Question about Motorcycles

Open Question

How to replace impeller on tohatsu m25c3

Two stroke tohatsu out board motor m25c3

Posted by Anonymous on

Ad

1 Related Answer

John Fourteen Six

  • 2418 Answers

SOURCE: impeller replacing on 1999 merc. 25hp 2 stroke

Should not be that hard. Tape up the ends so you can hold it with out getting cut, (if its ragged or sharp from damage). should be one nut holding the impeller on. If its to tight to hold try air or electric Impact wrench. If its bad you can tap with a hammer to help in removing the old one. If it turned on the shaft you will need to rent a puller. Repost if you need more help.

Posted on Jul 05, 2009

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I am wondering if I can retrofit an electric tilt to my Tohatsu 9.8 4 Stroke outboard.


very possibly can
if there are 2 small shockys in the mount , the rams will fit in their place and the rest is academic as to fitting
You should be talking to a Tohatsu service dealer as they have all of the ideas as to the fitment procedures

Feb 14, 2018 | Boating

1 Answer

To extend leg 6 inches on a tohatsu 90 hp m90a boat motor do i replace the drive sharft or put an exta ension n


fit a longer leg section to the power head
talk with a tohatsu service agent for the longer leg

Dec 28, 2017 | HP Boating

1 Answer

How can I find or locate the year of the motor? Have 25 horse electric start 4 stroke.


Yamaha, Suzuki, mercury, Evinrude, Johnson, Tohatsu???

On your transom plate or swivel bracket you'll find a sticker with exact engine make, type and serial... Please give the right and complete information!

Oct 17, 2017 | Electric Boating

1 Answer

Bought a 40hp two stroke had new inpeller only pumps now an then


Replace the impeller again. The impeller is spun (rubber from brass sleeve) or key is sheared or missing or it was installed in the wrong rotation of the motor and fins are damaged. The housing (stainless dish) is damaged or alignment tube is off.

Jan 16, 2017 | Boating

1 Answer

Misfire on Tohatsu outbaord.


one would assume so but as you have not mention if it is a 2 stroke or 4 stroke , that assumption would possibly be wrong
2 strokes use reed valves between the carby and manifold and the crankcase and in outboards these reed valves can split and not function properly especially at higher prms
these reed valves allow fuel mixture in when the piston goes up and shut off when the piston comes down creating a pressure in the crankcase which pushes the mixture up the bypass of the cylinder into the combustion chamber
if these reed valves are not working properly or the crankshaft seal are failed this compression in the sump doesn't occur properly and engine running problems result
IF it is a 4 stroke the soaking the carby in cleaning fluid will only remove 1/2 the problems
It is best to have the carby fully overhauled by an accredited outboard mechanic as there will still be corrosion in the body and mixture passages that cleaning fluid alone will not remove.
have the ignition system checked as it may be an overheating component ( coil --ignition module) that is causing the failure.

Aug 11, 2015 | Boating

1 Answer

I have a new Tohatsu 6HP, 4-stroke motor on a sailboat. Is there a secret to starting it without pulling on the d... cord 20 times? Even then it may not start. Kind of scary if I am out on the lake and...


Yes, I think I know the problem because I have the same motor and mine starts right up every time. When you cold start it, you may not be priming it enough...it doesn't have enough gas. Don't squeeze the bulb 2 or 3 times, do it about 10-12 times. Full choke and it will light right up. On a warm start, you don't need to prime it or choke it. On a semi-warm start, try half choke and no priming.

Jan 11, 2010 | Light Outboard Motor Boat Bass Fishing...

1 Answer

Empty hole(s) on carb


That should be where the high...low speed air mixture screws should be...look inside close and see if they are in there..

Dec 13, 2009 | Boating

1 Answer

Impeller replacing on 1999 merc. 25hp 2 stroke


Should not be that hard. Tape up the ends so you can hold it with out getting cut, (if its ragged or sharp from damage). should be one nut holding the impeller on. If its to tight to hold try air or electric Impact wrench. If its bad you can tap with a hammer to help in removing the old one. If it turned on the shaft you will need to rent a puller. Repost if you need more help.

Jul 04, 2009 | 1999 Honda XR 600 R

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

6480 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...