Question about Zongshen Motorcycles
Hi Ben, you could have bad fuel, blocked or clogged float bowl vent line, fuel line, faulty petcock, or fuel tank or cap not venting properly. for more information about your question please visit the website below. Good luck and have a nice day.
Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e
Posted on Sep 28, 2015
2 stroke bike are very dependent on compression. and being a bike that is 12 years old my best educated guess is that the top end needs to be rebuilt. i usually have to have the top end done on my honda about every three years.
Posted on Jan 13, 2009
SOURCE: dead pw 50 and sad boy.
Many things could cause the problem. Let me see if I can help out.
You have spark, but is it enough spark? A weak battery can rob power from the coil so only a weak spark is present. Get a new stock NGK spark plug to eliminate the possibility of a problem plug.
It is good that you cleaned the carb because that would be my second target. Reset the air and idle screws. IMPORTANT > do not tighten these two screws down. Only screw these in until they LIGHTLY seat. Now turn each screw one and one half turns outward. Clean or replace the air filter and be sure the bolts are tight on the carb manifold. INSTALL AN IN-LINE FUEL FILTER. Let the float bowl fill then start the engine. Set the idle speed with the idle screw.
Remove the cylinder head. run the piston down to the bottom of the cylinder. look inside the cylinder. On th carb side (intake) you will see an intake port > a large hole that lets gas into the cylinder. Now look at the exhaust port. It is possible the exhaust port is pretty plugged up with carbon. The intake and exhaust ports should be approximately the same size. Are they? If not then remove the muffler and take a screw driver and plastic hammer and knock the carbon into the cylinder, thus enlarging the exhaust port to its' proper size and allowing the exhaust gases to escape. Vacuum the carbon out of the cylinder. De-carbon the piston top and the cylinder head.
Get back to me and tell me what you find. If more is needed we will go further.
Posted on Apr 12, 2009
just adjust the accelerator cable that is connecting to the fuel pump.check the and repair the throttle cause its the reason why it wont start . Its flooding the because of too much release of gas to the carb.
Posted on Jul 28, 2009
When I recently ordered parts from Saber Cycle, they included a piece of information that pertained to my motorcycle, which is also a 1983 Honda Goldwing GL1100 Interstate. Here is what it says, I hope this helps:
Air Cut-Off Valve
The air cut-off valve is an extremely important part of the fuel/air intake system that is frequently missed even my competent mechanics, most of whom are not even aware of its existence or how it functions.
Every GL1000 has one, located in the air intake tube, between the air cleaner box and the manifold. Every GL1100 has four, located in the top air intake passage of each carburetor, and every GL1200 has one located in the plenum box below the air cleaner box similar to the GL1000.
These valves are "air blockers", along with the carburetor o-rings, serving to restrict air flow and increase the fuel/air mixture ratio when the carb slides are in the lower RPM range, up to closed so that the machine will start and idle smoothly with virtually no choking and accelerate rapidly, with no stumble or hesitation.
When typical starting requires heavy and prolonged choking to keep the bike running, when stalling and hesitation occurs even while "warmed up" and when backfiring pops while the throttle is shut off while cruising, most people will start fooling with the air screws to try to overcome the problem, only making it worse along with reducing their gas mileage.
Running with dysfunctional air cut-off valves can causes severe engine damage or failure. When the valves are dysfunctional, the engine pulls nearly total air in the low RPM range through the carbs and on to the combustion chamber. The fuel/air ratio is extremely poor with pre-ignition long before the normal 38 to 40 degree firing point, generating an enormous amount of heat, with no power, which is trapped a longer period of time in the cylinder before the exhaust valve opens.
This heat goes mostly up through the cylinder head, gradually incinerating the head gaskets and allowing engine coolant (anti-freeze) to seep into the engine. You can easily spot when you are in trouble by a puff of bluish-white or white smoke on first starting the engine. Don't leave it alone. Change head gaskets immediately or you could take out your bottom end bearings, ruining the engine.
For those of you installing new exhaust systems, you will discolor your headpipes, either blue (lean state) or gold (rich state). You can destain your pipes using "blueaway" or "blue-off" but be careful not to rub the chrome, just dab gently.k These compounds are usually purchased at a Harley dealer or Harley oriented aftermarket shop.
Honda genuine pipes, like many Yamaha pipes, have a double wall for a portion of the headpipe which masks this discoloration-but also masks a bad state of tune. Even if your pipes are original and still in good shape, don't think that you are OK if the bike has any or all of the dysfunctional air cut-off valve running and performance characteristics.
If your 1975 to 1987 Gold Wing is not getting 50-58 miles per gallon (20-23 KM/Liter), you have one of the most obvious signs of trouble. It is likely your air screws have been backed out to try overcome the effects of the poor running, stumbling, starting and stalling and quitting.
Resynchronize all four carbs to the #3 carb vacuum level using mercury carb sticks or vacuum dial gauges. Stay with strict use of the setting levels in either the Honda, Clymer or Haynes manuals. Do not attempt to tune any other way! Guessing will not work and can cause considerable engine damage!!!
Posted on Sep 26, 2009
Check the valve adjustment. If a valve is standing open just a little, the compression will be too low to start the engine. Check fuel delivery by dribbling a little gasoline into the carb and try starting the bike. If it starts and runs for a second or two, you're not getting fuel into the cylinders. Check you carb again.
Posted on Oct 19, 2009
Tips for a great answer:
Aug 21, 2017 | GAS Motorcycles
Jun 18, 2017 | Zongshen Motorcycles
Apr 18, 2013 | Motorcycles
Dec 05, 2010 | 2003 Yamaha YZ 125
Jul 11, 2010 | 2002 Honda CR 250 R
Jun 09, 2010 | 2004 Yamaha TT-R 125 L
Dec 09, 2009 | 2003 kawasaki KX 125
Oct 18, 2009 | 2004 Suzuki DR-Z 125
Jul 11, 2009 | Craftsman 25cc Gas Line Trimmer
150 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: