Question about 2006 BMW R 1200 GS Adventure

1 Answer

Switch abs on or off how do i know it is on or off

There is a switch on the left side and during start up abs flickers on and off. How should I interpeted that flashing ABS and how do I switch it off.
(ABS) can that be done during the ride ?

Posted by mallon87 on

Ad

1 Answer

Anonymous

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 948 Answers

When the bike first starts the ABS circuitry is tested and the light should go out within a few seconds. The ABS can not be turned off while the bike is in motion, you must come to a stop for that. Consult your owner's manual for the specific procedure for deactivating the ABS. Once it is deactivated your light will flash very slowly until the system is reactivated or the bike is turned off.

Posted on Jun 19, 2009

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 ml500


The dealer has to know how to diagnose ABS System problems

They have to drive it first & you should drive with them along, then
switch seats,do that

Nov 28, 2012 | Cars & Trucks

1 Answer

Hi there, I have a 2005 Infiniti QX56 which got a unique little problem with the lights in the dashboard. While the light setting is on Automatic and during night driving, the lights in the dashboard...


Have a look at the dashboard lights dimmer switch. That switch, losing contact momentarily while the lights are on, will cause the lights to flicker.

May 06, 2011 | 2006 Infiniti QX56

1 Answer

On a 2004 Lincoln Navigator. Where is the suspension compressor relay located. My vehicle was working fine. After I stopped to get something to eat, as I turn my vehicle On the lights flickered and the air...


Okay the switch is in the back trunk area(I know it a SUV) in the back where you access the jacking tool youll see the switch make sure its on. Now some Navigator some have a shrader valve to pump up the suspension on the front area on driver side. As for the relay you might have to use a enhance scan tool to command it.By the way do you have a misfire?because if there is a misfire it will not inflate or a ABS light on? thse will also cause the suspension to not inflate

Apr 23, 2011 | 2004 Lincoln Navigator

2 Answers

Handbrake warning light flickers on and off when the handbrake is off.?


The brake light will illuminate when the hand brake is on and when the brake fluid is low. Have you checked to make sure the brake fluid is full in the master cylinder reservoir?

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Jan 11, 2011 | 2006 Kia Sorento

1 Answer

Lexmark P3150 was working fine.But paper got jammed. I pulled the paper out and color cartrdge went to left side like a bullet and blue light in On Off switch started flickering. When I start printer...


Maybe you somehow detached the encoder strip when removing the paper.
First, before you put your hands inside the printer, unplug the power chord from your printer. This is important.
Then open up the lid and locate the horizontal metal bar.  Right above this there should be a semi-transparent plastic strip attached in the right and left side of your printer. If you see this, try moving it with your finger. If its properly attached, it should bounce back to it's original position. If it's loose, try to attach it to the right/left side again. If you can't find it, it probably fell off and is jammed inside the printer somewhere. 

If the encoder strip looks OK, your carrier might have jammed in the left side of your printer. Keep the power chord unplugged. 
See if you can unjam the carrier by pulling it along the metal rod. If should be fairly easy to move back and forth, so you'll know if it's stuck. If you can't loosen it, your printer is probably damaged beyond repair. Check if you have warranty on it. 

Mar 05, 2010 | Lexmark P3150 All-In-One InkJet Printer

1 Answer

I have a 2001 ford windstar the battery light the


thier is problem with brake switch on master cylendre leaks brake fluid on top a abs madule and short the wires need to change switch, plug ,and abs madule

Oct 31, 2009 | 2001 Ford Windstar

1 Answer

Switch off ABS


If you've got a ABS light on, you either have a failing ABS sensor, or an unsafe condition with the ABS. Your Town Car may have 2 ABS lights, one left and one right to leet you know which side is faulty. Either check for a bad sensor (they can go bad, it's basically an electrical cord that plugs into the top of the caliper) or have the brakes checked by a mechanic.

Jul 14, 2009 | 1998 Lincoln Town Car

Not finding what you are looking for?
2006 BMW R 1200 GS Adventure Logo

548 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Arnie Burke
Arnie Burke

Level 3 Expert

6480 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

217 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...