Question about GAS Motorcycles

2 Answers

2009 Johnny Pag Spyder 300 cc. Why won't it start?

It won't start it I can hear it trying too but won't ... If I take the spark plugs out pour a little gas in then put the spark plugs back in eventually I can

Posted by Paul buckle on

Ad

2 Answers

terry stevens

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • GAS Master
  • 991 Answers

Check fuel filter and your float height could be set to low.

Posted on Jun 07, 2015

Ad

Giph Snelgrove

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

My Spyder stopped turning over altogether after sitting for about 2 weeks. Any tips?

Posted on Aug 11, 2020

Ad

5 Related Answers

Anonymous

  • 431 Answers

SOURCE: 1992 kawasaki Vulcan 750 stops running

Sounds like what you realy need to do is remove the carb jets and give them a good clean , this if I am right is the twin V 8 valve engine with twin Klhein carbs , make sure also your air filter is not dirty and check tank fuel filter ,, other than that you may be intrested in the manuel obtainable from this site
http://www.haynes.com/products/sfID1/8/sfID2/9/sfID3/81/productID/399
hope this helps good luck .. and Live long and prosper lol .. Regards Vortash

Posted on May 12, 2009

tabbycat282

tabbycat282

  • 56 Answers

SOURCE: 1989 tw200 yamaha won't start

G'day egdbcs . Ok.now lets see.You say good spark,so i'm presuming you are doing the old sight test.Try bending the arm on a know good sparkplug about 5-6mm,earth the plug and kick'er in the guts(crank it over)Be very carefull , high voltage danger.If there's still a good spark it's safe to say that there will also be a good spark under pressure in the combustion chamber,speaking of which you should also do a compression test,anything over 100psi should be ok. as i'm not to sure of the extent of the re-build,hopefully the valves were lapped and checked for straight and true and valve seals replaced,if you notice oil on the tip of the spark plug you could have a leaking valve seal or oil seal .Try putting a small amount of fuel directly into the combustion chamber ,tighten up the spark plug ,install the plug cap and.......Yeah ..You guessed it ..."kicker in the guts".If all the abouve are correct and true it should fire up.If it runs for 5-10 seconds then stops you've got some sort of fuel starvation problem , could be dirt in the carb,blocked idle jet ,or air passage or even the needle could have come off it's clip,believe me with an old bike like yours anything could be worn and loose inside that carby.The only other thing to consider is the timing.There may be a good spark but is it happening at the right time inside the engine???. I'll leave it all in your capable hands EGDBCS.Hope this helps to solving your worries. Chow for now......Tilleydog..

Posted on Jun 03, 2009

Anonymous

  • 867 Answers

SOURCE: Suzuki katana 600 not running

check your starter switch, it may be even grounding, which would cause all these problems

Posted on Jul 30, 2009

Anonymous

  • 116 Answers

SOURCE: wangye 50 cc scooter

sounds like gas jet is clogged. been sitting? use carb cleaner and clean out jet. the jet is in the carb bowl and has a stem amd needle valve and a float. when you see the float its attached with a small tab to the needle valve. up inside there is the jet a flat head screw driver to remove it. if its clogged clean it also on gas tank there may be a filter in the shut off valve. turn it off position and see if there is a screw underneath to clean filter.

Posted on Sep 22, 2009

Sindreme

  • 24 Answers

SOURCE: my son bought a Johny

If you forgot to refill motoroil the motor can be damaged. you can check in the clutch box to see if anything is stuck or broken. Good luck.

Posted on Jun 10, 2011

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does anybody know of any johnny pag servicers around wilkes barre pennsylvania?


cycle playground , DuPont pa if anybody from my area needs to know , found it myself , servicing only, not dealer

Sep 04, 2014 | 2007 Johnny Pag Spyder 300

1 Answer

Engine wont start


Here's a little trick that always works so long as your spark plug is in working condition. Remove the spark plug and pour a small amount of gas into the spark plug hole...I usually take the cap off of a tube of toothpaste and fill the cap with gas...it seems to be the right amount. After pouring it in, put the spark plug back in and start it up. If there is debris in the carburetor this will usually dislodge it through the vacuum of the running engine. Hope this helps : )

Jun 10, 2014 | Troy Bilt Tb70ss Gas Trimmer

1 Answer

Will not start, lights come on, signals work, etc.....


You hear some click from starter relay or any other sound when trying to start?
Have you checked the battery voltage?
This problem how happened? Next day or after a long time when motorcycle was unused?

Oct 20, 2013 | 2007 Johnny Pag Spyder 300

1 Answer

Electric start stop turning over, will not kick


Suddenly after you used the bike or after a long time when you didn't used it? The lights, horn, turn signals work?
Do you hear any click from the bike when you try to start it?

Oct 20, 2013 | 2007 Johnny Pag Spyder 300

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

588 people viewed this question

Ask a Question

Usually answered in minutes!

Top GAS Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Lawrence Oravetz

Level 3 Expert

10548 Answers

Brad Brown

Level 3 Expert

18519 Answers

Are you a GAS Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...