Question about 1992 Yamaha FZR 600
1992 Yamaha fzr 600 geneses bogging and in first gear, it is skipping and bat loses power. replaced voltage regulator no change @
Hi, Lizzy engine "BOG" is mainly caused by a rich air and lean fuel condition but it can also be caused by a lean air and rich fuel condition this situation rarely occurs and is only caused by the misinformed weekend warrior that owns a toolbox. If the bike has been sitting for months or years you will have to completely disassemble the carburetor and submerge the parts (except rubber parts) in "Carburetor Dip" It usually comes in a gallon bucket with a wire mesh basket that can be purchased at any automotive store. If it is not the above scenario then the following explanation will apply.
The more you open your throttle the more vacuum you are creating in your carburetor venturi and your intake manifold. When you are operating at higher RPM any unmetered air that leaks into your system can become more obvious.
Unmetered air is the air that is getting into your system after the fuel has been delivered. If you have unmetered air getting into your system between the butterfly/slide of the carburetor and the cylinder head this will create a lean condition.
All of the rubber components of the fuel system like vacuum hoses and intake manifold that you mount the carburetor to are made of rubber. If none of these components has been changed they are more than likely highly degraded and probably cracked in places to allow unwanted-unmetered-contaminated air into the combustion chamber. Check all of your vacuum lines and vacuum plugs for carburetor synchronization. The vacuum plugs are in the head just after the rubber intake manifolds. The petcock has a vacuum line as well as part of the emission system.
1. Check the intake manifold for fissures.
2. Ensure the bands used to tighten the manifolds down on the intake are secure and have not bound up the manifold.
3. Make sure air box fittings are not warped and fit completely over the carburetor.
Your airbox is metering air and is the first step in the process of consuming air and fuel. The system requires the resistance of the air filter in order to get the proper vacuum to "SUCK" the fuel out of the float bowl and create the proper venturi effect.
Improper mounting and sealing of the airbox will create a small lean effect. This might seem like no big deal but you are inviting dust and debris in your engine that is doing slow damage by not having proper fitment. Fix it so you know it's not contributing to your issue. Pick the low-hanging fruit first.
Do not go and start adjusting anything at this point. It ran fine before. There is something wrong with the assembly or a component. Do not adjust your floats. Get it back to where it was. The moment you start tweaking everything is the moment you lose OEM settings which are a must-have for fine-tuning and maximum performance.
Fine-tuning your carburetor and multi carb syncing come at the very end following the proper procedure established by the Carburetor Gods.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Yamaha FZR 600 Service Manual
Posted on Jun 11, 2019
Does the bike have a sidestand switch that cuts the power if the stand is left down? If it does, disconnect it and temporarily join the ends together and try starting....
Posted on Mar 21, 2009
SOURCE: 1994 yamaha fzr 600.
i had a similar problem on my 1998 honda superhawk. I was down in Daytona Beach, Florida, and it was really hot and my battery went dead. It turned out that the heat of being down there along with the frequent short trips and idling we were doing down there fried my regulator/rectifier. It actually melted it was so hot. I bought a new regulator rectifier from a guy online who was really cool about it. Rick's Motorsports Electrics was the name of his store.
I looked up the part for you. check it out: http://www.ricksmotorsportelectrics.com/proddetail.php?prod=10-417&pmc=OTRZYW1GWlI2MDA=
Posted on Aug 19, 2009
Tips for a great answer:
Sep 08, 2012 | 1994 Yamaha FZR 600
Aug 09, 2012 | 1992 Yamaha FZR 600
Aug 04, 2012 | 1992 Yamaha FZR 600
Jul 07, 2012 | 1994 Yamaha FZR 600
Mar 09, 2012 | 1992 Yamaha FZR 600
Mar 27, 2011 | 1992 Yamaha FZR 600
Feb 16, 2011 | 1992 Yamaha FZR 600
Apr 28, 2009 | 1992 Yamaha FZR 600
Apr 26, 2009 | 1991 Yamaha FZR 600
Mar 20, 2009 | 1994 Yamaha FZR 600
Aug 08, 2013 | Motorcycles
456 people viewed this question
Usually answered in minutes!