Question about Motorcycles

1 Answer

Roadking 2007 wiring color code

I want know what Is the color code cause I want extand my handlebar

Posted by Steeve Bouchard on


1 Answer

Dan E

  • Level 1:

    An expert who has achieved level 1.


    An expert that got 5 achievements.


    Visited the website for 3 consecutive days.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 31 Answers

You don't need to know what the wires are used for. Just make sure to use the same gauge wire and to waterproof your connections.

Posted on Apr 28, 2019


2 Related Answers


Rob Stephenson

  • 284 Answers

SOURCE: needing diagram of how to tighten handlebars on motorcycle

You have to remove the headlight, then the Nacelle ( passing lamps if you have them ) Under the lock ( which is removed with a small flat head screwdriver ( it's held in by 3 little push in tabs ) There are 2 phillips head screws( remove them ) then once you have the headlight out, there is a 5/16 nut holding the top chrome spine in place. Remove the nut lift the spline. then remove the nacelle one side at a time. Once you remove the nacelle the 1/4 allen bolts are right there to tighten. Make sure you tighten them evenly. Reverse steps to re-install back to normal.

I’m happy to assist further over the phone at

Posted on Aug 27, 2009



  • 8 Answers

SOURCE: color of power wire on 2005 handlebar controls

wire is white with a black strip will be your hot

Posted on Apr 12, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer


Hi, Bruce if you have TWB it may be an issue but after careful deliberation 4 out 5 Harley Gods give this one a thumbs up, but just to be on the safe side you should give your local dealer's parts/service department a call to confirm. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below and for more specific information or questions at no charge please feel free to contact me at [email protected] Good luck and have nice a day.
Heritage Handlebars on Road King Harley Davidson Forums
Harley Davidson Manuals Mark Workshop
Instant Tech Relief A must have !!! only $6 a month "CHEAP"

Aug 10, 2016 | 2007 Harley Davidson FLHRC Road King...

1 Answer

2007 Nissan Altima Stereo Wiring Diagram for Bose Navigation

None are actually color coded. The schematic has the wire colors on it next to the wire.

May 01, 2014 | 2007 Nissan Altima 3.5 Sedan

1 Answer

What are wire colors for handlebar switches

Hi Anonymous, for a free wiring diagram please visit the website below and good luck.
Harley Davidson Wiring Diagrams and Schematics

Btw, I’m available to help over the phone in case u need at

Nov 08, 2013 | 2006 Harley Davidson FXDWGI Dyna Wide...

1 Answer

2007 roadking high beam indicator light stays on

Hi Myles, check continuity at your hi/low beam switch. Good luck and have nice day.

Btw, I’m available to help over the phone in case u need at

Mar 28, 2012 | Harley Davidson Motorcycles

1 Answer

When I turn my RoadKing on, the turns lights ( both) flah quickly 6 time. I cannot start the engine with the handlebar start button

Sounds like the security alarm on your bike is tripping. You should have a code to enter or you can reset it. I hope this helps.

Jul 03, 2011 | 2000 Harley Davidson FLHR-FLHRI Road king

1 Answer

My 2002 roadking handlebars are loose any fix

Harley Davidson handlebars are mounted in rubber vibration dampers. If they're too "mushy" for you, you can replace the bushings with either neoprene bushings or solid bushings. On your road king you need to gain access to the bottom side of the upper triple tree.

Apr 05, 2010 | 2005 Harley Davidson FLHR - FLHRI Road...

1 Answer

My handle bars are loose on my 2005 Harley Roadking FLHRI, how do I tighten them. Do I need to remove the headlight assembly?

They're probably not loose. The movement you're feeling is probably in the rubber bushing that the handlebars are mounted in. Harley has used rubber bushings for years to isolate the handlebars from as much engine and road vibration as possible.

On your "cruiser" bikes like your roadking, the bushing are quite soft to dampen the vibration to a greater degree. The bushing on the Softail may not be as soft. The good news is that they aren't difficult to replace with a firmer set. You will have to take the headlight nachelle off to gain access to the nuts or bolts that hold them in place. You can order aftermarket bushings that are more firm or you can even get solid steel bushings to eliminate the movement to the degree that you want.

Jan 08, 2010 | 2005 Harley Davidson FLHR - FLHRI Road...

1 Answer

Rewireing 93 harley davidson FXLR to 96 Handle bar

On the handlebar switches, Harley hasn't changed the color code scheme very much over the years but you really need a good schematic to know exactly how they are wired up. If you can find either a Harley service manual for a 96 model or a Clymer's manual, it would be helpful. I have a schmatic for a 94 FXDWG that should be alright for your 93 FXR but you need a schmatic for a 96 model bike.

Oct 07, 2009 | 2000 Harley Davidson FXD Dyna Super Glide

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

6385 Answers


Level 3 Expert

85239 Answers

richard libby

Level 2 Expert

209 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides