Question about 2005 KTM 250 SX

1 Answer

Ktm 250 sx

How much fork oil is used in front forks

Posted by Anonymous on

Ad

1 Answer

Gary

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 127 Answers

The SX forks really should be taken to a suspension tech to get the inner chamber properly bleed out.
You never just add a cc amount because there is usually some left inside. You bleed out the air and fill. once no more air is coming out you set the fluid level on the outter chamber 110mm to 120mm with the spring out and the fork collapsed.

Posted on Jan 07, 2015

Ad

2 Related Answers

tabbycat282

tabbycat282

  • 56 Answers

SOURCE: How much fork oil in a 2002 KTM 400 SX

White power allow a 110mm air gap with springs out and fork compressed as a general guide ,adjust from there according to prefrance . Thats probably,from memory about 600ml or so.If you overfill the leg ,cut the tip off the fork oil bottle , mark out on a clear piece of fuel hose 110 mm from one end of hose with a permanent marker, attach other end to the tip of the now empty fork oil bottle nipple, squeeze bottle,insert hose down to 110mm mark,take hand pressure off bottle and WWHHAAALLLAAA!!!!!!!!. Magically the excess oil is sucked back up into bottle.....Don't you just love the forces of nature. : ] ride on DB ......Hope this gets you out of trouble ....Flabbycat

Posted on Apr 17, 2009

Ad

SOURCE: How much oil do you put in the front forks of a 2004 ktm sx 250

A good rule of thumb on anything that has a plug that removes to pour oil in, which I am assuming this one does, get it level and pour oil into it until it just starts to run out of the hole,. Again make sure it is setting level.
Gillight

Posted on Jun 22, 2012

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace fork seals 2007 fatboy


To replace the front fork oil first support the motorcycle so the front end is off the floor and the forks are fully extended. Remember that the FLSTC and FLSTF models have a preloaded fork spring and that the fork tube plug is under spring pressure.Then you remove the fork tube caps. And then you drain the fork oil. ON FXSTD models, your remove the drain screws and washers from each fork and drain the fork oil this way. ON ALL MODELS EXCEPT the FXSTD, remove and discard the drain screws and washers from each fork and drain the fork oil and then you install new drain screws and washers. ON FXSTD models, apply LOCTITE THREADLOCKER 243 (blue) to the drain screws and tighten them to 12-18 inlbs (1.4-2.0 Nm). ON ALL MODELS EXCEPT FXSTD, tighten the drain screws to 52-78 in-lbs (5.9-8.9 Nm).THEN fill the fork with Harley-Davidson TYPE E FORK OIL (Part No. HD-99884-80).Either by installing oz or cc's of fluid if the forks were left in the frame or by measuring the amount of oil in the tubes in inches or mm if the forks were removed from the frame and disassembled. In the latter case the oil level is measured from the top of the fork tube with the spring removed and the fork fully compressed.

MODELs FLSTC, FLSTN use 13.4 OZ 395 cc4.41 inches 112.0 mm
MODEL FLSTF uses 13.4 OZ 397 cc5.04 inches128.0 mm
MODELs FXST, FXSTB, FXSTC use 12.5 OZ370 cc 6.69 inches170.0 mm
MODEL FXSTD uses 11.6 OZ343 cc 7.48 inches190.0 mm

FINALLY tighten the fork tube caps to 40-60 ft-lbs (54.2-81.3 Nm).

Jul 10, 2014 | 1993 Harley Davidson FLSTF Fat boy

1 Answer

How much oil in front forks?


The fork oil should come to just below the bottom of the threads of the bolt by the o ring. do not use regular motor oil as it doesn't have the correct viscosity that fork oil has. Make sure both forks have the same amount of oil to prevent an unbalanced feel to the front end

