2003 Yamaha V Star Classic Logo

Related Topics:

Posted on Sep 27, 2009

Looking for instructions to install Yamaha silverado windshield

Looking for instructions to install used silverado windshield mounting bracket on a 2003 650 classic

5 Related Answers

Anonymous

  • 292 Answers
  • Posted on Mar 21, 2009

SOURCE: problem with shaft drive (cardan) for my Yamaha Dragstar

SKU: 5FB-Y4617-00-00
SHAFT DRIVE SUB ASSY
SKU: 5FB-Y4617-00-00
SHAFT DRIVE SUB ASSY

Hi i just checked on stadium yamaha site and above is the SKU # for both, 98 and 03.... both the same so go for it
http://www.stadiumyamaha.com/pages/parts/viewbybrand/parts.aspx

Ad

Anonymous

  • 292 Answers
  • Posted on Apr 02, 2009

SOURCE: how to lower the idle on a 2002 yamaha 650 v-star classic?

under the left side of the gas tank you will see i black knob/screw at the end of what looks like a hose. the knob faces the rear of bike. that adjusts the idle. its real easy to find and the only adjustment you can make to the carbs.

Anonymous

  • 18 Answers
  • Posted on May 16, 2009

SOURCE: Need to get oil

First of all, I want to compliment you on your bike! That V-Star is in so many ways, one of the best all around bikes....Very durable engines, user friendly, comfortable and DEPENDABLE, not to mention one the best value to dollar ratio on the market, right along next to the Suzuki Boulevard....Not to get off subject but I enjoy these bikes thoroughly!

You want to make SURE that the only oil you use is a quality oil, which will have THE seal of approval stamp on the bottle that says that it meets the requirements of all the major motor corporations you want to make ABSOLUTELY sure that the ONLY oil that goes in that bike's crank case and gear box is specifically intended for use with a "MULTI-PLATE WET CLUTCH" system.....Otherwise a very bad day can be predicted. "Champion Oil" is a reputable brand and preferred thier 2-stroke raceing oil over all else when I raced 250cc class arena-cross. I have since retired from dirt bike racing to take up a much safer and peaceful profession in law enforcement....But I know Champion makes 4-stroke case oil thats compatible with wet clutches....Yama-Lube is ok too...Just make sure you see "Wet Clutch" on the bottle and it's all a matter of consistenly works best for you and preference after that.

Anonymous

  • 71 Answers
  • Posted on Feb 17, 2010

SOURCE: 02 Yamaha xvs 650 dragstar classic that misfires when it warms up

First I would change all the spark plugs, and if that didn't make a difference then it sounds like the coil(s) are warming up and breaking down........when it starts to skip take a good pair of pliers with good rubber on them and pull each spark plug wire, when you get to the one that the running doesn't change then I would replace that particular coil

Anonymous

  • 68 Answers
  • Posted on Feb 25, 2010

SOURCE: 2008 Yamaha raider quick release Windshield mount directions

I looked for instructions everywhere. I saw your complaint on the web. Call the manufacturer and see what they say. Chaz Moto Dc

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Where do I mount my radar detector?

The unit comes with a windshield mount - assemble the bracket ( if needed) and secure to a location on the windshield. Make sure its above the wipers and not behind any metal. Once installed, make sure that the radar detector is LEVEL WITH THE ROAD! This may require bending the bracket to level the unit. (Note: remove detector while adjusting the bracket).
0helpful
1answer

Where is the ignition module in a 99 voyager

Hi Eric:
Also called Ignition Coil, is located at the back of the intake manifold...

2_11_2012_12_07_40_pm.jpg

Fig.: remove the 2 lower ignition coil mounting bracket bolts...


2_11_2012_12_08_55_pm.jpg

Fig.: then remove the ignition coil and mounting bracket together from the engine.

Disengage the wiring harness connector from the ignition coil.
Disconnect the ignition wire from the coil.
Remove the coil mounting bracket bolts, then remove the coil and mounting bracket assembly from the vehicle.
The ignition coil can be separated from the mounting bracket.

