Question about Kymco Motorcycles

Open Question

What is my problem with my kymco if water is getting on my piston on my kymco super9lc

Posted by Eric Ingram on


Add Your Answer


Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

The location of cam sprockets were the marks should point when piston is at TDC on a 2000 kymco venox motorcycle

Hey Scott.. not sure of the marks.. BUT the cam lobes should be opposite of the rocker arms or buckets,,, ON TDC on the COMPRESSION STROKE<<

Jul 24, 2017 | Kymco Motorcycles

1 Answer

Kymco people 125cc engine seized , can it be repaired

Yes a new piston and a rebore of the cylinder if that is the problem. You will need to tear it down to inspect what caused the problem.

Jan 10, 2017 | Kymco Motorcycles

1 Answer

Does anybody know where I can get a head cylinder for a 2007 kymco venox 250cc

Try eBay or a motorcycle part finder site
And on the problem of it reoccurring difficult to say as need to know what damage was caused to piston and valves
Was it just one rocker arm that broke or is the other damaged did the timing jump and piston hit open valves driving them up and breaking arm and damaging cam shaft lobes
You really need to find out why and how it happened
As it may require a complete timing system replacement on that cylinder cam shafts , rocker arms , valves ,drive sprockets top and bottom , drive chain and a piston

Sep 01, 2015 | 2007 Kymco Venox 250

1 Answer

Where to buy/order spare parts of kymco-spike 125?

I searchedkymco spike 125 and found a number of possible hits very easily. Go to wemotor. com/bikes/kymco/spike 125.. This looks like a possible one.

Jun 17, 2015 | Motorcycles

1 Answer

How do i fix the compression on my 50cc kymco agility

If it is a 2 cycle, I'm not familiar with kymco, the only way to fix the compression is to replace the piston rings and/or piston. It is not uncommon to burn a hole in a piston if the carberator is gummed up. If it is a 4 cycle (probably isn't) you could have a burnt, warped, or sticking valve. Either one it requires taking the head off for further evaluation.

Oct 21, 2014 | 2011 Kymco Agility 50

2 Answers

Does the small fuel pump under the tank push out a constant flow or intermitant , bike been stood for 18mth got good electrics but cant to get a contstant flow to the carb

drain old fuel first and replace with fresh,then check fuel filter,carbs need to be cleaned after sitting so long, yes there should be a constant flow of fuel

Nov 26, 2009 | 2003 Kymco Hipster 125

2 Answers

Erratic water gauge on kymco xciting 300 ri

Hi apexmt; You are right to question it's behaviour.. Somthing is wrong.It should get to normal operating temp. as soon as posible, and stay there. It's piston will not get to the correct size and shape till that happens. It seems (from a remote view point) that it's thermostat is a bit sticky. May I suggest that you have it replaced as a matter of urgency; as : "if the engine is too cold, it WILL WEAR OUT in no time at all". .And ..if the thermostat sticks in the closed position.. it will cook the engine. I do not know your machine ... yet, If you feel competent..... find its radiator...the top hose will more than likely lead you to its thermostat housing. Do this cold. Drain the coolant system. remove the housing and replace the thermostat. Do NOT put its radiator cap back on until it's reached operating temp.The top hose will get hot as the thermostat starts to open. So You Know for sure that it is full of the green coolant.
regards maxim

Dec 12, 2008 | 2005 Kymco Xciting 500

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kymco Experts


Level 3 Expert

85239 Answers

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

6517 Answers

Are you a Kymco Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides