Question about Harley Davidson Motorcycles

1 Answer

How do I remove my left side gas cap - Harley Davidson Motorcycles

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    One Above All:

    The expert with highest point at the last day of the past 12 weeks.

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

  • Harley Davidson Master
  • 60,971 Answers

Hi Anonymous, you could have a faulty sending unit or guage, there could be a problem with your wiring. On models with the fuel gauge posing as a left hand fuel cap the gauge is a press fit do not try to unscrew it, simply ample force lift up in a rocking motion to remove gauge. Disconnect wires to the gauge and with a set of positive and negative jumpers from the battery connect the positive jumper and flash the negative, gauge should peg full, if not replace gauge. With a test light check for power to the sending unit, then remove the sending unit and manually operate the float arm slowly with the correct wiring hooked up to the fuel gauge and sending unit and the ignition on, the gauge should respond accordingly if not replace the float arm assembly. For a free wiring diagram please visit the website below and good luck.
Harley Davidson Wiring Diagrams and Schematics

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Posted on Jun 06, 2015

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to remove gas tank on 2003 ultra classic electric glide


1. Drain fuel tank as follows:
Obtain a short section of hose with a 5/16 inch (7.9 mm) I.D.
Insert bolt in one end of hose and install hose clamp to
ensure that end is securely plugged. Using a side cutters, cut
clamp from one end of crossover hose beneath fuel tank.
Quickly replace crossover hose on fuel tank fitting with open
end of short hose while directing flow of gasoline from free
end of crossover hose into suitable container.
2. Remove seat.
3. Purge the fuel supply line of high pressure gas. Proceed
as follows:
a. Remove the 15 amp fuel pump fuse.
b. Start the engine and allow the vehicle to run.
c. When the engine stalls, operate starter for 3 seconds
to remove remaining fuel from fuel lines.
4. Unthread bolt and remove battery negative cable (black)
from battery negative (-) terminal.
5. Carefully cut anchored cable strap securing main harness
bundles, console pod conduit, fuel level sender/fuel pump conduit, and fuel vapor vent tube to left side of frame backbone.
6. Open fuel door on console. Remove two Allen head
screws inboard of rubber bumpers. These screws
secure console to clip nuts on the canopy bracket.
7. Remove Allen head screw to detach flange at rear of
console from clip nut on fuel tank weldment.
8. Lay a clean shop towel on forward part of rear fender.
9. Remove filler cap from neck of fuel tank. Remove console
and lay upside down on shop towel. Reinstall filler cap.
10. At top of canopy, depress button on socket side of 3-
place Mini-Deutsch connector to release fuel tank harness.
11. Gently pry fuel vapor vent tube from fitting on filler neck
of fuel tank. Exercise caution to avoid pulling fitting from
filler neck.
12. Locate quick-connect fitting on left side of fuel tank. Pull
up on chrome sleeve and pull down on fuel supply line
fitting to disconnect.
13. Remove two fuel tank front mounting bolts (with flat
washers) from left and right side of frame. Remove bolt
(with flat washer) to free rear of fuel tank from frame
backbone.
14. Remove fuel tank from vehicle.

Jun 29, 2014 | 2003 Harley Davidson FLHTCUI Electra Glide...

1 Answer

How do I remove the cap on the left side of the gas tank. Side where gas gauge is at.


Unhook the connection under the gas tank. Remove the pins from the elelectrical connection for the fuel gauge. Pull the gauge up. It is held in place with a piece of plastic that surrounds the gauge housing. Good luck!

Apr 11, 2013 | 2005 Harley Davidson FLSTC - FLSTCI...

1 Answer

2005 hertigae soft tail how do i remove the cap on the left side of the gas tank


Depending on how your bike is setup and IF it's an orginial tank or aftermarket tank on the bike, one of the caps are basicallly a dummy cap, (For Looks) and is NOT removable.

Apr 11, 2013 | 2002 Harley Davidson FXST Softail Standard

1 Answer

Where is the gas filter located on a 2002 S60--4dr.


