My key in my scooter wont turn to the on position

If the lights on your Golden 3-wheel scooter won't turn off and you hear a beeping sound after turning it on, it could indicate a potential issue. Here are some troubleshooting steps you can try:

1. Check the key switch: Ensure that the key is inserted fully into the key switch and turned to the correct position. Sometimes, if the key is not fully engaged or turned properly, it can cause electrical issues. Try removing the key, reinserting it, and turning it to the correct position.
2. Examine the battery connections: Inspect the battery connections to ensure they are secure and free from corrosion. Loose or corroded connections can affect the scooter's electrical system. If you notice any loose or corroded connections, carefully tighten or clean them as needed.
3. Verify the charger connection: If the scooter is connected to a charger, make sure it is properly plugged in and connected to the scooter. A loose or faulty charger connection can cause electrical malfunctions. Try unplugging and reconnecting the charger to ensure a secure connection.
4. Check the scooter's manual: Refer to the owner's manual or user guide for your specific model of Golden 3-wheel scooter. It may provide troubleshooting steps or information about the beeping sound and lights issue you are experiencing. Look for any error codes or indications that can help diagnose the issue

Amigo Scooter Oxygen Tank Holder Light flash key turned ...

www.fixya.com > ... > Amigo > Amigo Scooter Oxygen Tank Holder
... key on my phoenix 3 scooter the red light flashes 5 times and the scooter will ...scooter wont move,although on the little speedo there is a red light flashing on ... ...light is flashing when the key is turned on. the scooter does not move at all ... flash up and down the console light and you at this point have to turn the key off ...

My pharmore wizard diagnostic light flashes 9 times and my ...

www.fixya.com/.../t25197681-pharmore_wizard_diagnostic_light_flashe...

Oct 8, 2014 - my pharmore wizard diagnostic light flashes 9 times and my scooterdoes not go, can someone help me please - Mobility Scooters question. ... Have no manual for pharmore 4 wheeled wizzard light on but wont move ... Why did it stop working suddenly and is blinking console light in 5-blink sequence?

Hi if it is similar to pride x the circuit will shut down if key is left on for 20 minutes u will still have lights. Remove key for a short time then replace it & turn on ..goood luck

Could have a wiring issue you should look in the console make sure nothing is crossed.

Look at the freewheel lever on the rear of the scooter. Make absolutely sure it is not in the disengaged position.

Tryi this it may help

1

Make sure the vehicle is balanced on the centerstand. The centerstand is a metal bracket located in the middle on the bottom of the scooter. Engaging it means that the scooter is resting on the front tire and centerstand. The rear tire is raised slightly off the ground.

2

Insert your ignition key into the main ignition switch. The switch is located on the inside front of the scooter just to the right of center and below the handlebars.

3

Twist the key to the left, or counterclockwise, to the position on the switch marked Open. If the scooter is not in the locked position, turn the key to the first Open position. If the scooter is in the locked position, turn the key to the second Open position. In either case, turn the key counterclockwise one notch to the respective Open position. The Yamaha Vino Scooter Owner's Manual cautions you that you should not push down on the key while turning to the Open position.

4

Grasp the end of the seat nearest the front wheel and pull it upward to raise it on the hinges located at the rear. Now you can store or retrieve items from the storage compartment

hi, there is a fault finder at the back of the manual, 5 flashes means the drive motor is not coonected, check that the freewheel lever at the back of the scooter is in drive then turn off and on again with the key, hope this helps. Bill

Hi
Please Check that your Freewheel Lever is Fully in Position as if is Slightly out of Position it will Not Work,

Gerry.

Hi, I take it been taken then, do you get a error codes ?

see below


DIAGNOSTIC FLASH CODES
The diagnostic flash codes for your scooter are designed to help you perform basic troubleshooting quickly and
easily. A diagnostic flash code will flash from the status LED in the event one of the conditions listed below
develops.
NOTE: Your scooter will not run unless the flash code condition is resolved and the scooter has been
turned off, then turned back on.
Any electromechanical device occasionally requires some troubleshooting. However, most of the problems that
may arise can usually be solved with a bit of thought and common sense. Many of these problems occur because
the batteries are not fully charged or because the batteries are worn down and can no longer hold a charge.
FLASH CODE CONDITION SOLUTION
! (1) Battery charge is low. Charge batteries as soon as possible.
! ! (2)
Batteries are too low to operate the
scooter.
Charge batteries.
! ! ! (3)
The scooter’s battery voltage is too
high to operate the scooter, or the
charger is still connected to charger
port.
Unplug charger and/or turn key off, then
back on again.
! ! ! ! (4) Current limit time out.
Turn the scooter off for a few minutes,
then turn your scooter back on.
! ! ! ! ! (5)
The manual freewheel lever is in the
(forward) freewheel position.
Remove the key from the key switch,
then push the manual freewheel lever to
the (rear) drive position, and restart your
scooter.
! ! ! ! ! ! (6)
Throttle control lever not at center
position at start up.
Return the throttle control lever to center
position, turn scooter off, then back on.
! ! ! ! ! ! ! (7) Speed pot error.
Contact your authorised Pride Dealer for
assistance.
! ! ! ! ! ! ! ! (8) Motor volts error.
Contact your authorised Pride Dealer for
assistance.
! ! ! ! ! ! ! ! ! (9) Other internal errors.
Contact your authorised Pride Dealer for


Regards
GeWiz.