Question about 2008 Derbi Senda XRace 50 SM

Open Question

How to tighten chain on mopeds - 2008 Derbi Senda XRace 50 SM

Posted by Anonymous on

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My stihl ms-180-c chain saw will not keep chain tight. you tighten chain rev. engine chain will just about come okk -tighten chain rev. engine same thing.


you have to use the tension screw to move the cutter bar to tighten the chain then you do up the bar mounting nut to keep it tight

May 12, 2017 | Stihl Garden

1 Answer

After you install bar,chain,and brake cover(tightened)the chain wont turn.


Tighten the adjusting screw with the two nuts loose but snugon the middle of the chain on the top of the bar. Tighten the chain screw until the chain is loose enough to raise the chain up about 1/2 inch then tighten the mounting nuts tight. Then see if it is ok.
Terry

Jan 07, 2015 | Husqvarna 338xpt 14" Gas Chain Saw Husky...

1 Answer

How do you fix the chain


Remove cover on the chain side of the saw. Loosen the two hex nuts that hold the bar onto the saw. You will need to loosen the tightener screw also. Place chain back onto the bar making sure the chain is positioned properly in the sprocket at the rear of the bar and just reverse the directions. Tighten the tightener screw until the chain is tightened leaving a little slack, then tighten the two hex nut. Replace the side cover. When you pull the chain down away from the bar, it should have just a bit of slack not tight. This allows the chain to turn without a lot of friction. I hope this helps.

Jan 26, 2014 | Homelite Garden

1 Answer

My throttle cable on my 1996 honda elite moped broke how could i fix it


Usually the cable breaks at the very end where the barrel is attached. if so there are cable repair barrels sold at bicycle shops that you can insert the broken cable end into and tighten a small set screw in the side to clamp down on the cable. I've had to drill the hole a little bigger for some larger cables.
Picture reference: http://t1.gstatic.com/images?q=tbn:ANd9GcTWl_KhEmoSJ8pfIqp0Dnj-_7EUayYvprBbJQF_aHC3NwBEhR2B

Dec 10, 2013 | Motorcycles

1 Answer

Tighten chain


to tighten the chain on most saws you loosen the lock nuts on the cover that goes over the clutch and on the side of the bar where the bar meets the saw you will find a screw turn the screw until it tightens while pulling down on the chain in the center of the bar until you can see the bottom of the chain

Jun 16, 2012 | Garden

1 Answer

Chain dowsn't stay tight


Between the chain bar and the body there is an adjusting screw, if the adjusting screw is stripped it will not pull on the chain bar to tighten the chain.
procedure for tightening chain. loosen the chain guard nuts, tighten the bar adjusting screw by turning to the right or clockwise, the chain has to roll freely around the bar but not bind. check with gloves or rag, don't use bare hands to avoid accidents. once chain is adjusted, tighten the chain guard nuts. good luck!

Oct 16, 2011 | Poulan Pro 42CC 2 Cycle Chainsaw, 18"

1 Answer

How do you tighten chain


Thanks for contacting FixYa. I was just reviewing some of the old unsolved problems and wanted to make sure your question gets resolved.

Chain can be correctly tightened by loosening the axle nut so the axle floats. Then tighten the chain tensioning nuts on either side evenly so they tighten the chain. When the chain is properly tensioned you will have 3/8th - 1/2" of slack between the chain and the swing arm. Then re-torque the axle nuts and lubercate the chain. Should be ready to go.

TF

Sep 13, 2010 | 2008 KTM 990 Super duke

1 Answer

How do you put a chain back onto a chainsaw


on one side of the saw are two nuts and a chain tightener screw. loosen the nuts but don't take them off. turn the tightening screw counter clockwise. the bar should slide backwards. the chain goes over the clutch disk and the tangs go into the bar groove. just keep pressing the tangs into the bar all the way to the tip and around the tip sprocket. now turn the adjustment screw clockwise which will tighten the chain. don't tighten it too much! leave a little "play" - tighten down the nuts. plug in the saw and start it. if the saw has a chain oiler press the oiler a few times. as you use the saw the chain will expand and loosen. loosen the nuts and tighten it again just a little.

Oct 25, 2009 | Electric Garden

1 Answer

Unable to tighten chain .. too droopy.


There are usually two 7/16" nuts on the side of the chain saw. Loosen those a little first, then turn the screw to tighten the chain - not too tight or you'll stretch out the chain when you use it. Don't forget to re-tighten the two nuts before using the chainsaw.


May 16, 2009 | Remington Electric Chain Saw

1 Answer

Won't start!!! (It's a moped, doesn't exist in product registry)


Remove the water trap bowl at the bottom of the petcock, (gas valve). Any water or trash in the bowl? Drain a cup of gas from the tank. Any water or trash in the cup? Dump it, clean it and re-mount it, ( not all bikes have a water trap bowl ).

Turn off the gas. Drain the carburetor> There is probably a screw on the lower side of the carb float bowl. Remove the screw then replace it after the fuel drains. Remove the carburetor from the engine.

Remove the float bowl and clean the entire carb with a spray carb cleaner from the auto parts store. Wear protective goggles to avoid getting spray in your eyes. Spray into all the little airways and fittings in the carb. Remove the two screws on the outside throat of the carb and spray into the screw holes as well.
< < READ CLOSELY > >
Be sure to put these two screws back in the same hole they came out of. IMPORTANT > do not tighten these two screws down. Only screw these in until they LIGHTLY seat. Now turn each screw one and one half turns outward. Put the rest of the carb back together, clean the air filter and install the carb. Be sure the mounting bolts are tight on the carb AND on the manifold attached to the cylinder. Tighten down the cylinder head bolts and put in a new spark plug. Turn on the gas and let the float bowl fill then start the engine. Set the idle speed with the idle screw. This process should fix the engine and probably eliminate the 'feathery' sound..


The oil leak can probably be fixed by just tightening up the case screws. The only other place for an oil leak is the shifter seal and the chain sprocket seal. Replace them if they are bad.


If the 'feathery' sound is still there then tighten down the exhaust mounting bolts. If it is still there then learn to love it....
Get a new battery Daniel, your'e hurting my head!

Please rate this solution.
( 4 diamonds would be nice ) >Thanks Daniel!

Apr 06, 2009 | 2006 Motorhispania Arena 125 Pro Racing...

Not finding what you are looking for?
2008 Derbi Senda XRace 50 SM Logo

Related Topics:

177 people viewed this question

Ask a Question

Usually answered in minutes!

Top Derbi Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Brad Brown

Level 3 Expert

18520 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

6480 Answers

Are you a Derbi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...