Question about Power Motorcycles

1 Answer

When i connect batteries to the main box, you know the plug that runs everything, ya so , it sparks and there is no power or ignition please help

Posted by on

  • Gregg Mahin
    Gregg Mahin Dec 02, 2019

    Hi, Rick I would really love to help you with your bike question but due to the magnitude of yesterday's solar flare the batteries in my crystal ball are dead and my mental telepathy headset circuitry was melted. I need the year, make, and model of your motorcycle please click on " Ask For More Information" directly below and provide this information in the box that will open and then click on the green "SEND" box in the bottom right-hand corner after it posts I will receive an "ALERT" icon that will allow me to respond to your information. Good luck and have a wonderful day.

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that has over 10 points.

  • Contributor
  • 11 Answers

Battery backwards. Or normal indicating you're connecting power? It's so7nds like it's running to ground

Posted on Aug 20, 2019

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 2 Answers

SOURCE: HELP ME PLEASE!!!

it didn't work
is there another solution that works?
please help

Posted on Oct 28, 2007

Anonymous

  • 1 Answer

SOURCE: HELP ME PLEASE!!!

ok i followed all the steps till i got up to step one, once i click the link to open the page, it said the link had a error and it relocated me somewhere else.

Posted on Dec 24, 2007

Anonymous

  • 35 Answers

SOURCE: Charging Problems with FUJITSU SIEMENS AMILO PRO V2055

SOunds to me like the charge board inside the laptop has gone bad. If it will not run off of the mains supply without the battery and will not charge the battery, this is your problem. AS far as where you can get the parts or have it repaired. I am unsure of because I would need the full model and make of the laptop which didn't fit in the listing title bar above If you could send me more info, I would be glad to try to help.

Posted on Dec 31, 2008

Anonymous

  • 2 Answers

SOURCE: 2004 Kawasaki Prairie 700 wont start

Never mind guys, i figured it out, the valves actually tightened up and pushed them off their seat, no compression, so i got the feeler guages and fixed it, lots more power now:P thanks anyway.

Posted on Jan 31, 2009

MakisRC51

MakisRC51

  • 408 Answers

SOURCE: still no spark to plugs even after replacing coils.

Either your pulse generator does not give right pulses to the ECU or your ECU need replacement.Find the wires that travel from the pulse gen to the ECU to check them for pulse.

Posted on Jun 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have no fire...checked all the basic options...


Hi, Leisha and the usual suspects are:
1. Fouled spark plugs.
2. Discharged battery, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
3. Loose connection at ignition coil or plug between ignition sensor and module.
4. Spark plug cables in bad condition, shorting / leaking, spark plug cable connections loose.
5. Faulty ignition coil or ignition / electronic module
6. Failed CKP, CMP, or BAS sensor.
7. Faulty ignition switch.
8. Security alarm failing to disarm needs reset
For more information about your issue and valuable free downloads that you will need please visit the websites below. Good luck and have a nice day.
TROUBLE SHOOTING
How to diagnose no spark situation on motorcycle
How to test motorcycle CDI box ignition coil
Testing your motorcycle coil

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e




Mar 03, 2016 | Motorcycles

1 Answer

Suzuki rf400 getting no power to the spark plugs reading here if jump start can damage ignition box or burn out the armature but what armature guidelines please


Hi, Emma never jump start from a running car battery if you have a CKP sensor it needs compression to send the correct signal to the ICM/ECM, make sure both spark plugs are in heads and use a grounded third plug to check for spark or hold spark plug cable close to spark plug in the head. If still not getting spark the usual suspects are:
1. Fouled spark plugs.
2. Discharged battery, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
3. Loose connection at ignition coil or plug between ignition sensor and module.
4. Spark plug cables in bad condition, shorting / leaking, spark plug cable connections loose.
5. Faulty ignition coil or ignition / electronic module
6. Failed CKP, CMP, or BAS sensor.
7. Faulty ignition switch.
8. Security alarm failing to disarm needs reset
For more information about your issue, please visit the websites below. Good luck and have a nice day.
How to diagnose no spark situation on motorcycle
Madass No Spark Test Part 1 wmv http://www.blaigre.com/suzuki-rf-400-service-manual.pdf

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e



Dec 10, 2015 | Suzuki Motorcycles

1 Answer

I have yamaha warrior 350 that has no spark. have changed cdi box, pick up coil, ignition coil, stater, spark plugs basically everything besides wiring harness. has 110lbs compression. i need help.


