Question about Goes Motorcycles

Open Question

I've got a k6 1000,the f1 code comes up and when that does the bike goes off a cylinder,when I turn the bike off it goes back to normal again, any help would be great thanks

Posted by [email protected] on

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The engine light comes on after start up then about 3 sec. goes off and the bike runs good and doesn't come back until start up, any ideas?


Normal computer diagnostics on ignition verify engine operations. Causes include loose wiring and electrical components. Battery and normal maintenance is a conclusion for some.

Jul 22, 2015 | 2007 Harley Davidson FLHTC Electra Glide...

1 Answer

Suzuki tl 1000r f1 light showing


F1 is no fault. put into dealer mode the little white connector under the rear seat, a bit of wire bridge the terminals and a fault code will come up, if you put a retarder on the bike try putting back to std

Dec 10, 2012 | 1999 Suzuki TL 1000 R

1 Answer

Bike back fires and the f1 light comes on on the cluster panel as well as bike dies


The F1 light is the FI fuel injection light. Your bike needs to be diagnosed and scanned by your dealer or trusted mechanic. There is a problem with your fuel system and a code has been registered, your bike won't start or run correctly until your mechanic has scanned, fixed and cleared the code.

Sep 11, 2011 | 2003 Honda VTX

1 Answer

Code reads random cylinder misfire. sporatically


well... the misfire codes are logged in when its running bad, but first I would want to verify fuel pressure when its running bad.

Oct 18, 2009 | 2006 Suzuki Forenza

1 Answer

1994 gw Interstate - turn key on - no lights neutral or oil press


It sounds like there may be an electrical leak, If the voltage goes too low, the computer either shuts down or it can go stupid where certain things won`t operate. Try turning everything off, disconnect the positive lead from the battery and connect an ammeter between the positive terminal of the battery and the positive connector that goes to the bike. There should be very little drain from the battery, (I presume it`s got a clock and maybe a radio with presets that require power). I would say if there is more than say 10 - 50mA showing on the meter, you`ve got a leak. I`ve just been explaining about one of these bikes where it was the rectifiers that were leaking. I`m only guessing so I hope this helps. Ian

Jul 15, 2009 | 1990 Honda GL 1500 SE Gold Wing

1 Answer

TOP DRAWER WAS NOT DRAINING..NOW THE F1 ON BOTH DRAWERS IS ON


F1 code indicates a leak,you will find the water under bottom drawer.Lid probably not sealing well.

Jun 17, 2009 | Fisher and Paykel 24 in. DD-602 Built-in...

1 Answer

Timer tone goes off with F1 display


Hi arl3933,

The "F1" error code description is a System Watchdog Circuit. Please press "CANCEL", if beeping continues after 30 seconds, please check the main control board(ERC). Here are basic test that will help you to determine if the ERC or touchpad is defective.

1. Unplug the range power cord or turn the power off to the range at the circuit breaker.

2. Gain access inside the control panel.

3. Disconnect the touch pad (also called keypad or membrane switch) ribbon from the ERC.

4. Make sure there are no lose wires, or anything else that may cause a short when power is turned back on. Assemble the control panel back the way it was.

5. Turn the power back on.

6. Wait for at least one hour to see if the code comes back.

7. If F1 comes back, replace the ERC. If it does not, replace the touch pad.

Hope it helps.

Thank you for using FixYa.

May 14, 2009 | Dacor Preference RSD30 Gas Kitchen Range

3 Answers

F1 light on and red light blinking, wont start


I was at the local race shop in Milton Fl getting new rear tire and the owner of the shop took it for a spin to scuff the tire. When he got back he said he got the F1 code. He plugged a short wire looking thing into a plug under the seat. Took it to code machine and got c-11 code. which is cam position sensor I think he said. but he said he had never seen that error code before. I think the F1 blinking light indicates an error only. You have to have it analyzed with the bike running and code blinking to diagnose the exact issue. Ive got the same bike pictured above and I have been getting error codes pretty much since I bought it brand new in 08. It doesnt seem to affect anything tho, the bike runs normally. Mine usually comes on everytime I start it when its cold. but I can let it run a few seconds then restart it and most of the time the light will not come back on for the rest of my ride. Every now and then it will come on while riding. So I dont know if I'm getting more codes than the C-11 that came up for dude at bike shop or not. I should have taken mine in to have it looked at but never did cuz the bike runs normal as far as i can tell. Annoying as hell though when it comes on at night.

Apr 13, 2009 | 2008 Suzuki GSX-R 600

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Goes Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Brad Brown

Level 3 Expert

18519 Answers

john h

Level 3 Expert

23504 Answers

Are you a Goes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...