Question about Motorcycles

1 Answer

How do i take apart my motor on a yamaha blaster 200cc motor

Posted by roy stennette on

Ad

1 Answer

Gregg Mahin

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    One Above All:

    The expert with highest point at the last day of the past 12 weeks.

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

  • Motorcycles Master
  • 64,934 Answers

Hi, Ropy you need to repost your question under the Yamaha Blaster ATV category, not Motorcycles. Thanks, Gregg

Posted on Aug 06, 2020

Ad

3 Related Answers

Anonymous

  • 5 Answers

SOURCE: i have a 96 yamaha blaster 200cc atv. Its not

I have a 96 blaster just had the top end done 80 over new piston and rings. Ran good for 2 hr and stopped running. I have good conpression but no spark. Put in new plug still no spark.Is it the coil or the magneto?Where is the magneto and how do I replace it?

Posted on Aug 30, 2009

Ad

paulattard

  • 205 Answers

SOURCE: hi i have a 2004 yamaha blaster that is only a

Coil? how about the battery?

Posted on Jan 06, 2010

John Fourteen Six

  • 2418 Answers

SOURCE: my motor will start but

If old gas sat in the carb. for more than a month it starts to dry up. As it drys up it leaves behind a varnish like film that stops up some very small ports and pin holes inside a motorcycle carburetor. It is also very hard to get out. You can try this. Use a product called Seafoam, get as much gas out of the carb.s as you can. use a turkey baster and force the seafoam into your carb. Take the fuel line loose from the fuel tank and force it into the carb(s). Let that set for say 1 or 2 days. then hook up the fueltank with a mix of good gas and seafoam, (not a lot but enough to start it up. Move the cycle outside as the seafoam will make a lot of smoke if it does start up. If that does not clear up the problem you may have to pull the carb. and remove the blows to clean the inside, I know you said you have already done this but you may have to do it again, and pay attention to very small holes in the up tube . If you have to do that do not DO NOT MESS with any adjustment screws. Just take the carb. bowl off. Do not mix up any internal parts. It is best to work on a large sheet so if you drop a small part you can find it, you do not want to be missing some tiny spring or screw. Hope this Helps Fix Ya Up..

Posted on Aug 14, 2011

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi guys, i have a 2004 yamaha blaster (200cc) and its all stock standard. I once took it in to get it serviced and it came back with about 12 holes in the air filter box cover. I went and bought a new...


Make sure your air cleaner is clean and not restricting the air flow. try removing it completely and then run it and see if there is any difference.Also make sure your carb is clean! The holes that were drilled in it is a way to modify the air box for better performance by allowing more air but the down side is you might get water in your motor if your running through mud and water

Dec 26, 2014 | Motorcycles

1 Answer

2006 yamaha blaster 250


is it getting spark? did you check the compression?

Jun 17, 2012 | RTO 200cc Full Size Four Wheeler ATV

1 Answer

WEAK FIRE


check cable, spark plug, spark plug cap for good resistance levels. then check the coil. easy fix.

May 15, 2012 | RTO 200cc Full Size Four Wheeler ATV

1 Answer

I have a 2005 yamaha blaster and it cranks but it knocks really bad and when you press the gas it shuts off. We have cleaned the carborator and jets, taken the motor apart and everything. Inside the m


Hi Jennifer_384, for this situation I would call my local dealer or reputable shop's service/parts department and inquire about any possible quick fix or parts inquiry. If necessary transport your vehicle to the dealer or shop and have a professional technician take it for a test drive, if it is in running condition, and give you a written estimate of repairs and answer any specific questions you may have about your issue. Good luck and have a nice day. 2005 Yamaha ATV Service Repair Workshop Manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Jan 24, 2012 | Motorcycles

1 Answer

I just bought a used 2000 yamaha blaster 200cc 4-wheeler and the side of the engine that has the kick start has a tube in the top of the crank case that looks like some kind of maybe vacume tube or dip...


Here is your manual. Read it from end to end. The tube is probably a crankcase breather tube. The piston going up and down creates varying suction and pressure at the underside. The breather normally terminates up under the gas tank.

http://www.yamaha-motor.com/assets/service/manuals/2001/lit-11626-14-09_246.pdf

Jul 31, 2017 | Motorcycles

2 Answers

1989 yamaha blaster does not stay on


mcdevito75 here, Sounds like a lack of spark to the spark plugs to me, have a shop check it out for you, menwhlie you can check all around your Yamaha blaster for any wires loose or not connected.

May 24, 2010 | RTO 200cc Full Size Four Wheeler ATV

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

6480 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...