To install:

If separated, loosely mount the ignition coil to the mounting bracket.
Loosely install the coil and mounting bracket assembly to the intake manifold. Tighten the coil mounting bracket-to-intake manifold bolts to 115 inch lbs. (13 Nm) and the ignition coil-to-mounting bracket fasteners to 96 inch lbs. (10 Nm).
Connect the ignition wire to the coil.
Engage the wiring harness connector to the ignition coil.
If removed, install the windshield wiper/motor module assembly.
Connect the negative battery cable.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.
1helpful
2answers

How to change the alternator on my 2000 grand voagear

This is for a 3.3L motor
Hope this helps, it it does please leave feedback and vote Thank You and Good Luck

REMOVAL

  1. Release hood latch and open hood.
Removal/Installation of Battery Cables 81929864

  1. Disconnect battery negative cable.
  2. Remove windshield wiper housing, refer to the Windshield Wipers and Washers for proper procedures.
  3. Remove accessory drive belt.
Generator Mounting Bracket 81929870

  1. Remove bolt holding top of generator mount bracket to engine air intake plenum.
  2. Remove bolts holding outside of generator mount bracket to generator mount plate.
  3. Remove bolt holding top of generator to mount bracket.
  4. Remove generator mount bracket from vehicle.
  5. Rotate generator toward rear dash panel.
Generator 81929868

  1. Disconnect the push-in field wire connector . from back of generator.
  2. Remove nut holding B+ wire terminal to back of generator.
  3. Separate B+ terminal from generator.
Generator Pivot Bolt 81929871

  1. Remove bolt holding bottom of generator to lower pivot bracket.
Generator 81929872

  1. Remove generator from vehicle
INSTALLATION

  1. Place generator in position on vehicle.
  2. Install bolt to hold bottom of generator to lower pivot bracket.
  3. Place B+ terminal in position on generator.
  4. Install nut to hold B+ wire terminal to back of generator.
  5. Connect the push-in field wire connector into back of generator.
  6. Rotate generator forward away from dash panel.
  7. Place generator mount bracket in position on vehicle.
  8. Install bolt to hold top of generator to mount bracket.
  9. Install bolts to hold outside of generator mount bracket to generator mount plate.
  10. Install bolt to hold top of generator mount bracket to engine air intake plenum.
  11. Install accessory drive belt.
  12. Install windshield wiper housing, refer to the Windshield Wipers and Washers for proper procedures.
  13. Connect battery negative cable.
  14. Verify generator charge rate.
0helpful
1answer

2008 Yamaha raider quick release Windshield mount directions

I looked for instructions everywhere. I saw your complaint on the web. Call the manufacturer and see what they say. Chaz Moto Dc
0helpful
1answer

Silverado 1500 Z71 off road, 5.3L. Details on fr

This is for the front: Removal & Installation
  1. Remove 2/3 of the brake fluid from the master cylinder.
  2. Remove or disconnect the following:
    • Wheel
    • Caliper. Suspend the caliper from the frame with mechanic's wire. Do not allow the caliper to hang from the brake hose.
    • Caliper mounting bracket bolts
    • Caliper mounting bracket from the steering knuckle assembly
    • Brake pads from the caliper mounting bracket
    • Clips from the inside ends of the caliper mounting bracket and discard
To install:
  1. Install or connect the following:
    • Clips to the inside ends of the caliper mounting bracket
    • Brake pads to the caliper mounting bracket
    • Inner pad (1 wear indicator)
    • Outer pad (2 wear indicators)
    • Caliper mounting bracket to the steering knuckle assembly
  2. Perform the following procedure before installing the caliper mounting bracket bolts:
    • Remove all traces of the original adhesive patch.
    • Clean the threads of the bolt with brake parts cleaner or the equivalent and allow to dry.
    • Apply red Loctite®272 to the threads of the bolt.
  3. Install or connect the following:
    • Caliper mounting bracket bolts to the steering knuckle. Tighten the caliper guide pin bolts to 74 ft. lbs. (100 Nm) on 15 series or 80 ft. lbs. (108 Nm) on 25/35 series.
    • Caliper
    • Tire and wheel assembly
  4. Refill the master cylinder to the proper level with fresh brake fluid. Pump the brake pedal slowly and firmly in order to seat the brake pads. Burnish the brakes as needed.
8helpful
1answer