May 30, 2014 | 2003 Suzuki VL 1500 Intruder LC

1 Answer

2003 HD sportster - forks don't leak, bottoms out when front brakes applied


You may not have enough oil in the front forks or you may been a heavier viscosity of oil. I'm sorry but I don't have the oil capacity for your "Low Sportster". All I have is for "Hugger" models. They take 10.7oz. "wet" and 12.1 "dry". The difference between "wet" and "dry" is that if you simply drain and refill the front forks, it's call a "wet" oil change. If you disassemble and clean the forks of all oil inside, it's called a "dry" oil change. Contact the service department of your local shop and ask them how much oil goes in the front fork. To change the oil, there is usually a small screw in the trailing side of the lower fork slider down near the axle. Take these out and the oil will drain to a certain degree. Hold the brake while working the forks up and down with your weight to get all the oil that draining will get out of them. If you want all the oil out, you'll have to disassemble the fork tube. I would not do this if the seals are not leaking. Replace the screws in the sliders and then remove the top cap from one tube at the time and refill the tube with the specified amount of oil. Sometimes, the top caps can be difficult to get back in due to the pressure of the large spring in the front fork tubes. You may need a tool to compress the sping. I'm not sure on the "Low" model. I've always managed to the top caps back in without any special tool but I've never done a "Low" model bike. Harley uses what they call their "Type E" fork oil. I do not know what the viscosity of this oil is so I always use PJ-1 30 weight fork oil for most applications. Use only fork oil as any other oil may have a tendency to foam thereby negating any dampening action of the forks. If this doesn't solve your problem, you may want to check into changing the springs in the front forks. Progressive Suspension and others make kits for this.

Good Luck
Steve

Sep 13, 2011 | 2006 Harley Davidson XL 1200 L Sporster...

1 Answer

How much fork oil is required in the front forks of a 2000 suzuki 800 intruder and how do you measure if you put too much in. The guy at cycle gear where I bought the fork oil said to top it off or fill...


Hi, all model VS 800 from1992-2000 take the same amount of oil in the front forks, using 10 weight fork oil measure into a clean measuring device or mark the side of the oil bottle 413 mls, pour this caerfully into 1 fork, and the same amount into the other fork, 413/413 cm (3)

May 09, 2011 | 2000 Suzuki VS 800 Intruder

1 Answer

How do i change fork oil an will it make them stiffer an is they a number where i can talk to ya


To change the fork oil, look down on the lower part of each fork leg just above the axle on the backside of each leg and you'll find an Allen plug or small screw. Take this screw out, hold the front brake and push down on the front forks. The fork oil will come out of the tube. Do both sides at the same time. Once you get the oil out of them, reinstall the drain plug. Then, take the large hex cap on ONE TUBE AT THE TIME and pour the correct amount of the correct fork oil into each tube. There is a specific amount of oil that must be poured into each leg. Since you simply drained your forks instead of disassembling them, you should use what is known as the "Wet" quantity of oil. I'm pretty sure your bike takes 9.0 ounces of oil in each leg. Call your local dealer and they'll tell you how much oil to put in. Your bike came from the factory with "Type E" oil in the forks. The viscosity of the oil determines the dampening effect of the forks. Heavier oil will stiffen the front forks, a lighter viscosity of oil will make the front end softer. You can check the Internet for fork oils and they should give you a comparison of what weight oil is equivalent to "Type E" oil. I think PJ 1's 30 weight oil is the same as type E Harley oil. Use only "fork oil" in your front forks as it has special "anti-foaming" agents in it. If the oil foams up, you'll lose the dampening effect in your forks.

Good Luck
steve

Apr 20, 2011 | 2004 Harley Davidson XL 1200 C Sportster...

1 Answer

How much fork oil goes in the forks of an 2001 FXD and how do I do this ? Do you have any diagrams to help me with ?




I have no diagrams for you. MAke your own as you take it apart etc and take lots of cell phone pictures if you need help remembering how to put things back together.

Table 1-6. Type E Fork Oil Amounts



MODEL OZ CC IN. MM



FXDXT 11.5 341 6.10 154.9



FXDWG 12.0 356 7.28 184.9



FXDL 10.7 316 7.20 182.9



FXD 10.6 314 6.69 169.9




Changing fork oil is a simple mater for some models and requires fork disassembly for others. Here is the procedure for all 2001 DYNA models:

2001 DYNA FRONT FORK OIL 1.18


REPLACING FORK OIL Replace front fork oil at every 20,000 mile (32,000 km) service interval and/or prior to storage.


ALL BUT FXDX & FXDXT models


Raise and support the motorcycle so the front end is off the floor and the forks are fully extended, on FXDL models, remove the center plug from each fork cap, on all other models, remove the fork tube caps, remove the drain screws from the bottom of each fork and drain the fork oil, replace the drain screws and washers and tighten the screws

to 13-17 in-lbs (1.5-2.0 Nm) THEN see Table 1-6. and fill the fork with Harley-Davidson TYPE E FORK OIL (Part No. HD-99884-80) as set out in the Table. THEN if apart assemble the forks as follows:


a. FXD, FXDXT, FXDWG models: install both fork tube caps and tighten them to 11-22 ft-lbs (14.9-29.8 Nm).

b. FXDL models: install center plugs and tighten until secure.


Fork oil amounts can be measured two ways: use the oz./cc measurement if fork is left in frame; use the in./mm measurement if the fork is disassembled in which case the oil level is measured from the top of the fork tube with the spring removed and the fork fully compressed.


