a special tool? Oil? How much oil? Thanks so much for your expertise. Do I put equal amounts of oil on each side? Inner tube- outer tube?


hi,replacing the seal is quite easy,although it will sound complicated,jack up or lift the bike off the ground so that the front wheel is in the air(about 12-14 inches should be enough,remove the front wheel from the bike,remove each fork leg,this is done by undoing the bolts(4 on each leg)the front fork is quite easy to work on just do one at a time,remove the dust cover from the top of the staunchion tube(larger diameter tube),beneath that dust cover you should see a retaining clip that holds the seal in place,remove the retaining clip(and dont lose it),the seal is now ready to remove,the easiest way that i know to do this is to force a screwdriver through the body of the seal,you may need to hit the screwdriver with a hammer as some seal have a tin backing plate,put a hole through the seal on each side of the fork leg taking care not to damage the chrome of the fork leg,then use the screwdriver to lever the seal out of the fork leg,to reinstall the new seal,put a smear of grease or oil around the outside of the new seal,slide the new seal down the fork leg and seat it squarely into the fork tube,very carefully tap the new seal into place being very carefull not to damage the outer surface,i use a small piece of dowell type timber to do this as the wood doesnt damage the seal surface,i use a small ballpeen hammer to tap the wooden dowell,once you have the seal seated down the tube you should be able to see the groove for the retaining clip,reinstall the retaining clip making sure it is seated corectly,replace the dust cover,if you are going to replce the fork oil or top it up do this once the fork leg is back in the bike,repeat the whole procedure for the other fork leg,once you have done the fork seals reinslall the fork legs back into the bike and refit the front wheel,to top up the oil in each leg,simply undo the large cap on the end of the fork leg,you may have to remove the handlebars to do this,be carefull as the cap will be spring loaded and can easily fly off if you are not ready for it,top up or fill with the correct weight oil for your bike(normally a 10w oil),check with your local honda agent for the correct quantity,normally between 400-500 mls,this all sounds quite complicated but is actually quite easy and can be done with a minimal of tools,each fork shold take about 1/2 hr to do...hope this is a help to you

Jul 15, 2009 | 2005 Honda CRF 250 R

1 Answer

Seals blown on front shocks


to remove seals you will need to remove each fork leg from the bike,i put the bike on the centre stand and jack under the motor to get the front wheel off the ground,after you remove the fork leg,remove the dust cover(if fitted),remove the circlip holding the old seal,you may have to stab through the old seal with a screwdriver to remove the seal from inside the leg(be carefull not to damage the chrome on the fork leg),clean around the surfaces and install the new seal making sure it goes back in dead square,refit the circlip,then refit the dust cover,replace fork tube back in bike and top up with new oil,most bikes take between 300 to 500cc of oil,but check with your local shop as all bikes are different,and you can adjust the amount of rebound damping by varying the amount of oil you put back in,..sounds complicated but quite an easy job..hope this helps

Jul 04, 2009 | 1995 Suzuki GS 500 E

2 Answers

How to fill the front suspension on a ktm exc 2001


If you get the sevice manual or contact a dealer to get the correct oil amount for your bike, they need to know the model and year, you have to have the forks off the bike. take the fork caps off, take the springs out compress the upper fork tube all the way and add the specified oil. if they also give you the measured amount from the top that's the best way to get both fork oil levels exact. there is a special tool that you set the oil level in millimeters and it sucks out the oil to the right level, but before you do that step after adding the oil always pull and push on the cartage rod several times to remove air from the cartage tube. you will hear the air coming out and you will feel the changes in the cartage rod as the cartage tube fills up with oil and the air is removed.
something i'm confussed on though is if you replaced a seal you would have had to brake down the fork to replace it. you would have poored the oil into a container, cleaned all the internal parts,and used a fork seal driver to install the new seal. part of your question asks where do i put the oil in? thats in the open end of the fork after you have taken off the fork cap. It sounds to me like you only replaced the dust seal on one fork. that is not going to fix your leaking fork. you need to replace the oil seal thats pressed inside of the top fork tube.

Dec 01, 2008 | 2008 KTM 200 EXC

Not finding what you are looking for?
2005 Suzuki RM 250 Logo

Related Topics:

269 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

6487 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

217 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...