We lost our only key to our 2009 Bashan model TPGS-805 moped, where can we get a replacement key to get into the gas tank and seat?

Two duplicate posts deleted! Refresh page to see your post published.

'year make model cc' in all questions!

So we GUESS!

https://www.google.com/search?q=ignition+timing+on+a+2009+150cc+engine+of+a+moped

..

Kawasaki Motorcycle Wiring Diagrams

www.classiccycles.org/1852/597943.html

Kawasaki BN125 Eliminator 125 Electrical Wiring Harness Diagram Schematic HERE... Kawasaki GPX600 Ninja GPX 600 Electrical Wiring Harness Diagram ...Missing: tpgs

Kawasaki Motorcycle Service Manuals

www.classiccycles.org/1852/1894.html

Kawasaki BN125 Eliminator BN 125 Workshop Service Repair Manual HERE ...Kawasaki GPX600 Ninja 600 Electrical Wiring Diagram Schematic 1988 to 1991 ...Missing: tpgs

WIRING DIAGRAM thread for all sorts of bikes - Bike Chat Forums

www.bikechatforums.com/viewtopic.php?p=2322761

Oct 11, 2009 - 25 posts - ‎7 authors
this is the new wiring diagram thread, requests allowed .... http://i574.photobucket.com/albums/ss182/hmmmnz1/Honda/th_cb600f.jpgCB600f ...Missing: tpgs

Remove casing on nearside of engine, the one where the kick start is. The kick start will come off with the casing, now you will see the belt, remove the bolt on the front pulley which will split and the belt can be removed, while the front pulley is split it might be an idea to replace the friction cones (relative low cost). If the cones are worn it will affect the performance.

alternator is bad.

Hi Gina,
Can we have the make and model of you moped so we could help you more?

You may also see this, just in case it is the same moped as yours.

regards,
Jeep Brainy

http://www.partsprousa.com/?vehicle_type=Scooter&brand=Bashan&brand_model=TPGS-811B&srch=2#searcharea

You didnt say if it is a cruiser or street so here is both:

1. Cruiser
   • 1 Remove the seat from your motorcycle. Turn the key to the "On" position and hold it there as you lift up on the seat to unlock it.
     
   • 2 Put on the gloves and the safety glasses. Remove the plastic cover on the battery compartment.
     
   • 3 Detach the cables connected to the terminals on the top of the battery. You can pull the cables off by hand. Remove the negative (black) cable first, then the positive (red) cable. Cover the negative battery terminal with black electrical tape.
     
   • 4 Lift the battery out of the compartment. Be sure not to touch the terminals to any metal components of the frame or the seat.
     
   • 5 Position the new battery. Connect the positive cable to the battery first, then the negative cable.
     
   • 6 Reattach the seat.
     
   Street Bike
   • 1 Lift or remove the seat on your bike. Use the ignition key to unlock the mechanism holding the seat in place. Depending on the model, tilt the seat back or lift it completely off the bike.
     
   • 2 Locate the two anchor bolts on either side of the gas tank. Unscrew the bolts using an Allen wrench. Hold on to both the bolts and the bushings on the underside of the bolts. The bushings prevent your gas tank from rattling during operation.
     
   • 3 Tilt your gas tank up to reveal the battery compartment. It is necessary to prop up the gas tank or have a helper hold it for you as you work on the battery.
     
   • 4 Detach the cables connected to the battery terminals. Remove the negative (black) cable first, then the positive (red) cable. Cover the negative battery terminal with black electrical tape.
     
   • 5 Lift the battery out of the bike, being careful not to touch the terminals to any part of the motorcycle or your skin.
     
   • 6 Position the new battery in the bike. Connect the positive cable to the battery first, then the negative cable.
     
   • 7 Reposition the gas tank and secure it by tightening the bolts.
     
   • 8 Close or reattach the seat
     

If you need further help, reach me via phone at https://www.6ya.com/expert/john_31c836b20f0c2290

were both keys the same if not it sounds like its had a replacement ignition barrel. it may have a key number stamped in the back of the barrel casing. if it has you can order a replacement key from any good locksmith/dealer, alternatively you can order a replacement barrel from m&p or any motorcycle parts stockists.

It sounds lke you have water in the gas

remove /replace gas in tank