Question about Motorcycles

Open Question

Derbi fenix Hi, My son has a 2004 Derby Fenix 100. Great bike but he bent the front end! Where can I get front forks from, or will any other forks fit? Any help will be welcome thanks.

Posted by Anonymous on

Ad

5 Related Answers

tombones

  • 3567 Answers

SOURCE: can i fit forks from a different bikes

Yes, forks can be swapped in some cases. First, the diameter of the replacement forks must be the same as the old forks. The length of the forks will need to be close to the original also. Often the entire wheel and brake assembly must change also because the brake hub from a Honda will not fit Suzuki forks. The speedometer may also be a factor because the old cable may not fit the new hub.

Try a salvage yard. Google " motorcycle salvage suzuki " and see what you can find/

Can I get a “very helpful” rating on this answer? < And it doesn’t cost anything extra!

Posted on Jul 06, 2009

Ad

Anonymous

  • 53 Answers

SOURCE: Bent Shifting fork?

dear swedishpytho the bic engine will have to be removed and split to expose the trany. you can likely do this job yourself but is is a big job reguiring shiming the shift forks and gears .the problem is likely a worn shift fork. a repair manual is a must for this job. the cost of parts i am not sure but beside the shift fork a complete gasket set will be reguired,and since the engine will be striped down you might as well rering the engine hope this helps jim

Posted on Apr 12, 2009

Ad

Anonymous

  • 69 Answers

SOURCE: leaking oil out of the primary derby cover any suggestions

Either try a new gasket or get the right derby cover

Posted on Jun 28, 2009

Anonymous

  • 1 Answer

SOURCE: torque specs for derby , inspection cover, &

what is the torque specs for a derby cover on my 2009 Soft tail?

Posted on Jul 27, 2009

DoubleClutch

Greg O'Day

  • 376 Answers

SOURCE: i bent my shifter fork ,bike jumps outa 2nd now

Sorry the only way to get to the shifter fork in the trans is to remove the engine and take the top end off and split the case's. That's a huge job and cost's allot to do.

Posted on Oct 16, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

This thing suxs


Right about 1 quart (give or take about and fluid ounce or two).

Two ways to judge:

1: hold bike upright, remove derby cover (over clutch pack).
Pour primary fluid through derby cover hole until level comes up to just the bottom of the clutch plates.

------------------------OR-------------------

2: With bike on kick stand, pour fluid through derby cover opening until level is just below the derby cover opening.

Apr 17, 2014 | 2006 Harley Davidson FXDBI Street Bob

1 Answer

Can you open the switch end of fenix hl21?


the plastic will break and even if you do get access to that, the issue with the corrosion will still cause problems.

Nov 24, 2013 | Fenix Flashlights Black HL21 Fenix HL21...

1 Answer

Back to the drawing board You guys almost got us killed ([email protected]) I won't hold my breath for your response


in most cases you can here it when the key is turned on you could do a pressure test if you know someone with a tester or a garage does not charge to much to test it

Jan 24, 2013 | Garmin fenix - GPS receiver

1 Answer

I have a Fenix TK15 that doesn' light up. I have changed batteries, still no light


Hi marlyn engaling...
Sounds like you need to replace your bulb, it may be burned out.
Also check the switch and also make sure the spring in the back of the flashlight is touching the battery tightly to make good contact.
Bud

Sep 18, 2012 | Fenix TK15

1 Answer

Fenix hp11 headlight


Hi, I have some experience with this unbekievable good headlight(when it works).
I had a hp10 what started to stop more and more.
After a while it wasn't going on.
5 years warrenty, so i got a new one, the new model.hp11
The main problem is the wire from battery case and the head led.
When there a litte damage inside this wire, light goes of not going on it selfs when it connecting again. After a while it will not work any more.
(if you have a welding station you fix it your self (battery case,can go open by unscrew the wire entrance.)

Chack battery case if the springs are all still connecting the battery.
If you put in one battery false on there is short cut and al sprigs get so hot they will shrink. And stay in that position..fix that your self or ring/ contact the shop you bought it.
There 5 year of garrantie.
wonderfull

Jul 25, 2012 | Fenix Camping, Backpacking & Hiking

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

6480 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...