Table 1-6. Type E Fork Oil Amounts for 2001 DYNA


MODEL OZ CC IN. MM

FXDXT 11.5 341 6.10 154.9

FXDWG 12.0 356 7.28 182.9

FXD 10.6 314 6.69 169.9


PART NO. SPECIALTY TOOL

HD-41177 Fork tube holder

HD-41549A Fork spring compression tool

HD-41551 Spring plate tool

HD-36583 Fork seal installer

HD-59000A Pro-level oil gauge



FRONT FORKS: FXDX & FXDXT 2.20

REMOVAL

Raise and support the motorcycle so the front end is off the floor and the forks are fully extended, remove both front brake calipers and the front wheel, remove the front fender, remove the front fairing, remove the headlamp bracket and attach the headlamp to the frame using a rubber bungee strap, loosen the upper and lower triple clamp pinch bolts and pull the fork sides from the brackets.


DISASSEMBLY

Remove the stopper ring, remove the spring preload adjuster but DO NOT unthread the rebound adjuster from the damper rod because incorrect assembly could result in reduced adjustment range. THEN unthread the fork cap from the fork tube and allow the fork leg to drop, exposing the spring, THEN get a FORK SPRING COMPRESSION TOOL (Part No. HD-41549A) on the spring collar, turn the screws in to engage the holes in collar, compress the spring until the SPRING PLATE TOOL (Part No. HD-

41551) can be positioned between the spacer and the spring collar, THEN hold the fork bolt and compression adjuster, remove the fork bolt from the compression adjuster, remove the spring adjuster plate from the fork bolt, remove spacer, spring collar and spring, pour out the fork oil by pumping the fork leg and rod 8-10 times or until rod the moves freely. THEN position fork slider in vise using a FORK TUBE HOLDER such as (Part No. HD-41177) to avoid damage. THEN remove the socket head bolt, remove the damper from the fork tube, remove the cover from the slider, remove seal and stopper ring, pull the fork tube out of the slider, remove the oil seal, spacer and guide bushing from the fork tube.


CLEANING AND INSPECTION

Measure the fork spring free length and replace the spring if it is shorter than 17.00 in. (431.8 mm), check the fork tube and the slider for score marks, scratches or abnormal wear, check the slide and guide bushings for excessive wear or scratches, set the fork tube on V-blocks and measure runout which should not exceed 0.008 in. (0.2 mm).


ASSEMBLY

Coat the oil seal with TYPE E FORK OIL, before installing the slide bushing and guide bushing, lubricate them with fork oil, THEN install the guide bushing and the spacer seal noting that the guide bushing opening must be oriented to the side and NOT to the front or rear, THEN slip the slider into the fork tube, place the slide bushing over the fork tube until it rests on the slider, drive the guide bushing with the spacer seal into the slider, lubricate a new oil seal with TYPE E FORK Oil, drive the oil seal into the slider using FORK SEAL INSTALLER (Part No. HD-36583). install the stopper ring and dust seal, (if the rebound adjuster was removed from the damper rod bottom the lock nut on the threaded portion of damper rod, holding a thumb on the detent spring and ball, back out (turn counterclockwise) the rebound adjuster to the last "click." and then turn down (clockwise) 17 "clicks", thread the rebound adjuster onto the damper rod until the adjuster stops at maximum thread engagement (but do not force it), thread the locknut onto the damper rod up until it contacts the base of the rebound adjuster and tighten it in place), THEN holding the slider in a vise while being careful not to damage it. install the damper tube into the fork tube and tighten the socket screw and washer to 22-29 ft-lbs (29.8-39.3 Nm). THEN pour half the TYPE E FORK OIL into the fork tube, slowly pump the damper rod 10 or more times, position the damper rod in the fully bottomed position and pour the remaining amount of TYPE E FORK OIL into the fork tube. THEN using a PRO-LEVEL OIL GAUGE (Part No. HD-59000A) or similar adjust the oil level to 5.04 in. (128 mm). THEN carefully clean and install the spring, the spring collar, and the spacers with the sharp edge created when they were stamped out when manufactured, facing the collar. THEN using a FORK SPRING COMPRESSION TOOL such as (Part No. HD-41549A) push spring collar down and place a SPRING PLATE such as (Part No. HD-41551) between the spacer and the spring collar, install the fork cap and tighten it against the rebound adjuster to 22-29 ft-lbs (29.8-39.3 Nm). THEN tighten the fork cap onto the fork tube to 11-22 ft-lbs (14.9-29.8 Nm), install the spring adjuster plate, replace the O-rings on the spring preload adjuster and lubricate them with fork oil. THEN install the spring preload adjuster and the stopper ring and carefully drive the slider cover into the slider.