Removal & Installation


NOTE

The fuel filter is either on the left side of the firewall or next to the fuel pump near the left side of the fuel tank.


  1. Before servicing the vehicle, refer to the Precautions section.
  2. Relieve the fuel system pressure.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Fuel filler cap
    • Fuel lines from the fuel filter
    • Fuel filter from the bracket

To install:

  1. Install or connect the following:
    • Fuel filter to the bracket
    • Fuel lines to the fuel filter
    • Fuel filler cap
    • Negative battery cable
  2. Start the engine and check for leaks.
  3. 7923xg11.gif

Oct 23, 2010 | 2002 Volvo S60

1 Answer

My wife has a 2009 Softtail Delux. When we fill the gas tank and then ride it, gas runs out aroung gas cap onto tank and onto rider. I have tried not to fill it all the way and it still does this. It seems...


I don't know if there's a recall on this but it sounds like your gas cap is not screwing all the way down to get a seal. There are right side and left side caps on her bike. The right side is the vent cap. Someone may have put a vented left side cap on her bike. Gas cap swaps or thefts are common because there's no way to secure them. Don't ever buy a nice set of billet caps as they might not be on your bike when you leave it unattended the first time.

Good Luck
Steve

Aug 31, 2010 | Harley Davidson FLSTN- FLSTNI Softail...

2 Answers

I need to refill radiator on a 2007 suzuki boulevard c50 how?


To access the radiator cap, remove the seats,then the bolt at the rear of the gas tank. You should now be able to slide the entire tank and dash back enough to expose the cap on the left side of the frame. When replacing the tank, be careful not to knock loose the rubber buffers that slide into grooves on either side of the frame.

Jun 14, 2010 | 2005 Suzuki Boulevard C50

1 Answer

How do I drain gas from tank craftsman ys 4500?


disconnect fuel line from fuel filter, snake fuel line over to left side of engine. Remove gas cap and fuel will empty out of fuel tank.

May 15, 2010 | Craftsman 21 Hp 42" Deck, Ys 4500 Lawn...

1 Answer

Pop the top miele t9820 dryer gas


Open the door, at the top of the recessed door opening you will see two round plastic caps. Remove these and you will see screw behind that you have to remove. Some models the caps are on the right and left hand sides. Slide the top towards the back after removing screws and the top will lift off. Good Luck, Appliance Specialists

Jan 06, 2010 | Miele T9820 Gas Dryer

1 Answer

I am waiting for circuit board part to be delivered. I have tried to disconnect wires from behind remote control (didnt work). Is there any other way to jump start hot water until my part arrives?


If you open the cover and look at the PCB ther're four capacitors on the left hand side of the board - If the tops of thos caps are slightly raised...ther're blown - you'll have to replace them to get the unit to work.

Parts are available at radio shack or Allied Electronics - or you could find a supplier in your area.

To replace the caps 1)Unplug/remove A/C power. 2)Label and remove all electrical connections to the PCB and remove the PCB from the water heater unit. 3)With the PCB sitting on a flat surface...rotate PCB until the single silver screw is in the top left corner (the caps in question should be in the mid portion of the PCB and on the lefthand side facing the board. 4)Remove the screw from the top left corner...firmly hold the plastic case containing the PCB and gently start bending the plastic case back, until the silicone protectant starts to separate from the plastic on all four sides. Once you have the silicone separated the PCB should pop out of place with some gentle nudging. 5)Remove the protectant from around the caps and remove from the associated area on the back as well. 6) De-solder and replace caps (2 ea/670X25V and 2 ea./220X35V) - available at electronics supplier.

Nov 14, 2009 | Rheem Paloma PTG-74PVN / RTG-74PVN...

2 Answers

I have a goldwing 82 interstate gl and would like to know how to access the radiator cap. I can't see it through the fairing?


Remove the seat,them remove what looks like the gas tank.You should be able to get to cap then.
Eric

Sep 23, 2009 | 1982 Honda GL 1100 Gold Wing

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

6156 Answers

Mike

Level 3 Expert

4369 Answers

Marvin
Marvin

Level 3 Expert

85223 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...