Question about Kymco Zing 125 Motorcycles

1 Answer

My kymco zing 125 wont start and there is oil on the spark plug when i take it out so is it the valves that are damaged or more likley the piston or rings

Posted by Anonymous on

Ad

1 Answer

madmaxx

  • Level 2:

    An expert who has achieved level 2 by getting 100 points
    MVP:

    An expert that got 5 achievements.
    New Friend:

    An expert that has 1 follower.
    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 52 Answers

The piston rings are fried

Posted on Jan 21, 2013

Ad

2 Related Answers

Edward Hurst

  • 77 Answers

SOURCE: Replace regulator/rectifier with a different brand?

Not always necessary to change the regulator/rectifier. Check all connections to make sure they are clean, use a good contact cleaner and finish off with dielectric grease on your electrical connections.
When some bikes get a few years on them the connections get dirty. Check to see if there are any burned or discolored wires anywhere around the regulator. The FIX on some bikes is to cut the connector completely out and solder the wires together and either seal them with heat shrink of a good electrical tape. Loose or bad connections get hot. As long as the regulator and rectifier are working there is no need to replace them if the connections are good.
Ride Safely, Ed

Posted on Apr 09, 2010

Ad

Anonymous

  • 1 Answer

SOURCE: wont start by kick start but will by pull start

it could be the gaskets around your carb are bad and leaking air if so its thinning your gas fumes with more air then what is needed inside your combustion chamber witch is causing your engine to stop running like that. best of luck

Posted on Apr 20, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0 Answers

2002 Kymco Hipster 125 how to remove the rusted exhaust bolts

Mar 05, 2018 | 2003 Kymco Hipster 125

0 Answers

How do I set the valve timing on a kymco zing 125 cruiser

Aug 02, 2016 | Kymco Motorcycles

0 Answers

I've a kymco zing 125cc I've had it a few weeks now and it used to drive at 70mph then over the week and lastnight it dropped again to 60mph and the bike coughs and spulters once it hits 60mph

Jul 11, 2016 | Kymco Motorcycles

0 Answers

I need a workshop manual for a kymco zing 125?

Jun 06, 2016 | Kymco Zing 125 Motorcycles

1 Answer

What is the firing order for a kymco 125cc
Its a single cylinder engine. Are you sure its not a faulty spark plug, or maybe there's no power going to the spark plug?

Nov 24, 2013 | Clear Ranger Heavy DutyTM Windshield 95-97...

1 Answer

Kymco zing what is the valve clearance
I found an owner's instruction manual on the net in Spanish that says:
0,05 mm - 0,1 mm

This means that the valve clearance is 0.05 to 0.1 mm. A slightly tight adjustment using a 0.1 feeler gage should be ok and the real clearance would then probably be ca. 0.08 mm.

Sep 30, 2011 | 2005 Kymco Zing 125

1 Answer

I recently bought a 2002 kymco zing 125 ,it has been stood for a couple of years and not started.i have replaced the coil and new battery and also the cdi unit,it has had a new spark plug too and the carb...
You should replace the fuel also as fuel deteriorates over time.Drain the tank and replace with new fuel.Also drain the carb.as it will still have old fuel in it.

Jun 18, 2011 | 2005 Kymco Zing 125

1 Answer

What is the oil capacity on a Kymco Zing 125 please.
I would put in 2 qts and then slowly add part of the third till the level comes up. No bike, not even a big one holds much more than 3 qts oil. But I'm sure you will safe at putting in 2.+. Hope this helps.

May 28, 2011 | 2005 Kymco Hipster 125

4 Answers

No power on my Kymco Zing 125
your best try is to contact your dealer, and get them to order you the short red wire that runs from the + terminal on the battery, to the starter soleniod ( also has a thin red wire that runs to fuse holder) i had exactly the same problem and this solved it. i have however re done all the electrical connections on my bike using 7amp wire and bullet connectors, as i have had many faults with the electrics before.
My bike is a Kymco Cruiser 125 (almost exactly the same bike, i use kymco zing parts when replacing) i paid approx £16 GBP for the wire.

Mar 14, 2009 | Kymco Zing 125 Motorcycles

1 Answer

Kymco Zing starting problem
the problem may be that there is not anuf power in the battery or the starter motor is on its way out

Jan 28, 2009 | 2005 Kymco Zing 125

Not finding what you are looking for?

View Most Popular

Motorcycles

Related Question

2002 Kymco Hipster 125 how to remove the rusted exhaust bolts

  • 2003 Kymco Hipster 125

Open Questions:

0 Answers

My 2019 kymco agility city 125i wont turn off when I switch it off and take out the key the engine keeps running. I have replaced the ignition switch and it still does it.

Feb 26, 2021 | Kymco Motorcycles

0 Answers

250cc. Why doesn't it start?

Jan 29, 2021 | Kymco Motorcycles

0 Answers

2009 UXV 500i. Why is there no power to the electrical system?

Apr 15, 2020 | Kymco Motorcycles

0 Answers

where can I find the key code for a 2018 Kymco Compagna? Bought used, only has 1 key. @

Sep 22, 2019 | Kymco Motorcycles

Motorcycles Logo

Related Topics:

251 people viewed this question

Ask a Question

Usually answered in minutes!

Popular Questions

Kymco Zing 125 Motorcycles

2005 Kymco Zing 125

2005 Kymco Zing 125

Kymco Zing 125 Motorcycles

2005 Kymco Zing 125

Top Kymco Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

6576 Answers

Are you a Kymco Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...