Hi Cheyenne, if you have a CKP sensor it needs compression to send correct signal to the ICM/ECM, make sure both spark plugs are in heads and use a grounded third plug to check for spark or hold spark plug cable close to spark plug in head. If still not getting spark the usual suspects are:
1. Fouled spark plugs.
2. Battery voltage below 8.7 volts, loose or broken battery cables, check the "NEGATIVE" cable at both ends.
3. Loose connection at ignition coil or plug between ignition sensor and module.
4. Spark plug cables in bad condition, shorting / leaking, spark plug cable connections loose.
5. Faulty ignition coil or ignition / electronic module
6. Failed CKP, CMP, MAP or BAS sensor.
7. Faulty ignition switch.
8. Security alarm failing to disarm.
For more information about your issue, please visit the websites below. Good luck and have a nice day.
Yamaha Motorcycle Service Repair Workshop Manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Oct 10, 2015 | Yamaha Motorcycles

1 Answer

My Yamaha XT 500 has a weak spark and wont start -If I use a BP8ES plug ther is some spark With a BP7ES nothing


Hi, Anonymous and the usual suspects are:
1. Fouled spark plugs.
2. Severely discharged or a damaged battery, should have 12.5 volts or better and be able to pass a load test if necessary.
3. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Loose connection at ignition coil or plug between ignition sensor and CDI box.
5. Spark plug cables in bad condition, shorting / leaking, spark plug cable connections loose, check for spark leakage in the dark.
6. Faulty ignition coil, pick up coil, trigger coil or CDI box testing needs to be checked with an ohmmeter at 70 degrees Fahrenheit
7. Faulty safety switches clutch, kickstand, neutral, off/on etc.
8. Faulty ignition switch.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
xt500 NO SPARK but everything checks out Horizons Unlimited The HUBB
78 xt500 no spark please help Vintage
http://www.carlsalter.com/download.asp?p=2027
http://www.zipware.org/download-zipware.shtml
OEM parts for Yamaha
http://www.effeottoracing.altervista.org/alterpages/files/YamahaXT600XT500EOwnersMaintenanceManual.pdf

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Apr 25, 2014 | 1991 Yamaha XTZ 660

1 Answer

APRILIA CLASSIC 125 WONT SPARK


Hi, Downey if you have a CKP sensor it needs compression to send the correct signal to the ICM/ECM, make sure both spark plugs are in heads and use a grounded third plug to check for spark or hold spark plug cable close to spark plug in the head. If still not getting spark the usual suspects are:
1. Fouled spark plugs.
2. Discharged battery, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
3. Loose connection at ignition coil or plug between ignition sensor and module.
4. Spark plug cables in bad condition, shorting / leaking, spark plug cable connections loose.
5. Faulty ignition coil or ignition / electronic module
6. Failed CKP, CMP, or BAS sensor.
7. Faulty ignition switch.
8. Security alarm failing to disarm.
For more information about your issue, please visit the websites below. Good luck and have a nice day.
https://www.tradebit.com/filesharing.php/search/0/2000+aprilia+classic+125

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Apr 20, 2013 | 2000 Aprilia Classic 125

