Question about 2003 Kymco Hipster 125

Open Question

2002 Kymco Hipster 125 how to remove the rusted exhaust bolts

How do I remove the sheared off exhaust bolts from my 2002 125 kymco hipster @

Posted by John Mark edwards on

Ad

5 Related Answers

Rich

  • 2 Answers

SOURCE: battery removal

hi,

Remove the plastic panel on the left side of the bike just under the seat and you will see the battery. unscrew the metal bar that holds it in and simply slide the battery out.

Posted on Mar 06, 2009

Ad

jdthefixer

  • 747 Answers

SOURCE: Removing rusted nuts from bolts to replace toilet seat

Try:

* Penetrating oil...let it soak at least 1/2 hour

* If the nut is stripped, try either grabbing it with vice grips

* If all else fails, either grind it off, or use a nut splitter. Nylon is pretty soft, so it should be relatively easy to break

Posted on Apr 28, 2009

Ad
co7196

Ned C Cook

  • 3433 Answers

SOURCE: Broken manifold bolts / manifold removal

Whatever it takes, but make sure you soak some penetrating oil oi wd40 on others to avoid any more being broken. Pulling the manifold is the safest and quickest way. With it out of the way, you'll have someting on the broken bots, now studs to work with. Always drill a broken stud or bolt clean through. Penetrating oil can work from both ends and a broken easy out can be driven in far enough to work arounf -Good Luck, force nothing, Tap stud and apply only stesdy even presure when extracting.

Posted on May 19, 2009

Anonymous

  • 242 Answers

SOURCE: Exhaust removal required to drop transmission on 92 Ford Ranger?

Yes you do. trust me you don't want to get that thing half way out and down and not be able to continue. Soak those rusted exhaust studs in a good penetrating oil over night. I bet they come right out. I would not recomend cutting the pipe.

Posted on Aug 27, 2009

alicantecoli

Colin Stickland

  • 22485 Answers

SOURCE: 2002 Kia Sedona -- I'm trying to remove the trim

remove the interior panel

Posted on Sep 15, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WHAT IS IGNITION FUSE SIZE ON 125 KYMCO HIPSTER 2005


Battery Fuse : 20A Reserve Fuse :15A Headlight Fuse : 15A Radiator Fan Fuse : 10A All Electric Power Fuse :15A

15 amp

Apr 10, 2015 | 2004 Kymco Hipster 125

1 Answer

Kymco hipster 125cc service manual free


potrzeb?je insterukcie obs?ugi do kymco hipster 125

Mar 25, 2012 | 2003 Kymco Hipster 125

1 Answer

Derestrict kymco hipster 125cc


The answer (rather late :P) is Yes! You can buy a derestricted CDI from somewhere like wemoto.com I expect, which helps with the top end speed. You can also up or downgear the bike. I've got 4 teeth less on my 2001 Hipster (rear sprocket) and I can accelerate like a ***** (faster than most boy racers off the line) and easily outstrip bikes like the 2012 YBF125 and the 2002 CBR125 on the strip. That's all I've done (other than freeing up the exhaust by shoving a screwdriver down the little holes at the end of the exhaust and smacking it with a hammer - sounds deeper too) and take the side off of the air box filter and put a cleaning sponge in place of the original filter (That warbles quite nicely too)

Mar 24, 2012 | 2004 Kymco Hipster 125

1 Answer

Hi . where is the valve timing mark on my kymco-125 hipster cam -sprocket.


the valve timing mark is on the flywheel on the Hipster's.

Remove the large flat blade screw from the top of the left hand side casing. Turn the engine either by hand (using kickstart with ignition off), turning rear wheel in gear, or by removing the "kymco" badge with three 8mm bolts and using a 19mm deep socket on the crank, until you see two marks (one says F one say T) the F one is the advance firing mark, the T mark is the timing mark. Keep turning the engine over and watch your valves, wait for the exhaust valve to close, inlet valve to open and then close again then the next time you see the T line will be TDC. This is where you set your valve timing from.

Oct 06, 2010 | 2002 Kymco Hipster 125

2 Answers

Does the small fuel pump under the tank push out a constant flow or intermitant , bike been stood for 18mth got good electrics but cant to get a contstant flow to the carb


drain old fuel first and replace with fresh,then check fuel filter,carbs need to be cleaned after sitting so long, yes there should be a constant flow of fuel

Nov 26, 2009 | 2003 Kymco Hipster 125

2 Answers

Battery keeps loosing charge- kymco cruiser 125, 2005


I had this exact same problem on a hipster 125, it was a faulty regulator module ( mounted under the seat) I also found a short circuit (somewhere) in the wiring loom between the regulator output and the chassis (probably what killed the regulator in the first place!) I cut and replaced the entire wire to save removing most of the loom and after testing reg to ensure it was dead i fitted a new one (about £60) bike charges and runs like a dream now even with fully lights approx 80% of the time. good luck

Jul 14, 2009 | 2005 Kymco Hipster 125

1 Answer

Battery removal


hi,

Remove the plastic panel on the left side of the bike just under the seat and you will see the battery. unscrew the metal bar that holds it in and simply slide the battery out.

Dec 11, 2008 | 2003 Kymco Hipster 125

Not finding what you are looking for?
2003 Kymco Hipster 125 Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kymco Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

6576 Answers

Are you a Kymco Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...