Question about Qlink Sapero 250 Motorcycles

Open Question

Why no spark?

New stator, pick up, CDI, coil, kill switch. Still no spark

Posted by Ronnie Piedra on

Ad

5 Related Answers

Anonymous

  • 7 Answers

SOURCE: no spark

It sounds to me like the repair shop has connected the ignition wire ( the wire going to the + side of the coil ) to the wrong switch terminal. Take a volt ohm meter and connect the ground wire to the negitive ( - ) side of the battery and expose the ignition switch terminals. With the switch in the OFF position check for volatge on all the terminals. Make note of any terminals showing a 12 volt reading. That is probably the feed line from your battery. Turn the switch to the ON or RUN position and check for a terminal other than the one which gave you a reading before. note and mark this terminal. Locate the coil. There are 2 thin ( 18 guage ) wires attached to the coil. One goes to the distributer and the other goes to the ignition switch. Isolate that wire and reattach it to the connection on the ignition switch you marked earlier...
Good luck,
shag79

Posted on Nov 29, 2008

Ad

Anonymous

  • 1 Answer

SOURCE: NO SPARK,110CC, 4 STROKE,NEW STATOR,CDI,AND RECTIFIER

Hey whats up? Try back probing your wires going to the CDI unit with a volt meter or continuity tester to make sure you do have any broken wires. Then check the stater make it is good. If sure how to check the starter take it a bike repair shop they should check it for free.. If that does work let me know and I will look further into it for you. Good Luck.

Posted on May 22, 2009

Ad
ollie reece

ollie reece-jones

  • 1167 Answers

SOURCE: my kx250f has no spark after replacing wire

are you getting power to these items best to check this before you carry anyfurther

Posted on Oct 07, 2009

Benimur

Louie Role

  • 6966 Answers

SOURCE: NO SPARK ON A 98 RM 125

Hi and welcome to FixYa,

Initially, test for the presence / absence of below described voltages using an analog / needle type voltmeter when starting the bike:

  • pulsating low AC voltage coming from the pickup coil;
  • pulsating voltage feeding the ignition coil.

Good luck and thank you for asking FixYa.

Posted on Dec 19, 2009

rigger094

  • 188 Answers

SOURCE: honda crf450 no spark atall plenty of power out of

maybe get a new spark plug.make sure your grounded(earthed). did you take the plug out and check for spark against the motor while you cranked the bike over?

Posted on Oct 17, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will cdi box stop stator from firing on a 125cc pit dirt bike


Stator will stop the cdi from firing the spark plug and either cdi or stator if bad will stop a spark from being created. The coil, wiring, kill switch and other things can also stop ignition spark.

Oct 14, 2015 | Pit Motorcycles

1 Answer

97 blaster has no spark and it has all these new


Stator or coil also could be bad kill switch or ground

I’m happy to assist further over the phone at https://www.6ya.com/expert/joseph_cfbe9ad29efdc8bb

Sep 27, 2014 | Motorcycles

1 Answer

I have a 2010 Oliver City CPI, motor scooter. The engine wont start. The starter seems to work and theres gas in it. Tried the kickstarter and wont start. bad spark plug maybe?


My problem started like this,I found No spark so changed coil,cdi,voltage reg,eventualy found stator at fault,check pick up strip on flywheel and pick up pin on black pick up coil,this is fixed to stator and sends spark signal to cdi,mine were both rusty/dirty,I fitted a new stator,but now have light problems..stator seems to be to strong.

Jul 14, 2011 | 2011 Cpi Oliver City

1 Answer

Changed the CDI, Magneto, and pick up coil, on Kazuma Falcon 90 ATV. Still no spark.please help.


I'm having the same problem with my Kazuma falcon 250. No spark, the stator shows good ohms and I just replaced the CDI box and still nothing. I'll check the kill switch and reverse override.

Apr 29, 2011 | Sport & Outdoor - Others

2 Answers

I have a chance to pik up a 88 yz 125 for a hell of a price and the guy says it wont start. No spark. electrical problem. says its the stator. I dont know that. So im asking, what exactly I can do to find...


hello, usually you have 3 things for firing problems, stator and stator pickup coil, or ign coil, or cdi, i have a 2000 warrior 350, i just went through all that, you can buy after market cdi from procom engineering inc. i purchased one for my warrior 76.00 , it advances timing, hotter spark etc.most of the time it is the stator, pick up coil, both are hooked up together in the stator case, left side of motor,warrior cdi usually goes bad, havent heard of cdi on 88 model, may need to check with dealer.

Feb 06, 2010 | Yamaha YZ 125 Motorcycles

1 Answer

95 Kawasaki 900 zxi, no spark


magneto stator can also be a solution check for AC power from stator while cranking the motor use sta-bil winterizing fluid to insure piston where during cranking process spray directly into spak plug holes with spark plus out 4 sprays into each cylinder should be enough crank motor without plugs for reduced compression and more cranking amps

Jul 21, 2009 | Boating

1 Answer

2006 crf100 no spark


You have 2 basic possibilities,
  • A kill switch is active
  • The ignition control module has gone bad
The stock spark plug is an NGK CR7HSA. Is a kill switch on? Does the side stand have a kill switch? Is it working properly? Check the operation of all kill switches with a volt ohmmeter.

Check the wiring harness. Did a wire come unplugged? Are all wires clean and with solid connections? Any abraded or pinched wires? If still no spark, get CDI system checked at the dealers shop.

A top rating on this answer? Thanks!

May 24, 2009 | 2005 Honda CRF 100 F

2 Answers

Kawasaki kx80 has no spark


hi mate replace wires/cables and put another spark plug in it could be spark plug fouling and try the cdi in another kx80 also replace hd lead from coil to sparky

May 19, 2009 | kawasaki Full Suspension Mountain Bike Men

2 Answers

Yamaha big bear no spark


I'm not familiar with all quads and all the kill switch locations. Does it have a tip-over kill switch? Is it working? Is the quad in neutral? Is the neutral light on? Many engines will not spark if the neutral light is not on. Are the headlights off when starting?

How good is your battery? A low battery can kill spark. Test for spark by grounding the threads of the plug against the cylinder. Have a friend kick the bike while you watch for spark. Assuming no spark, then check all the kill switches with an Ohmmeter to be sure each switch is working properly. Sometimes a switch goes bad. Try disconnecting all kill switches then check spark.

Check the wiring harness, even under the gas tank and seat. Are all the connectors clean and with a tight connection? Any abraded wires? Check the ignition switch also. The switch can go bad as well. Are the flywheel coils good > is the battery getting a charge?

Still no spark? If CDI then get it checked.
If points then file or replace them along with a new condensor and reset the gap then time the engine. >> I hope this helps.

Please rate this answer. Thanks trsrhntr!

Apr 02, 2009 | kawasaki KLX 300 Motorcycles

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Qlink Experts

Arnie Burke
Arnie Burke

Level 3 Expert

6576 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1189 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Are you a Qlink Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...