1 Answer

1997 kawasaki VN 800 Vulcan Classic no spark


Hi, Geri and the usual suspects are:
1. Fouled spark plugs.
2. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead-acid batteries.
3. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Loose connection at ignition coil or plug between ignition sensor and module.
5. Spark plug cables in bad condition, shorting/leaking, spark plug cable connections loose check for spark leakage in the dark.
6. Faulty ignition coil or electronic control module.
7. Faulty pulse coil.
8. Faulty CKP, CMP, or BAS sensor.
9. Faulty ignition switch.
10. Faulty run/off switch
11. Tilt sensor needs a reset.
12. Security alarm failing to disarm needs reset
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://www.kawasakimotorcycle.org/forum/main-lobby/100596-95-kawasaki-vulcan-800-no-spark.html
No Spark Kawasaki Vulcan Forum Vulcan Forums
KAWASAKI VN800 Service Manual
OEM Parts for Kawasaki
1997 Kawasaki Vulcan 800 Classic Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Jun 03, 2012 | 1997 kawasaki VN 800 Vulcan Classic

1 Answer

2003 r6 no spark . i checked the main and ignition fuses, checked and bypassed the kickstand switch. checked the ohms of ignititon coils, crank sensor is working , neutral switch is okay. key ignition...


Hi, Jerrend and the usual suspects are:
1. Fouled spark plugs.
2. Severely discharged or a damaged battery, should have 12.5 volts or better and be able to pass a load test if necessary.
3. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Loose connection at ignition coil or plug between ignition sensor and CDI box.
5. Spark plug cables in bad condition, shorting / leaking, spark plug cable connections loose, check for spark leakage in the dark.
6. Faulty ignition coil, pick up coil, trigger coil or CDI box testing needs to be checked with an ohmmeter at 70 degrees Fahrenheit
7. Faulty safety switches clutch, kickstand, neutral, off/on etc.
8. Faulty ignition switch.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
http://www.r6-forum.com/forums/57-garage-mechanical-help/160041-no-spark.html
How to diagnose no spark situation on motorcycle
2003 2004 Yamaha YZF R6 Service Manual R6 Moto Data Project
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-yz-owners-manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


Oct 01, 2011 | 2003 Yamaha YZF-R6

1 Answer

My Ag200 has a intermittent spark? Any ideas?


Hi, Willie_tuna and the usual suspects are:
1. Fouled spark plugs.
2. Discharged battery, needs to be 12.5 volts or more and be able to pass a proper "LOAD" test, your battery may show 12.5 volts or more but has little or zero amps causing the battery to be faulty and must be replaced, AGM batteries fail in this category more so than lead acid batteries.
3. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Loose connection at ignition coil or plug between ignition sensor and module.
5. Spark plug cables in bad condition, shorting/leaking, spark plug cable connections loose check for spark leakage in the dark.
6. Faulty ignition coil or electronic control module.
7. Faulty CKP, CMP, or BAS sensor.
8. Faulty ignition switch.
9. Tilt sensor needs a reset.
10. Security alarm failing to disarm needs reset
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Help with weak intermittent spark ATVConnection com ATV Enthusiast...
AG200 Central everything about the Yamaha AG200 motorcycle
https://app.box.com/s/udl8cy7wtauah94q1nn66z9hciy7f9ub
OEM parts for Yamaha
https://app.box.com/s/dz2vkvm2w52qqmumf5m8yxe7h58xr8vf

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Sep 07, 2011 | Yamaha Motorcycles

1 Answer

I just dont know how to plug everything with it...Power button comes on if you move the amp...sparks if touches with a a screw....dont know which connections to put where


Black is ground(hook to a bolt going into metal on vehicle). Red is switched power(only on with ignition on). Yellow is power(power even if ignition is off). Blue is amp turn-on(located at radio and sends signal for amp to turn on). It is sparking because you do not have it grounded properly. You can damage your amp and or you car's electrical system....be careful. Always pull a main fuse or disconnect the battery when wiring a car audio system.

Sep 16, 2009 | Boss Car Audio & Video

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Power Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Lawrence Oravetz

Level 3 Expert

10543 Answers

Vernon Taylor

Level 3 Expert

5961 Answers

Are you a Power Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...