Motorcycles Logo

Related Topics:

Question about kawasaki Motorcycles

Open Question

I need know where exactly wires go to junction box of my 2007 ninja 250

Color code left to right

Posted by Anonymous on

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

With a 2001 eldorodo etc northstar need to see the wiring want to know where the red wire goes from the battery voltage box

battery voltage box ???? Fuse / relay box ??? underhood / battery junction block ??? There are two fuse boxes under the hood in the engine compartment . one right an one left . One cable from the battery to the right one an one from the right one to the left one .
0helpful
1answer

Can I install a junction box before my water heater junction box?

Junction box is fine.
Must be accessible and not hidden inside wall.
http://waterheatertimer.org/Color-codewire.html
http://waterheatertimer.org/How-to-select-right-wire-nut.html

43 feet is not over 100 feet, so wire size can stay same.
Recommend 30 amp breaker and 10 gauge wire for 4500 watt water heater.
If circuit has 20 amp breaker and 12 gauge wire, recommend 3800 watt elements.
http://waterheatertimer.org/How-to-replace-water-heater-element.html

If you need further help, I’m available over the phone at https://www.6ya.com/expert/gene_9f0ef4df2f9897e7

0helpful
1answer

What color is the taillight wire on the 2007 h3 hummer .

at the tail lights the wire is blue, at the rear light junction block ( under the rear body about the center of the rear bumper ) the right side tail light wire is brown/white the left side tail light wire is brown, from the junction block to the tail lights both wires are blue.
0helpful
1answer

Ok i have a 95 ford aerostar van and i need to hook up a wiring harness to pull a trailer but i need to know the color code for the wiring in the van ????

I'm going to assume that you don't have the tow pkg and need the standard color codes. They are as follows.
left turn sig. yellow
right turn sig. dark green
bu light black w lt. green stripe
parking/running lt's brown w white stripe
ground black.
When splicing the wires I recommend you pick up a small plastic (waterproof) junction box to keep the connections clean
and it's easier to trace a short, any parts store should have this
in kit form for short money.
0helpful
1answer

Radio wiring harness color code for ford van e-250

Car Radio Battery Constant 12v+ Wire: Red/White
Car Radio Accessory Switched 12v+ Wire: Blue
Car Radio Ground Wire: Black/Gray
Left Front Speaker Positive Wire (+): White
Left Front Speaker Negative Wire (-): White/Brown
Right Front Speaker Positive Wire (+): White/Violet
Right Front Speaker Negative Wire (-): White/Orange
Left Rear Speaker Positive Wire (+): White/Green
Left Rear Speaker Negative Wire (-): Brown/Yellow
Right Rear Speaker Positive Wire (+): Brown/White
Right Rear Speaker Negative Wire (-): Brown/Blue
0helpful
1answer

250 ninja dropped on right side at 0mph. signal broken and scratches around signal. how much to repair?

Go to Powersportseast.com and look up your bike on the Parts Fische. It will give prices and you can order thru them if you want. Signals are the cheap part by a long shot! I have been rebuilding a Salvage 08 250 ninja and have had to replace A LOT on it. The plastics alone are around 250-350. If it is really bad on the plastic try Ebay and wait till you find exactly what you need. The signal is around 40 bucks give or take
1helpful
1answer

I need no color code for 2006 ford taurus

+12V DC Battery(Constant) Red/yellow - Control unit in left side of luggage compartment 17 20 amp Junction box in front center of engine compt.

Switched Accessory Red/orange - In-line with the starter relay 27 5 amp Junction box in front center of engine compt.

Ground Black/lt.green

Remote Turn On(output) Brown/orange Pin 8 of CD changer. Also light green/black between rear control unit (C388B-2) and front panel (pin 4).

Illumination See notes *

Left Front + Orange/lt.green

Left Front - Lt.blue/white

Right Front + White/lt.green

Right Front - Dk.green/orange

Left Rear + Grey/lt.blue

Left Rear - Tan/yellow

Right Rear + Orange/red

Right Rear - Brown/pink


Notes
Information listed in the harness section refers (in this case) to the rear control unit in left side of the luggage compartment.

* Illumination is controlled from the integrated control panel, thru dark blue/white at pin 2.

INTEGRATED CONTROL PANEL has white/red for battery input (pin 11), with fuse no. 33 of 15 amps in the junction box under left side of dash; black/pink for acc. power (pin 6), with fuse 22 of 15 amps in the junction box under left side of dash; red/yellow for hot in start or run (pins 5 & 16), with fuse no. 32 of 10 amps in the same location.

AUDIO connections between the integrated control panel (front) and the rear control unit (rear) are as follows:

R+ dark blue/white wire between pin 9 of front unit & pin C388B-7 of rear unit;

R- gray wire between pin 19 of front unit & pin C388B-20 of rear unit;

L+ brown/light green wire between pin 20 of front unit & pin C388B-6 of rear unit;

L- white/pink wire between pin 10 of front unit & pin C388B-19 of rear unit.



AUDIOPHILE SYSTEM has right and left tweeter speakers branching to right and left front speakers with the same colors.


Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.
0helpful
1answer

Hobart Dishwasher electrical connection

Hi chefmail,

I'm Harvey the Master Plumber.

You want to know: Somebody disconnected our AM-14 to redo the floor, and left it disconnected. You know basically where the wires went, but could use some help or a diagram.

I generally don't recomend this to the average homeowner so lets assume you're above average.
Lets also assume that the fellow who removed it knew what he was doing (he should have reinstalled it for you).
If all you need is help with the wireing:
First double check that the power is off.
There should be a romex connector a few inches from the end of the wire. If it's not there he may have left it attached to the junction box under the d/w. You must use a romex connector to connect the wire to the junction box. Make sure the romex connector is on the cover insulation not on the individual wires. The wires are color coded. Connect the blacks together, the whites together and the ground to the green wire (sometimes to a gound screw). Be carefull that the wire nuts are tight but none of the wire ends broke. Before you put the cover on finish instaling the d/w, water line, drain line, counter screws and be carefull to make sure the d/w is perfectly level. Turn on the water and check for leaks. Turn on the power and test the unit. Then put the junction box cover on. All that's left is the kick plate. If you run into problems you might consider utilizing our Repair Directory to find a repairman.

Feel free contact me again!
Please give me a rating here at fixya.com before you sign off
Thank you,
Harvey your Master Plumber
Sep 11, 2008 • Dishwashers
Not finding what you are looking for?

29 views

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

7336 Answers

Marvin
Marvin

Level 3 Expert

85241 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22509 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...