Question about Suzuki Motorcycles

1 Answer

Is it possible to change the full plastic body on a burgman 2007?

From for a burgman 2017 is the frame is same or not? I know the plastic is not exactly same but is it possible it bolts at the same place? Thank you.

Posted by Anonymous on


1 Answer

Derrick Schultz

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Suzuki Master
  • 11,405 Answers

I got this free Pdf manual from an online store for free and I don't think Ive visited a mechanic or fixya for help for more than 3-4 times out of the all the times I fixed the chipper in these 4 years

Posted on Jan 30, 2019


3 Related Answers


Phil Lovisek

  • 726 Answers

SOURCE: I need to replace two

The gas tank protector is held by 2 clips and 10mm nut. Clips are push in style. You can unlock the clip, by pulling the middle of the clip up. Kinda hard to do without a special tool. The clips are available at Nissan dealer, for about $3 a piece.

Posted on Jul 21, 2008



  • 1 Answer

SOURCE: my fuel sensor does not work it stays at the ful mark

The voltage regulator may be defective. Do all the guages work?

Posted on Oct 17, 2008


  • 92 Answers

SOURCE: 1985 Chevy Monte Carlo, need body info.

the complete nose up to the front doors are bolted on.the only thing that gets a little tricky is the lower radiator support. just take youre time and it can be all disassembled and rebolted with out too much trouble.
good luck chris

Posted on Mar 15, 2009

Add Your Answer


Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have the frame of a 6465 tank car and a possibility to purchase a plastic lionel lines black tank car body. How do I affix it to the frame???

If there are mounting holes on the supports for the tank body,
measure the distance between the centers, and compare them to the mounting holes on the on the frame. If they are the same, just use screws to mount the tank, If the holes do not match, you'll have to drill new ones and then mount the tank body to the car.

Jan 22, 2013 | Lionel Sunoco 6465 Tank Car

1 Answer

Where is the full line located for oil on the 2007 650 suzuki burgman?

take off the left plastic floorboard and there should be a round oil fill window just fill and look in the window and fill it till you almost pass the top of the window...tip make sure the bike is level it canot lean at all or you will over fill it...let me know if it helps it is located right where the arrow points good luck hope this helps oilchange3_1.jpg

Jun 03, 2011 | Suzuki Scooty Streak Motorcycles

2 Answers

Just bought an "04 Burgman 400. Idles rough and

i would say that the carb settings are wrong sounds like the tick over screw is to far in do you know how to adjust this?

if not give me a shout and i will find a manual and tell you


Feb 02, 2011 | 2003 Suzuki AN 400 Burgman

3 Answers

Trying to find the location of the fuel filter on 2000 gmc jimmy, tks!

Hi the fuel filter is located under neath the body at the b post on the inside of the frame. one end will have a flair nut and the other will have a plastic quick connector. unscrew the flair nut from the backside of the filter and then carefully depress the tabs on the plastic connector and pull it apart. hope this helps you

let me know if you need further assistance ok

please rate this solution as i have a whole page of unrated posts, thanks

Aug 30, 2010 | 2000 GMC Jimmy

1 Answer

Driver side electric window fell. How can it be fixed

Body shop guys can take off the door panel re attatch the window cable to the window frame possibly its one of those plastic link cables to raise your window But its kinda complcated to work that mechanism I would just see if the cable is broken on the window frame in the door frame

Jun 22, 2010 | 2004 Ford F150

2 Answers

Im changing the transmission oil 10w40. The manuel says to put in about 13ounces but the dealer told me to fill until it overflows out the filler hole. I've put in almost a full liter(canadian) and its...

The transmission fill hole is a 10 mm bolt that sticks out about 2" the run out of the hole is a 14mm bolt an 1"1/2 below that. it looks like a bolt to hold on the clutch cover.
I had the same problem till I read the service manual.
Ron W.

Jul 09, 2009 | 2003 Suzuki AN 650 Burgman

3 Answers

Where can i get a workshop/service manual for a 2006 burgman 125?

Give it try here. I ain't sure about the language but might be of some help to you.I ain't sure about whether it is 2006 or 2009 but it says burgman 125. Will come up with a better one once I find one.

May 29, 2009 | 2003 Suzuki UH 125 Burgman

2 Answers

Suzuki burgman 650 won,t change gear

I had the same problem until I found out that when you put the Burgman on it's center stand, it pushes a small round metal pin (spring loaded or something similar) that limits the Burgman to 1st gear only. Some kind of safety feature, I guess. You can see the little switch if you put the bike on it's side-stand, get down on the right hand of the bike and look where the centre stand meets with the body of the bike. My switch was stuck in permanent "on" so I just pulled the pin to it's full extention with a pair of pliars, then cut it with a junior hacksaw.

Mar 28, 2009 | 2003 Suzuki AN 650 Burgman

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts


Level 3 Expert

85239 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

6528 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

217 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides