Question about Kymco Motorcycles
You've got a Ignition System Issue which narrows things down quite a bit. It's either the ignition switch that your key goes into, or an on/off(run/stop) switch, or it's a relay for the ignition systems(or starter relay), if it's none of those then it's the starter solenoid that you've been jumping with the screwdriver, it sounds like the starter is working as it should since it turns over- the reason it turns over but won't actually run is because the ignition system won't work unless the key is inserted and in the run position, or if there's any other on/off switch that controls your engine it could be there. I'm not familiar with this exact bike but this is a common issue with all motorized machines! You can bypass all of this but that requires running some wires and a couple of switches plus a relay or two- that's an option but don't do that as your issue is nothing major and would be easier to fix than to go through the trouble of re-wiring it all. Just start troubleshooting and eliminate one part at a time, check relays, fuses, and electrical connections first, then the individual components I listed above and check to make sure they have power coming in and out when/where they're supposed to. If your bike turns over but won't run and the key is on, and you have a functional Ignition system then you need to verify you have ignition by checking your coil's output. EASIEST way to do so is pull a spark plug and connect it to the spark plug wire as you normally would, then hold the spark plug against the engine to ground it and turn it over- you'll see if you have any spark jumping aroundbetween the spark plug's electrode and the base of the plug itself. Either way, you'll get this figured out now that you know where to start and what to check!
Posted on Feb 27, 2019
SOURCE: Oil filter position
The oil filter is underneath the bike in the front where the large square gray oil pan is located. There are two bolts. One is surrounded by a large circle which is about the size of your new oil filter. Remove the bolt and there will be a small washer then the circular metal plate which cups the oil filter. This has a gasket which seals against leaks and inside of the cupped metal plate is the oil filter. Remove replace, and reinstall the parts in the same order. ,,,
Posted on Nov 10, 2008
One of the member/dealer/mechanic owners at PIWYR will have the answer to this.
Probably pops or tony_dt http://www.piwyr.co.cc
Posted on Dec 31, 2008
Loose the gas additive. Clean the air filter and then install new spark plugs. If the bike has carbs, drain the carbs. .... All fixed!
Could you take a moment and rate my answer? Thanks!
Posted on Sep 21, 2009
SOURCE: i turn the key and
a 1997 c1500 doesnt have a carb it is fuel injected, you poured fuel into the throttle body. when you turn the key to the start position and you do not hear the fuel pump you could have a blown fuse. if not, all chevys have passlock a passive antitheft system that have locked the fuel system down. check some remote start companies on the internet you will find one with a wiring diagram, you can figure out the rest from there. its eas
help from the BIG BRAIN
Posted on Jan 14, 2011
Tips for a great answer:
Oct 12, 2018 | 2009 Kymco Venox 250
Sep 16, 2018 | 2003 Kymco Venox 250
May 17, 2018 | 2009 Kymco Venox 250
Sep 13, 2017 | 2009 Kymco Venox 250
Jul 24, 2017 | 2005 Kymco Venox 250
Aug 17, 2011 | 2003 Kymco Venox 250
Mar 07, 2011 | 2003 Kymco Venox 250
Oct 12, 2017 | 2003 Kymco Venox 250
Dec 09, 2009 | 2003 Kymco Venox 250
Sep 21, 2009 | 2003 Kymco Venox 250
40 people viewed this question
Usually answered in minutes!