How to change starter on 2000 chevy silverado

These instructions are for a 5.3L. Unless it is a V6 or diesel, the instructions will be similar if you have a different gas V8.
  1. Disconnect the negative battery cable
  2. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  3. Remove the protective shields as necessary.
  4. Remove the starter solenoid shield.
  5. Remove the starter to transmission close out cover bolt.
  6. Disconnect the engine oil level sensor connection.
  7. Remove the front axle mounting bracket through bolt nut, if equipped with four wheel drive (4WD).
  8. Reposition the front axle mounting bracket through bolt until the bolt tip is flush with the support bushing. Do not remove the bolt, if equipped with 4WD.
  9. Remove the mounting bolts from the engine block.
  10. Slide the starter forward until the starter clears the transmission.
  11. Remove the starter transmission close out cover
    1. Disconnect the positive battery cable and wiring harness from the starter.
    2. Remove the starter from the vehicle.
      1. Connect the positive battery cable to the starter. Tighten Tighten the nut to 16 N.m (12 lb in) .
      2. Install the starter transmission close out cover.
        1. Install the mounting bolts to the engine block. Tighten Tighten the bolts to 50 N.m (37 lb ft) .
        2. Reposition the front axle mounting bracket through bolt until the bolt is fully seated. if equipped with 4WD.
        3. Install the front axle mounting bracket through bolt nut, if equipped with 4WD. Tighten Tighten the nut to 90 N.m (67 lb ft) .
        4. Disconnect the engine oil level sensor connection.
        5. Install the starter to transmission close out cover bolt.
        6. Install the starter solenoid shield.
        7. Install the protective shields as necessary.
        8. Remove the safety stands.
        9. Lower the vehicle.
        10. Connect the negative battery cable. Tighten Tighten the bolts to 17 N.m (13 lb ft) .
2helpful
1answer

Re-assembly of 99 Blazer mirror to windshield

This is a relatively easy task, the bulk of the work has been for you. The rear view mirror assembly simply slides onto that metal block that was glued to your windshield. Your mirror mount (the part that slides onto the metal bracket) may be cut differently or shaped different from the rest of that part. you simply need to line that up with the metal mount on your windshield. slide the mirror on and tighten down the set screw if you have one. I've listed the steps below

1. find the base mount for your mirror (this is the bottom of the mirror that sits on the windshield)

2. look for a cut out or flat part of the mirror base.

3. line the flat part of the mirror base with the metal mount bracket on the windshield.

4. slide the mirror onto the metal bracket (this may require you to wiggle while you slide the mirror onto the metal bracket).

5. tighten the set screw on the mirror base ( this is important because your mirror will vibrate off the bracket if you don't.

Note some mirrors slide from the bottom of metal mount bracket and some slide from the top. it sort of depends on the manufacturer and/or the way the bracket was installed.

Hope this helps
0helpful
2answers

There is a black disc but I do not see any instructions for using it.Does it mount on the windshield?

my Magellen came with a black disk with adhesive on 1 side. Intended to be adhered to any smooth surface (e.g., windshield). The mount for my unit includes a suction cup. So, mount black disk to windshield and attach suction cup to smooth side of black disk. Be sure disk is positioned where suction cup and bracket and GPS will have sufficient room to mount everything.
Not finding what you are looking for?

1,171 views

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

vince

Level 3 Expert

2530 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1212 Answers

littlewheel

Level 2 Expert

122 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...