2004 Burgman 650. Ignition light flickering

find the Fuse holder near battery on Wire, replace
check others, check First

650 Regulator Rectifier experience - Suzuki Burgman Forum - BurgmanUSA

burgmanusa.com/...burgman.../49945-650-regulator-rectifier-experience...
Apr 18, 2012 - This is my experience swapping out my rectifier with an aftermarket Mosfet unit. I have no long term review right now but here are some ... scooter stalls at low rpm's - Suzuki Burgman Forum
May 23, 2015
Starting / Electrical issue with 2008 Burgman 400 - Suzuki ...
Feb 14, 2013
2003 650 CVT motor issues! - Suzuki Burgman Forum
Dec 9, 2010
OIL LIGHT ON - Suzuki Burgman Forum - BurgmanUSA
Apr 17, 2004
More results from burgmanusa.com

How to wire a GY6 scooter regulator / rectifier and how it all ...

? 4:56
www.youtube.com/watch?v=u8dGhevthRI

Oct 28, 2009 - Uploaded by serpentza
How to wire a GY6 scooter regulator / rectifier and how it all works (Part 3 .... My scooter has no spark how to fix. gy6 chinese scooter 139qmb ...

650 - Resetting Oil Change Indicator
(The Owner's manual is not very clear on this)

• 1) Turn off ignition.
  2) Hold both the SELECT and RESET buttons in.
  3) Turn ON ignition
  4) After 2 seconds the indicator to change oil should extinguish.

__________________

sounds like your having a problem with the ignition. its not shutting power off completly.

These are not a battery related issue, if it were the car would not have restarted. You should have the systems electronic control module scanned for fault code, this may explain the stall, remember this engine is likely to be fully electronically controlled, fuel ignition system all of it. It would aid if you gave the model and make and year of the car or truck.

Symptoms- Engine Light ON (or Service Engine Soon Warning Light)
- Lack/Loss of Power
- The engine may be harder to start
- The engine may stumble or stallPossible causes- Ignition/Distributor engine speed sensor harness circuit is open or shorted
- Ignition/Distributor engine speed sensor poor electrical connection
- Faulty Ignition/Distributor engine speed sensor
- Faulty Crankshaft Position sensor
- Low battery charge
- Faulty Engine Control Module (ECM)When is the code detected?The P0322 code is triggered when the Engine Control Module (ECM) detects no signal.P0322 VOLKSWAGEN DescriptionIgnition failure sensor is used to check whether the spark ignition is occurred correctly or not and also used to tachometer drive. The sensor monitors the voltage difference between a resistance which is on the battery circuit for ignition coil. When the ignition coil works properly, the electric current through the resistance is detected as voltage drop. This is confirmed for every ignition event with the crankshaft sensor and the camshaft sensor. If ECM detects a malfunction, no ignition is possible, so the engine would not start. If there is no ignition signal for a predetermined cycle for one or two ignition coils, an ignition coil circuit failure exists.

The loud click kinda indicates the starter is the problem. A fainter click would implicate the starter relay as the failing component.

Since I can't hear the noise, I would say first check the starter for 12 volts from hot to ground when the ignition is in start position. If you get 12 volts upon this test, then it's most likely the starter relay.

Then check the relay for continuity with starter disconnected from it and the ignition in start position. To find these components, just trace the red cable from the battery.

More info, let me know.

Charlie

P.S. The lights flicker because the battery voltage is dropping when the starter tries to turn over.

the flickering oil light is a common problem with the 2.7 engine. as long as the oil level is full and oil is changed regularly, and the light just flickers and doesnt stay on , shouldnt be a problem, or get the oil sending unit changed. the second problem car stallings sounds like either cam or crank position sensor. does the engine light come on. if so the code should tell you.