Question about 1979 Yamaha XS 650 F

Open Question

Yamaha xt 600 tenare model number - 1979 Yamaha XS 650 F

Posted by Anonymous on

Ad

5 Related Answers

Anonymous

  • 298 Answers

SOURCE: Looking for an online owners manual for an XT 600

Hi there!

Can't find an owners manual but i found a parts catalog!

http://www.carlsalter.com/aaman/Yamaha%20xt600e%20%20parts%20catalogue.pdf

Hope this helps! I'd appreciate a feedback!
-levibit-

Posted on Mar 19, 2009

Ad

Fabrice Wolters

  • 331 Answers

SOURCE: no spark

remove the ignition coil from the bike.

The primary winding should have a resistance between 2 and 6 ohms
The secondary winding should have a resistance between 19Kohm and 40Kohm.

In fact the primary must have less than a 50ohm, but there MUST be a resistance.
The secondary should have a resistance of 15.000Ohms and more, but there MUST be a continuity.

Posted on Apr 02, 2009

Ad

tombones

  • 3567 Answers

SOURCE: i can not find maintenance manual for YAMAHA XT 600 E

Google " service manuals yamaha "
or go to www.repairmanuals.com
or try your local library. Often guys will donate manuals to the library.

You can get a free pdf service manual on this site;
http://www.carlsalter.com/motorcycle-manuals.asp

Please rate this solution.
( four diamonds would be nice ), Thanks wdns331m!

Posted on Apr 06, 2009

Anonymous

  • 490 Answers

SOURCE: Yamaha XT 600 replace rubber boots on forks

you have to loosen the triple clamps and slide the forks completely off of the bike then loosen the clamps on the boots and slide them off

Posted on Apr 12, 2009

tombones

  • 3567 Answers

SOURCE: I want to remove the magneto from a Yamaha xt350

Back the screw handle out so the end of the screw is inside the the large collar. Remove the nut and washer holding the flywheel on the crankshaft. Screw the puller collar fully into the flywheel. Now turn the screw handle inward to contact the end of the crankshaft. Tighten the handle down then strike the handle arm with a hammer for extra pressure on the screw. Next, strike the center of the screw with the hammer. Alternate strikes between the center screw and the screw handle. Do that until the flywheel pops free. Some pullers have flats for wrenches instead of a screw arm. The principle for removal is the same.

Posted on Apr 13, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will a 1989 xt 600 front wheel fit on a 1990 yamaha xt 600?????


The front hubs have the same part number, but the rims are a little different the 1989 is 1.6 inches wide and the 1990 is 1.85 wide. The only problem may be a clearance issue with the width of the rim, other than that it will fit.

Nov 15, 2010 | 1990 Yamaha XT 600 E

2 Answers

Need a WIRING XT550J.PDF SCHEMATIC Circuit


Hi
Have a XT 400 1982 year model. Had problems with ignition as well as carburator on this. Used a wiring diagram from a XT 600 (are more or less the same on these models (400, 550 and 600) Bike is running like never before now. Have the complete manual (for the XT 600)that can be mailed over.
Peter

Sep 03, 2009 | 1990 Yamaha XT 600 E

2 Answers

I can not find maintenance manual for YAMAHA XT 600 E


Google " service manuals yamaha "
or go to www.repairmanuals.com
or try your local library. Often guys will donate manuals to the library.

You can get a free pdf service manual on this site;
http://www.carlsalter.com/motorcycle-manuals.asp

Please rate this solution.
( four diamonds would be nice ), Thanks wdns331m!

Apr 06, 2009 | 1990 Yamaha XT 600 E

Not finding what you are looking for?
1979 Yamaha XS 650 F Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

gbob59

Level 3 Expert

3063 Answers

randymanfive

Level 3 Expert

501 Answers

Cindy Wells

Level 3 Expert

6199 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...