Question about 2004 Suzuki RM-Z 250

There are 3 marks on 2004 rmz 250 fly wheel what one is tdc

1 Answer

Anonymous

Level 3:

An expert who has achieved level 3 by getting 1000 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Vice President:

An expert whose answer got voted for 100 times.
Master
518 Answers

Hello mate, if you do not have a manual, take the spark plug out and the casing off the flywheel, Find a small stick or screwdriver and place it in the sparkplug hole but do not let go of it, then with the other hand turn the flywheel until the piston reaches the top of the bore, then turn the flywheel left and right, then check the marks, this should tell you which one is TDC.

Posted on Jan 31, 2010

Add Your Answer

Upload

Upload an image from your computer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

1 Answer

The best way to tdc with the moter in tact

Try this link Sheldon. Locating Top Dead Center TDC

Aug 18, 2016 | Cars & Trucks

0 Answers

What are the valve clearances on my 2014 rmz 250

Apr 15, 2016 | Motorcycles

0 Answers

Valve clearances on my rmz 250 2014

Apr 15, 2016 | Motorcycles

1 Answer

Isuzu trooper 2004 model 4jx1 engine what was the fly wheel marks if it was at tdc

if flywheel is fitted in correct position the timing mark on the front top cambelt gear is at 12 O clock and with starter motor removed you will see 3 lines stamped in the interuptor ring that is bolted to the rear of the flywheel if manual on early builds, also there is a notch in flywheel which you can see if gearbox is out this goes at 6 O clock

Dec 07, 2014 | Isuzu Cars & Trucks

1 Answer

Isuzu trooper 2004 model 4jx1 engine where did was the fly wheel marks if it was at tdc

could be on the flywheel or the front pulley i just dont know where without a look myself but someone might know on here as and when they get time to answer questions

Dec 07, 2014 | Isuzu Cars & Trucks

1 Answer

Timing

Sounds like a valve timing problem to me. Put the engine at TDC (top dead center). There will be marks on the cam gear that should be aligned with the top of the head casting. This is something that could be damaging to the engine so be careful. A manual is a good investment.

Apr 02, 2014 | 2004 kawasaki KX 250

0 Answers

Which timing mark on fly wheel do you use for tdc on 04 yz450f

Feb 02, 2012 | 2004 Yamaha YZ 450 F

2 Answers

Need help timing 1987 honda xr80..any help with markings for tdc and where to set cam..have no book and bike was more or less in pieces when we got it. robbed top half from slightly older 80cc. bike has...

Backfiring through the carb isn't a timing issue unless you're firing at BDC (180 degrees out).
or have bad/missing/cracked piston rings / hole in the piston.
I mean, correct me if I am wrong, but that thing IS a 2 stroke, right?

Mar 15, 2011 | 1987 Honda XR 250 R

1 Answer

Witch marks on magnitio i use to set valve timing in a 2004 rmz 250

With the valve rocker covers off and magneto inspection plug and centre plug removed, turn motor using nut on magneto, counter-clockwise until a line appears centrally in the inspection window. This will be at Top Dead Centre (TDC).
To check this, all rockers should at rebound with all valves closed. There should be a tiny amount of play on all rockers.
If not, (being a 4 stroke) rotate motor one full turn counter-clockwise.
All engine work or strip downs must commence from the position of TDC.
Cheers!

Nov 14, 2010 | 2004 Suzuki RM-Z 250

2 Answers

Fly wheel problem on a jeep

if its a 4JX1 diesel, yes it goes in 1 spot yet it can be bolted up in every location
put crank pulley timing mark to TDC can also check by removing cam belt top cover and check timing mark aligned up with mark at 12 O clock then flywheel has small notch in edge that must go at 6 O clock (facing down) look closely it is hard to see due to flywheel sunk into back of block.

Oct 19, 2008 | 2000 Isuzu Trooper