Question about 2007 Kymco Venox 250

1 Answer

Wont Start I believe I need to clean/change my spark plugs. Specifically, how do I get to them and change them? The description and pics in the owners manual are not the best. PLEASE HELP ASAP!!

Posted by Neptune Pringle III on


1 Answer


  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

There is one sparkplug at center front of engine and one at center rear. They are fairly easy to change. Just follow your spark plug wires.

Did the vehicle set up for a long period and did you use a fuel stabilizer in the fuel.

Posted on Mar 25, 2014

Testimonial: "It was not sitting for a long time, but it has been very cold. I hooked up my battery recharger/maintainer. The battery is fine. No fuel stabilizer. I'm going to try this today."


Add Your Answer


Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Still 100 brushwood cutter wont start.please suggest a procedure for identifying the problem

change the spark plug be sure it is clean and set at .030. if it dont start take plug out and ground it to the metal engine block pull the rope you should see spark. if you have spark spray a shot of carburetor cleaner in the opening of the carburetor. if it starts and dies in a few seconds you need to take the carburetor off and clean it.

Jun 16, 2016 | Stihl Garden

1 Answer

EB4035HG wont start

because of the vague description I will go through my thought process. Does it have gas? Is the oil filled? Does it have spark?If not change plug ...If still no spark disconnect the Low oil prob(yellow wire coming from side of engine block to the on off switch) Still no spark then it is the coil...Has it been sitting for a while? Possibly gas has gelled inside the carb...clean the carb and jet out thoroughly. Finally, if all that passes...then try to start the engine while triggering the wand...If ti starts you have either a clogged tip or a bad unloader on the pump. Good luck

May 05, 2014 | PressurePro Eagle EB4035HG Pressure Washer...

2 Answers

Car not starting, whirring once ignition engaged

Check the obvious. Shift to park (also try neutral) If you jump from the battery to the starter directly if it turns then you may need to replace the solenoid. It may also be an ignition that needs to be replaced.

Nov 18, 2013 | 1999 Mitsubishi Mirage

1 Answer

Wont start

I would check for spark, if you have spark put a little bit of carb cleaner in the spark plug hole and see if it fires up and then dies. If that is the case then the carburetor needs to be cleaned. Hope this helps!

Jun 07, 2012 | Troy Bilt 5.5hp Self Propelled Mower

1 Answer

94 lexus sc300, Been sitting for 3years. was running fine when parked. Recently need to use car again. I changed out the old fuel with new fuel. replaced battery. Car turns over but wont start. I am...


Oct 24, 2011 | 1992 Lexus Sc 300

3 Answers

2007 nissan titan turns over but wont start no spark to the plugs .

The problem could be in the spark plugs. Usually if just one of the spark plugs is not producing the spark needed, the engine would still start. It may run rough, but will still start. If none of the spark plugs are producing a spark (or firing) then this could be the culprit.The spark plugs gets power to spark from coil packs.So check the coil pack first.If the coil pack checked ok then its faulty spark plugs causing this problem.Also remove the spark plug connection and clean it and reconnect it and recheck.In some cases this helps. ---------------That's it.

Nov 18, 2010 | 2007 Nissan Titan LE

3 Answers

My 1989 suzuki sidekick cranks but wont start. I changed the battery too.

you need to go step by step threw your system. first check the spark plugs to see if there is any moisture if so all bad. check wires to plugs and clean contacts inside distributor cap. check compression on each cylinder. they should be with in 10 psi of each other. check to see if there is even any juice being fed to the distributor. if there is no spark you need to fallow it back to the source until you find the problem.

Jan 25, 2010 | 1989 Suzuki Sidekick

2 Answers

Moped wont start

is there a spark a decent one if not try changing plugs if still no spark it could only be the cdi,coil and magneto get back to me buddy

Sep 13, 2009 | 2005 Tomos Se 125 F

1 Answer

Will not start changed the crank shaft sensor will not start changed the crank shaft sensor still nothing injectors wont go to and no spark any ideas please

It could be a computer malfunction or a circuit in the ignition switch has went on you. By the description I get that the spark plugs and the injectors are not working?

Jun 10, 2009 | 1997 Dodge Caravan

2 Answers

Lawnmower wont start

Possible Causes Corrective actions
Unit will not start Control handle is not engaged Engage control handle spacer.gif spacer.gif
Spark plug wire is disconnected Connect spark plug wire spacer.gif spacer.gif
Fuel tank empty or stale fuel Replace with clean, fresh gas spacer.gif spacer.gif
Blocked fuel line Clean fuel line spacer.gif spacer.gif
Faulty spark plug Replace, clean, or adjust gap spacer.gif spacer.gif
Engine flooded Wait to restart, do not prime spacer.gif spacer.gif
Air filter filled with dirt or debris Replace or clean air filter

May 23, 2009 | Mtd 22" Yard Machine Push Mower

Not finding what you are looking for?
2007 Kymco Venox 250 Logo

165 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kymco Experts


Level 3 Expert

85239 Answers

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

6480 Answers

Are you a Kymco Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides