Question about Kymco Motorcycles

1 Answer

How do I remove the cover of my tail light on my Kymco Quannon?

Posted by Alan J Cuthbertson on

Ad

1 Answer

L Pfaff

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Kymco Master
  • 11,573 Answers

Alan, You may have to remove rear fairing to access. Link to forum gives a good guide on how to remove tail light. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
http://www.kymcoforum.com/index.php?topic=3077.0
KYMCO AGILITY 125 Service Manual Page 181

Posted on Jun 26, 2016

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Kymco quannon 125cc wiring loom i need help with a very basic diagram showing only the wiring required to get motor running its in gokart the diagram i have dont understand please can anyone help me ?


Hello P Smurf,

Well... don't feel bad...!!
The KIMCO drawing is TRASH (in my humble opinion).

Just start the engine!
- ignition switch on (powers on CDI module)
- short B+ 12V to "S" lead (small terminal on solenoid switch = cranking motor (until it starts (or within reason... do not burn out starter)).

Really... you can short BATTERY to the starter solenoid... as long as you have the ignition on... It SHOULD RUN (if it can).

You only have the REAL two issues you need to start...
Fire & fuel... (everything else is mere confusion).

IGNORE IT ALL... until you get the engine started...!!

I've been reading schematics, circuit drawings, operational diagrams... All of it for more than my adult life... (mere seconds away from 70) amateur radio, patent holder & highly skilled professional... (into full spectrum optics)....

I pulled up the appropriate Kymco "drawing"... and while I'll say it is very pretty (colorful) it is also TOTALLY USELESS...!!
(top reference below... avoid it!).

Whom-so-ever (clown who posted it) that put it together
didn't (still doesn't) know their posterior from 75 cents
(six bits).
I can't even tell if the generator & starter are one-in-the-same
(which would be the first place you want to go...

Useable VERSION immediately below...


Quite Useless:
http://www.enmoto.com/enmotoonline/downloads/Specifications/Kymco/Schaltplaene/Quannon.pdf

I found another source... that has the COMPLETE information:
http://binatani.com/wp-content/uploads/2013/02/wiring-diagram-Kymco-Super8-125cc-engine.jpg http://binatani.com/wp-content/uploads/2013/02/wiring-diagram-Kymco-Super8-125cc-engine.jpg

If you don't have a spark tester just have a friend pull the HIGH-VOLTAGE wire loose enough to see the spark jump...

Else find the CDI Module/Coil... & replace it
(better to get a SPARK test tool...)...
I'm just saying

Comment me back... every tractor & tiller in the world has the same starter circuit
(some just have points & coils in lieu of CDI Modules).

I'll be here!!

Jun 05, 2016 | Kymco Motorcycles

1 Answer

Tail light cover removal? How do you remove the covers for the tail lights?


HI: To remove the Lens for your Rear Lights ,Just remove them from inside your Trunk: You'll Proball Beable to See The Hold Down Studs and Nuts Holding them In Place By Removing some of your Trunks Interior Linings In and Around Where your Tail Lights Are Mounted.Just Remove only the Interior Panels To Expose Your Access To Removing Your Tail Light Lens/Or Covers. Hope This Helps you Let Me Know By Voting For me. Thanks the WYOCWBOY

May 29, 2010 | 1985 Lincoln Town Car

1 Answer

2001 Ram 1500 Truck 2WD: how do you remove a tail light from a 2002 dodge r...


There are for Philip screws holding your tail light cover onto your dodge. Step 1: Just remove those screws and pull the cover off. Step 2: Remove the light bracket out of the cover and replace with a 1057 bulb.

May 18, 2010 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

Brake light, but no tail light


Buy the proper unit light switch ,if its faulty and can't be repaired ,bin it .

Mar 16, 2010 | 2005 Kymco Venox 250

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kymco Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

6517 Answers

Are you a Kymco Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...