Question about 2002 Kymco Stryker 125

Open Question

Replace the steering lock 2002 Kymco Stryker 125

Kymco 125 how do I fit new steering locks and barrel @

Posted by Anonymous on

Ad

5 Related Answers

michael wiggins

  • 135 Answers

SOURCE: I HAVE A MERCEDEZ 190 AND THE KEYS ARE NOT TURNING

it is better to buy a new ignition barrel.it takes a special socket to get the screws out, once the screws are out they do not need to be replaced.buy new barrel,disconnect negative battery cable,disconnect wires from barrel assembly, remove barrel from colum. first take vin# to dealership parts department to get correct barrel assembly, the keys with new assembly will fit doors and trunk

Posted on May 20, 2009

Ad

Anonymous

  • 7 Answers

SOURCE: battery keeps loosing charge- kymco cruiser 125, 2005

I had this exact same problem on a hipster 125, it was a faulty regulator module ( mounted under the seat) I also found a short circuit (somewhere) in the wiring loom between the regulator output and the chassis (probably what killed the regulator in the first place!) I cut and replaced the entire wire to save removing most of the loom and after testing reg to ensure it was dead i fitted a new one (about £60) bike charges and runs like a dream now even with fully lights approx 80% of the time. good luck

Posted on Jul 23, 2009

Ad

Anonymous

  • 14 Answers

SOURCE: Program new key

do u meen the code key you can swap chips over just put a needle through the tiny hole in the swing out chip holder u will no wot i meen my frend gd luck

Posted on Apr 16, 2010

Anonymous

  • 1 Answer

SOURCE: I lost all keys for my Piaggio Fly 125 /2007 Y/

I know this response is a little late. However if anyone has Vespa or piaggio lock problems, i would be happy to help. I am a locksmith with a passion for Vespas. I work, cut keys and rekey piaggio locks daily.
Cheers, Jim
www.allmotorcyclekeys.com

Posted on Jan 16, 2011

gilly dna125

  • 1 Answer

SOURCE: i have recently lost the keys to my gilera runner

Bang a screw into the key lock with a claw hammer an then use the claw to pull the screw out with the barrel on the end of it

Posted on Jul 13, 2011

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Hi I need to find out how to fit the new tyre on my KYMCO CK 125 I bought the correct tyre but it seems impossible to fit also can I repair a puncture in the tube or do I have to by new?? any advice pls


keep it pushed dowm just passed center use fairy liquid to make it slipper for you. your puncture sand the aera blow off use only a pacth & soluition for automotive purpous apply soluition and leave dry almost like only the glase gone off it peel off the back off the pacth and stick rub it well in

Jul 13, 2011 | 2005 Kymco 125 Pulsar CK

1 Answer

I have an Isuzu Rodeo and the key is stuck in the ignition any idea how to get it out? Year 2000


replace the whole ignition barrel with new key and get key programmed by dealer
can remove barrel and key by removing steering column covers turn ignition to on position and with small shank screw driver push in hole in outer top rear section of barrel assembly then pull out ignition lock barrel with key in it. fit new lock barrel and key, program new key into system and can get door lock barrels coded to suit new key or get code for old key and cut new key so it fits mechanical locks on the rest of the vehicle (just wont turn in ignition) 2 keys for vehicle.

Jun 13, 2010 | 2000 Isuzu Rodeo

1 Answer

I have lost my keys can they be replaced


hmm i dont think its possible the only way to do it is hot wire the bike or by a new ignition barrel which will come with new keys

Nov 02, 2009 | 2001 Kymco Stryker 125

2 Answers

Battery keeps loosing charge- kymco cruiser 125, 2005


I had this exact same problem on a hipster 125, it was a faulty regulator module ( mounted under the seat) I also found a short circuit (somewhere) in the wiring loom between the regulator output and the chassis (probably what killed the regulator in the first place!) I cut and replaced the entire wire to save removing most of the loom and after testing reg to ensure it was dead i fitted a new one (about £60) bike charges and runs like a dream now even with fully lights approx 80% of the time. good luck

Jul 14, 2009 | 2005 Kymco Hipster 125

1 Answer

I HAVE A MERCEDEZ 190 AND THE KEYS ARE NOT TURNING IN IGNITION BARREL NOW THE STEERING IS LOCKED ALSO I HAVE TAKEN OUT IGNITION BARREL WITH STEERING COLOUM. i WOULD LIKE TO DISINGAGE THE IGNITION BARREL...


it is better to buy a new ignition barrel.it takes a special socket to get the screws out, once the screws are out they do not need to be replaced.buy new barrel,disconnect negative battery cable,disconnect wires from barrel assembly, remove barrel from colum. first take vin# to dealership parts department to get correct barrel assembly, the keys with new assembly will fit doors and trunk

May 19, 2009 | 1993 Mercedes-Benz 190

3 Answers

Oil bolt has rounded of what size is the bolt??


fit in a helical, and keep in the same bolt, that should solve your problem

Feb 18, 2009 | 2005 Kymco Stryker 125

Not finding what you are looking for?
2002 Kymco Stryker 125 Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kymco Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

6480 Answers

Are you a Kymco Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...