What does fault code 838 camshaft position sensor g1 63 sporadic 006 short to pluse mean?

P1336 Ford P1336 Ford - Crankshaft Position Or Camshaft Position Sensor Input Signal Error Share
0 ' Add Comment Possible causes
- Faulty Crankshaft Position Sensor
- Faulty Camshaft Position Sensor
- Crankshaft Position Sensor harness is open or shorted
- Crankshaft Position Sensor circuit poor electrical connection
- Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
What does this mean? When is the code detected?
The Engine Control Module (ECM) has detected a synchronization or signal error from the cam or crank sensors
Possible symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Lack/Loss of Power
- Engine Stall
- Engine difficult to start
P1336 Ford Description
The input signal to the powertrain control module (PCM) from the crankshaft position (CKP) sensor or the camshaft position (CMP) sensor is erratic.

Read more: http://www.engine-codes.com/p1336_ford.html#ixzz3qT9Hiztc

Definition of Diagnostic Trouble Code P1345 Audi: Ignition Coil Power Output Stage 3 Short to Ground BMW: Misfire Cylinder 2 with Fuel Cut-Off Buick: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Cadillac: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Chevrolet: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Ford: Cylinder Discrimination Signal (Signal From Camshaft Position Sensor) GMC: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Isuzu: Crankshaft Position - Camshaft Position Correlation Kia: No SGC Signal (1.6L) Lexus: Variable Valve Timing / CMP Sensor Range / Performance Lincoln: Cylinder Discrimination Signal (Signal From Camshaft Position Sensor) Mazda: Cylinder Discrimination Signal (from CMP sensor) Mercury: Cylinder Discrimination Signal (Signal From Camshaft Position Sensor) Oldsmobile: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Pontiac: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Saturn: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Toyota: Variable Valve Timing / CMP Sensor Range / Performance Volkswagen: Ignition Coil Power Output Stage 3 Short to Ground

Camshaft position sensor B bank 2 CKT range / performance.
Faulty Camshaft Position Sensor
Camshaft Position Sensor harness is open or shorted
Camshaft Position Sensor circuit poor electrical connection
Faulty starter motor
Starting system circuit
Dead (Weak) battery
Any of these could cause this fault code.

P0344 Dodge - Camshaft Position Sensor Intermittent Interruption Bank 1 Sensor 1

Possible causes
- Faulty Camshaft Position Sensor
- Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
- Faulty starter motor
- Starting system circuit
- Dead (Weak) battery

It is the camshaft position sensor A bank 1 code.
Here are possible causes:
- Faulty Camshaft Position Sensor
- Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
- Faulty starter motor
- Starting system circuit
- Dead (Weak) battery

what is the question?, above are all statements.

if unsure ?, read the FSM on your and your engine options.

EOBD II Error Code: P0117
Fault Location:
Engine Coolant Temperature (ECT) Sensor (G62) - Low Input
Possible Cause:
Malfunction Indicator Lamp (MIL) Triggered on first occurrence.
Coolant thermostat.
Wiring short to earth.
Engine coolant temperature (ECT) sensor.

EOBD II Error Code: P0340
Fault Location:
Camshaft Position (CMP) Sensor A (G40), Bank 1 - Circuit Malfunction
Possible Cause:
Malfunction Indicator Lamp (MIL) active.
Wiring from/to Camshaft Position Sensor (CMP) faulty.
Camshaft position (CMP) sensor faulty.
Timing misaligned.
Possible Solutions:
Check Wiring from/to Camshaft Position Sensor.
Check Camshaft Position Sensor.
Check Timing.

EOBD II Error Code: P0500
Fault Location:
Vehicle Speed Sensor (VSS) - Circuit Malfunction
Possible Cause:
Malfunction Indicator Lamp (MIL) Non Emission Fault - No warning light.
Wiring.
Vehicle speed sensor (VSS).
Engine control module (ECM).

P1684 The battery has been disconnected within the last 50 starts.

P0340


This indicates that a problem was detected in the camshaft position sensor circuit. Since it says circuit, that means the problem could lie in any part of the circuit - the sensor itself, the wiring, or the PCM. Don't just replace the CPS (camshaft position sensor) and think that will definitely fix it.
Symptoms Symptoms can include:

• Hard starting or no start
• Rough running / misfiring
• Loss of engine power

Causes A code P0340 could mean one or more of the following has happened:

• a wire or connector in the circuit could be grounded/shorted/broken
• the camshaft position sensor may have failed
• the PCM may have failed
• there exists an open circuit
• the crankshaft position sensor may have failed

Possible Solutions With a P0340 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:

• Visually inspect all the wiring and connectors in the circuit
• Check for continuity in the circuit wiring
• Check the operation (voltage) of the camshaft position sensor
• Replace the camshaft position sensor as required
• Check the crankshaft position circuit as well
• Replace circuit wiring and/or connectors as required
• Diagnose/replace the PCM as required

For most people with 1992 Honda Civics this code can be resolved by checking the connections on the Cylinder position/camshaft position sensor which is located near the distributor. Make sure it is not shorting out and clean the area. If that doesn't work then the distributor needs to be replaced. Thanks for using Fixya.

Code P0340 is a camshaft position sensor CIRCUIT fault. This means it can be a bad sensor, wiring fault (loose connector, short, open), or even a bad PCM. Since you've already changed the camshaft position sensor you've eliminated that possibility. It's time to do some electrical troubleshooting. That, of course, depends upon your skill set for this type of work and equipment (mostly a good dmm and schematics). If you're not equipped for this then you'll likely have to seek assistance from a local shop.

If this reply answers your question then please take a moment to rate this post. - Thanks.