Question about 2004 Suzuki GSX-R 1000

Open Question

2004 Suzuki GSX-R 1000 how to replace the clutch

The clutch on my 2004 gsxr 1000 won't engage or disengage after replacing and when I try to put the bike into gear it dies...help! @

Posted by Eric Ott on

Ad

5 Related Answers

Anonymous

  • 2336 Answers

SOURCE: 1100 wierd clutch disengage problem

Bleed your slave cylinder on the sprocket cover and refill the hydraulic fluid. If you have any leaks you will get air in the system and it will not fully disengage the clutch. As for the 750, they have cable clutches and you just need to adjust the slack of the cable.

Posted on Nov 20, 2008

Ad
co7196

Ned C Cook

  • 3433 Answers

SOURCE: clutch wont disengage properly

What kind of oil is in the crankcase? Wet clutches take a sprcial oil, noy motor oil. If oil is correct, Is the cable and release levers fully disengaging the clutch? There is an adjustment for the rod inside the clutcjh hub . That could be short stroking.

Posted on May 17, 2009

Ad
ollie reece

ollie reece-jones

  • 1167 Answers

SOURCE: I have a 2000 GSXR 600 and i just finished

hi mate adjust the clutch cable when you put it into gears the clutch is still grabbing so it needs to be adjusted

Posted on Jul 08, 2009

sisadsl

gavin jones

  • 1508 Answers

SOURCE: I put the bike in gear but when i pull the clutch

if the clutch lever feels it has plenty of tension, it may just be the clutch plates stuck together from sitting.

Roll start it and ride around while holding in the clutch, vary the throttle, and they usually unstick. Give it an oil change when it warms up.

Posted on May 29, 2010

Michael Green

  • 3799 Answers

SOURCE: What's your problem?1995 yamaha virago 1100 that sometimes you you put into gear and immediately dies

The Clutch on some bikes will disengage the starter motor. Yamaha will not allow you to engage gear when the side stand is down. Hope this gives you some idea

Posted on Nov 27, 2011

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1984yamaha virago 1000. with the bike running, when I try to shift from neutral to first gear the bike stalls. I think it has something to do with the electrical.. Help!


If you are at idle, in neutral, with the clutch lever pulled all the way in, and you shift into gear and the engine dies, it is likely the switch at the clutch lever. When they fail the bike does not get the signal that the clutch is disengaged and it is safe to shift into gear. Have that switch checked. Some bikes also have a side stand switch, make sure your side stand is always up before putting you bike into gear.

MGM

Sep 13, 2013 | Yamaha Motorcycles

1 Answer

Idle and clutch issue


main jet blocked and clutch damage maybe bent clutch push rod or plates seized together

Feb 19, 2013 | 1991 Yamaha FZR 1000

Not finding what you are looking for?
2004 Suzuki GSX-R 1000 Logo

Related Topics:

282 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

6480 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

217 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...