INSTALLATION

Insert both fork side assemblies up through the fork stem and bracket and upper bracket and tighten the fork stem bracket pinch bolt(s) to 30-35 ft-lbs (40.7-47.5 Nm). Then re-install the headlamp bracket, install the front fender, install the front wheel and the brake caliper When the motorcycle is again ready for the road adjust the headlamp and road test the motorcycle.






Feb 10, 2011 | Harley Davidson FXD Dyna Super Glide...

1 Answer

How do you remove the forks on a 2001 fxd superglide






Hopefully you will glean all you need to know from this but if you want or need more information or more FXD specific information PLEASE H

Hopefully the information below will be okay BUT if you need any more or any more specific information please post a comment and describe what you want/need.

REPLACING FORK OIL Replace front fork oil at every 20,000 mile (32,000 km) service interval and/or prior to storage.


ALL BUT FXDX & FXDXT models


Raise and support the motorcycle so the front end is off the floor and the forks are fully extended, on FXDL models, remove the center plug from each fork cap, on all other models, remove the fork tube caps, remove the drain screws from the bottom of each fork and drain the fork oil, replace the drain screws and washers and tighten the screws

to 13-17 in-lbs (1.5-2.0 Nm) THEN see Table 1-6. and fill the fork with Harley-Davidson TYPE E FORK OIL (Part No. HD-99884-80) as set out in the Table. THEN if apart assemble the forks as follows:


a. FXD, FXDXT, FXDWG models: install both fork tube caps and tighten them to 11-22 ft-lbs (14.9-29.8 Nm).

b. FXDL models: install center plugs and tighten until secure.


Fork oil amounts can be measured two ways: use the oz./cc measurement if fork is left in frame; use the in./mm measurement if the fork is disassembled in which case the oil level is measured from the top of the fork tube with the spring removed and the fork fully compressed.


Table 1-6. Type E Fork Oil Amounts for 2001 DYNA


MODEL OZ CC IN. MM

FXDXT 11.5 341 6.10 154.9

FXDWG 12.0 356 7.28 182.9

FXD 10.6 314 6.69 169.9


PART NO. SPECIALTY TOOL

HD-41177 Fork tube holder

HD-41549A Fork spring compression tool

HD-41551 Spring plate tool

HD-36583 Fork seal installer

HD-59000A Pro-level oil gauge



FRONT FORKS: FXDX & FXDXT 2.20

REMOVAL

Raise and support the motorcycle so the front end is off the floor and the forks are fully extended, remove both front brake calipers and the front wheel, remove the front fender, remove the front fairing, remove the headlamp bracket and attach the headlamp to the frame using a rubber bungee strap, loosen the upper and lower triple clamp pinch bolts and pull the fork sides from the brackets.


DISASSEMBLY

Remove the stopper ring, remove the spring preload adjuster but DO NOT unthread the rebound adjuster from the damper rod because incorrect assembly could result in reduced adjustment range. THEN unthread the fork cap from the fork tube and allow the fork leg to drop, exposing the spring, THEN get a FORK SPRING COMPRESSION TOOL (Part No. HD-41549A) on the spring collar, turn the screws in to engage the holes in collar, compress the spring until the SPRING PLATE TOOL (Part No. HD-

41551) can be positioned between the spacer and the spring collar, THEN hold the fork bolt and compression adjuster, remove the fork bolt from the compression adjuster, remove the spring adjuster plate from the fork bolt, remove spacer, spring collar and spring, pour out the fork oil by pumping the fork leg and rod 8-10 times or until rod the moves freely. THEN position fork slider in vise using a FORK TUBE HOLDER such as (Part No. HD-41177) to avoid damage. THEN remove the socket head bolt, remove the damper from the fork tube, remove the cover from the slider, remove seal and stopper ring, pull the fork tube out of the slider, remove the oil seal, spacer and guide bushing from the fork tube.


CLEANING AND INSPECTION

Measure the fork spring free length and replace the spring if it is shorter than 17.00 in. (431.8 mm), check the fork tube and the slider for score marks, scratches or abnormal wear, check the slide and guide bushings for excessive wear or scratches, set the fork tube on V-blocks and measure runout which should not exceed 0.008 in. (0.2 mm).


