Question about Suzuki Motorcycles

1972 Suzuki 185 cylinder head torque - Suzuki Motorcycles

5 Related Answers

Greg Bernett

2989 Answers

SOURCE: cylinder head torque settings 1990 2.6L isuzu motor

From front to back is this:

7 3 1 5 9

8 4 2 6 10

First torque value is 58 ft lbs.....then final torgue is 72 ft lbs.

Posted on Mar 21, 2009

Anonymous

462 Answers

SOURCE: what torque spec for chev aveo 2004 cylinder head

18 lb ft+60°+60°+60°+10°

NEW HEAD BOLTS ARE REQUIRED WHEN REPLACING THE HEAD OR HEAD GASKET.

Posted on Jul 04, 2009

johnz1313

88 Answers

SOURCE: Hi I'm looking for cylinder head torque settings for a 1992 BMW 316/318 e36

BMW cylinder torque setting all models

According to my service manual as follows.

Cyl head to engine block (torx e12 M10 bolts)

Stage 1 30nm (22 ft – lb)
Stage 2 + 90 degrees
Stage 3 + 90 degrees

Cyl head to lower timing chain cover 10nm (89in – lb)

The tightening sequence is from inside to outside crossover as normal. Loosening sequence is from outside to inside crossover. Remember to set torque wrench at low setting and work gradually up through the whole sequence until you get the desired torque.

Posted on Aug 29, 2009

Chris Biddle

233 Answers

SOURCE: 94 mazda B3000 3.0L cylinder head torque specs

Step 1 torque to 59 ft pounds
2. Loosen one full turn
3. 37 ft pounds
4. 68 ft pounds

Use torque sequence below

Posted on Sep 17, 2009

Anonymous

122 Answers

SOURCE: need cylinder head gasket torque specs.

looks like there is special sequence to reassemble and tightening, a quick note replace any bolts that have two punch marks.tighten as follows: x x x x x 10 4 2 6 8 x x x x x 7 5 1 3 9 torque all down to 15 ft lbs torque to 30 ft lbs plus 90 degrees. Good luck!

Posted on Sep 18, 2009

Add Your Answer

Upload

Upload an image from your computer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

1 Answer

The torque settings for the cylinder head on my briggs and Stratton single cylinder 12 hp model 283707 model lawnmower engine

Hi cylinder head 185 In.Lbs.cheers

Sep 25, 2016 | Garden

1 Answer

I need the head bolt torque specs and sequence for a 2008 Suzuki reno 4 cylinder

well it's at alldata.com and at suzuki pitstop plus dot com.
here ill do that for you....
4 banger no displacement stated, now that is a challenge.

now the words..... USA car... 2.0L vin Z

Cylinder head bolts. Tighten the cylinder head bolts gradually and in the sequence shown. Tighten the cylinder head bolts to 18 ft. lbs. (25 Nm) and turn the bolts another 3 turns of 90 degrees using the angular torque gauge KM-470-B.

Jun 17, 2015 | 2008 Suzuki Reno

1 Answer

What is the cylinder head bolt torque pattern on a 2007 suzuki forenza

post engine size. they use like 6 engines.
open hood, look up , see that EPA tag, it says right there.
no man on earth can guess engines. not ever.
(sure, rare exeptions, on 2 door sports cars)

Aug 20, 2014 | 2007 Suzuki Forenza

1 Answer

Whats is te cylinder heads torque for suzuki aerio 2.3 lts

Hi! Please don't forget to rate! Thanks!

Cylinder head bolt torque sequence-2.0L and 2.3L engines

Apply engine oil to the bolt threads and tighten the cylinder head bolts, in sequence, using the following 6 Steps:

Step 1: 38.5 ft. lbs. (53 Nm)
Step 2: 61 ft. lbs. (84 Nm)
Step 3: Loosen all of the cylinder head bolts
Step 4: 38.5 ft. lbs. (53 Nm)
Step 5: 76 ft. lbs. (105 Nm)
Step 6: Bolt M6 (bottom left of cylinder head) - 8 ft. lbs. (11 Nm)

May 12, 2011 | 2003 Suzuki Aerio

1 Answer

What is the right Torque Specification of the cylinder head bolt,main bearing and connecting rod bearing for a 1997 Ford F 150 4.2 liter? Thank you...

Cylinder heat bolt torque:
Torque sequence --------- front | 7 3 1 5 | | 8 4 2 6 | --------- Step 1: Torque all bolts in sequence to 14 Ft/Lbs Step 2: Torque all bolts in sequence to 29 Ft/Lbs Step 3: Torque all bolts in sequence to 36 Ft/Lbs Step 4: in the sequence, loosen the cylinder head bolts three turns. Step 5: Tighten short bolt to 15 - 32 Ft/Lbs Step 6: Tighten long bolt to 30 - 36 Ft/Lbs Step 7: Tighten all bolt to 175- 185 degree note: Do not loosen all of the cylinder head bolts at one time. Each cylinder head bolt must be loosened and the final tightening prior on the next bolt in the sequence.
Main bearing torque:
Torque sequence: Step 1: torque bolts to 91 Ft/Lbs with the exception of the rear main bearing cap Step 2: torque rear main bearing cap bolts to 88 Ft/Lbs Step 3: torque brace bolts to 40 Ft/Lbs
Connecting rod torque:
Torque sequence Step 1: Torque to 29 Ft/Lbs Step 2: Turn an additional 90 degrees

May 17, 2010 | 1997 Ford F150 Regular Cab

1 Answer