Question about 1975 kawasaki Z1B

1 Answer

I need to fit a clutch cable to my kawasaki z1b900 i need step by step instructions please

Posted by stanlejim on

Ad

1 Answer

BeninVa

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 389 Answers

To remove the old cable first shorten the mid-cable adjuster to give as much free play as possible. If you need more free play screw in the adjuster at the clutch lever as much as possible and line up the slots so you can disconnect the cable from the clutch lever. Then remove the shift lever, and possibly the left footrest if needed to remove the front sprocket cover. Remove the cotter pin and disconnect the cable from the clutch release lever. Make a note of the routing of the old cable so you can replace it. Install the new cable with a new cotter pin at the lower end first, and route it the same as the old cable. To adjust the new cable, shorten the mid-cable adjuster as much as possible. At the clutch lever, turn the adjuster in and leave about 1/4" of threads showing between the locknut and the lever body. With the front sprocket cover still off, loosen the locknut on the clutch release lever and back the screw 3 or 4 turns. Turn the clutch adjusting screw in until it becomes hard to turn and then back it off 1/2 of a turn and tighten the locknut. Now lenghten the mid-cable adjuster until there is no free play and tighten the locknuts. Check that the lower end of the cable is fully seated in it's socket. At the clutch lever, turn the adjuster in so you have 1/16" free play, and tighten the locknut. Replace the front sproket cover and the shift lever and footrest.

Posted on Dec 23, 2009

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i remove a 1982 kawasaki kz 1000 starter motor


Follow the specific instructions in the Factory Service Manual. Step 1 - Remove the heavy wire from the starter solenoid. Either end will suffice. Step 2 - Remove the chrome cover over the starter. Step 3 - remove the screws that hold the starter motor in place. Step 4 - Lift the starter motor out of the engine. NOTE: removing the carbs may make this step simpler. The "business" end of the starter should come out of the splined starter clutch gear. If you have trouble removing the starter from the clutch gear, you may need to remove the left side stator cover to gain access to the starter clutch and chain. The exploded parts diagram is available HERE Kawasaki Motorcycle Parts 1982 KZ1000 J2 STARTER MOTOR STARTER CLUTCH...

Aug 24, 2014 | kawasaki Csr 1000 Motorcycles

1 Answer

Installing klutch


Buy clutch cover gasket
Unhook clutch cable at clutch cover
Remove clutch cover
Remove 5 clutch spring bolts
Remove springs
Remove pressure plate
Remove plates and disc noticing order
Replace with new plates/disc in same order (after soaking in oil for at least a few hours, over night would be better.
Put everthing back together in order of removal.

May 03, 2009 | 1997 kawasaki VN 800 A Vulcan

Not finding what you are looking for?
1975 kawasaki Z1B Logo

236 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

6480 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

217 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...