Question about 2010 Sym Mio 50

1 Answer

Headlight not working

BTY its a 2014 the bike is new less then 100 mi checked fuse not blown checked headlight not burnt out HELP.....

Posted by p segal on

Ad

1 Answer

RAYMONDO1953

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Prodigy:

    An expert who has answered 500 questions.

  • Sym Expert
  • 545 Answers

Firstly you need to see if you have a feed to the bulb itself

Posted on Mar 13, 2017

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 acura tsx headlight not working and need to put hi beam on


Fuse 28, a 10AMP fuse may be blown/bad. You may need a new one. Or your bulb may have burnt out. It's 12 years old. Any auto parts store guy could help you with it. (lower left side in this pic)
http://cimg0.ibsrv.net/cimg/www.acurazine.com/1024x768_85/240/fusediagram-164240.jpg

Video shows you how.
Blown Fuse Check 2004 2008 Acura TSX 2008 Acura TSX 2 4L 4 Cyl

Nov 16, 2016 | Acura Cars & Trucks

1 Answer

Headlights and etc. work but i get no power to ignition


Sounds like you have a burnt out switch, get a replacement from a breakers.

Aug 20, 2017 | Motorcycles

1 Answer

26av502r - blowing fuses. i disconnected the board from others and still blows fuses. bty, what rating is the fuse?


Hello,
You can do this by yourself all you have to do is to open the back cover of the television to check the faulty components. to fix you must have basic knowledge on electronics .

The fuses are there to protect the set from catching on fire in case there's a short circuit inside the set. Now in some cases an intermittent short can work after you replace the fuse but if its burnt black or brownish, there's a circuit inside the set in one of the circuits. always use a 100 watt light bulb across a blown fuse if your not sure if there is a short. if there is, the light will absorb the short and glow bright. if there is no short the bulb will glow bright , then go down very dim. you could have a main power supply problem, such as shorted bridge rectifiers,shorted main b+ capacitor, Hot could be shorted, or the Vertical or audio output IC could be shorted.

I hope this help in solving the problem.....

Nov 10, 2010 | Toshiba 26 26AV502R 26 in. LCD HDTV

2 Answers

My pit bike 125cc wont fire up


Try unpluging the cutouts.they are usally on 2-3 places on these bikes ,brakes,also check the fuse that is on the red wire comming off the battery it will be blown or end of fuse holder will be pushed in and not touching the fuse.

Apr 13, 2010 | RTO Pit Bikes

1 Answer

Took my bike out, WR450f 07 model, got to the shop and had something to eat, came out and bike wouldn't go, headlight globe was blown, actually smashed, was no spark so replaced spark plug and checked...


My thoughts...Light globes are made to withstand voltages of less than 16 volts. So if you are finding your headlight globe burnt out, it's because the system voltage has exceeded this. Have your voltage regulator replaced which will remedy the problem. Over voltage will have an effect on other electronic components such as the CDI unit and wreck your battery too.

Apr 07, 2010 | Yamaha WR 450 F Motorcycles

1 Answer

NO LOW BEAM, EVERYTHING CHECKS OK . I HAVE CHECKED ALL BULBS AND FUSES


Hi,
The simple answer may be that the low beam side is burnt out. Replace the bulb.
However, if both headlights have stopped working when switching to low beams, there may be a problem with the relay or the switch itself. If the cost of a relay is low for your car, it may be less expensive to simply replace that component than to have it diagnosed in a repair shop. Replacement of the switch requires some disassembly of the steering column or dash in most vehicles.
This is how to fix the low beam..
1.Check your fuses. The plastic panel covering the fuses should have a diagram detailing what each fuse covers. If yours is missing, or unlabeled, check your owner's manual, or a Hanes(tm) or Chilton(tm) repair manual. Often if a headlight is not working, it is the result of a blown fuse. Fuses have a wire running through them that will melt when too much current is run through them. If the fuse is blown, the wire will be broken. If the fuse for the headlight you are working on has an intact wire, it is likely the problem lies elsewhere.
2.Swap the headlight for its twin. If your left headlight does not work, put the light from your right headlight in its place. If it works with the other headlight in place, your headlight bulb is dead, and needs to be replaced.
3.If this does not work, try using a voltmeter on the plug for the bad headlight. Turn on the ignition, and turn the headlight switch. If the voltmeter shows no current, then either your switch or the wiring leading to the headlight has gone bad.
4.If replacing your headlight switch does not solve the problem, then there is a break in the wiring leading to the headlight, and the wiring will need to be replaced.
Thanks for contacting fixya.com

Nov 11, 2009 | 2002 GMC Yukon Denali

Not finding what you are looking for?
2010 Sym Mio 50 Logo

Related Topics:

77 views

Ask a Question

Usually answered in minutes!

Top Sym Experts

Arnie Burke
Arnie Burke

Level 3 Expert

6647 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

Brad Brown

Level 3 Expert

18665 Answers

Are you a Sym Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...