ASSEMBLY

Coat the oil seal with TYPE E FORK OIL, before installing the slide bushing and guide bushing, lubricate them with fork oil, THEN install the guide bushing and the spacer seal noting that the guide bushing opening must be oriented to the side and NOT to the front or rear, THEN slip the slider into the fork tube, place the slide bushing over the fork tube until it rests on the slider, drive the guide bushing with the spacer seal into the slider, lubricate a new oil seal with TYPE E FORK Oil, drive the oil seal into the slider using FORK SEAL INSTALLER (Part No. HD-36583). install the stopper ring and dust seal, (if the rebound adjuster was removed from the damper rod bottom the lock nut on the threaded portion of damper rod, holding a thumb on the detent spring and ball, back out (turn counterclockwise) the rebound adjuster to the last "click." and then turn down (clockwise) 17 "clicks", thread the rebound adjuster onto the damper rod until the adjuster stops at maximum thread engagement (but do not force it), thread the locknut onto the damper rod up until it contacts the base of the rebound adjuster and tighten it in place), THEN holding the slider in a vise while being careful not to damage it. install the damper tube into the fork tube and tighten the socket screw and washer to 22-29 ft-lbs (29.8-39.3 Nm). THEN pour half the TYPE E FORK OIL into the fork tube, slowly pump the damper rod 10 or more times, position the damper rod in the fully bottomed position and pour the remaining amount of TYPE E FORK OIL into the fork tube. THEN using a PRO-LEVEL OIL GAUGE (Part No. HD-59000A) or similar adjust the oil level to 5.04 in. (128 mm). THEN carefully clean and install the spring, the spring collar, and the spacers with the sharp edge created when they were stamped out when manufactured, facing the collar. THEN using a FORK SPRING COMPRESSION TOOL such as (Part No. HD-41549A) push spring collar down and place a SPRING PLATE such as (Part No. HD-41551) between the spacer and the spring collar, install the fork cap and tighten it against the rebound adjuster to 22-29 ft-lbs (29.8-39.3 Nm). THEN tighten the fork cap onto the fork tube to 11-22 ft-lbs (14.9-29.8 Nm), install the spring adjuster plate, replace the O-rings on the spring preload adjuster and lubricate them with fork oil. THEN install the spring preload adjuster and the stopper ring and carefully drive the slider cover into the slider.


INSTALLATION

Insert both fork side assemblies up through the fork stem and bracket and upper bracket and tighten the fork stem bracket pinch bolt(s) to 30-35 ft-lbs (40.7-47.5 Nm). Then re-install the headlamp bracket, install the front fender, install the front wheel and the brake caliper When the motorcycle is again ready for the road adjust the headlamp and road test the motorcycle.

Oct 01, 2010 | 2001 Harley Davidson FXD Dyna Super Glide

2 Answers

Yamaha xj 900 s Front fork oil amount in cm


The forks hold 286ml or 9.67 US OZ of oil, best would be to use hydraulic oil.
Good Luck.

Jan 27, 2010 | 2000 Yamaha XJ 900 S Diversion

3 Answers

I need to know the oil capacity of the front forks on my 1999 Suzuki Marauder VZ800.


FORK OIL
• Place the front fork vertically without spring.
• Compress it fully.
• Pour specified front fork oil up to the top level of the outer
tube.
Capacity (each leg): 490 ml (16.6/17.3 US/lmp oz)
99000-99044-L01: SUZUKI FORK OIL L01
or an equivalent fork oil
• Move the inner rod slowly with the special tool ten times and
more until no more bubbles come out from the oil.
09940-52841: Inner rod holder
NOTE:
Refill front fork oil up to the top of the outer tube so that bubbles
are visible while bleeding air.
• Refill specified front fork oil up to the top level of the outer
tube again. Move the outer tube up and down several strokes
until no more bubbles come out from the oil.
• Keep the front fork vertically and wait 5 – 6 minutes.
NOTE:
* Always keep oil level over the cartridge top end, or air may
enter the cartridge during this procedure.
* Take extreme care so as to pump out air completely.
• Hold the front fork vertically and adjust fork oil level with the
special tool.
NOTE:
When adjusting the fork oil level, compress the outer tube fully
without the fork spring.
Fork oil level: 153 mm (6.02 in)
09943-74111: Front fork oil level gauge

Dec 18, 2009 | 1998 Suzuki VZ 800 Marauder

3 Answers

Fork oil capacity


Front Fork Oil cc (right leg) : 485 Front Fork Oil cc (left leg) : 495

Nov 10, 2008 | 1999 Honda CBR 1000 F

Not finding what you are looking for?
2005 KTM 250 SX Logo

240 people viewed this question

Ask a Question

Usually answered in minutes!

Top KTM Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

217 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

6517 Answers

Are you a KTM Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...