Question about 2004 Suzuki GSX-R 1000

2 Answers

I have a 2004 gxsr 1000 with fault code c42. It wont start. oil light is flashing and displays FI on the temp. Bike just crank but will not fire it up. Help?

Posted by Fernando Fonte on

Ad

2 Answers

Todd adcock

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

Vl 800 Blvd c-50. F1. Bike won't start turns over but will not engage

Posted on Jan 26, 2018

Ad

Gino Cussen

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 217 Answers

Grab a paperclip.

Place the bike in Neutral, and take the rear seat cowling off. On the side of the bike between the tail section and the trunk you will find a connector that is covered by a rubber cap, and has two wires running into it. Remove the cap and take note of which one of the 4 sockets the two wires go to. Turn the bike ON and start it up, short the wires out with the paperclip. Where your speedo was flashing a -CHEC- with the temp should now be a CXX error code. Write this code down. Then shut the bike off. Match the code up with the list below. Grab a Manual and get to work!

(What you have just done is put the bike into "Dealer Mode".

GSXR Fuel Injection (FI) Code List:

C14 - THROTTLE POSITION SENSOR
C15 - ENGINE COOLANT TEMPERATURE SENSOR
C21 - INTAKE AIR TEMPERATURE SENSOR
C22 - ATMOSPHERIC PRESSURE SENSOR
C23 - TIPOVER SENSOR
C24 - IGNITION SIGNAL #1
C25 - IGNITION SIGNAL #2
C26 - IGNITION SIGNAL #3
C27 - IGNITION SIGNAL #4
C28 - SECONDARY THROTTLE VALVE ACTUATOR
C29 - SECONDARY THROTTLE POSITION SENSOR
C30 - SECONDARY THROTTLE CONTROL UNIT
C31 - GEAR POSITION SENSOR
C32 - INJECTOR SIGNAL #1
C33 - INJECTOR SIGNAL #2
C34 - INJECTOR SIGNAL #3
C35 - INJECTOR SIGNAL #4
C41 - FUEL PUMP CONTROL SYSTEM
C42 - IGNITION SWITCH SIGNAL
C46 - EXHAUST CONTROL VALVE ACTUATOR (1000 ONLY)

03-04 GSXR1000 Workshop Manual Verify Download

Posted on Dec 27, 2014

Ad

5 Related Answers

Anonymous

  • 2336 Answers

SOURCE: Starting problem

Sounds like you might have cooked the battery. Try with a new one, start the bike and see how it runs. Hopefully you didnt fry anything else.

Posted on Nov 20, 2008

Anonymous

  • 6 Answers

SOURCE: Bike cutting off and FI light and check engine came on and off

that is the code for when a bike is laid down .... auto shut off sensor ...... as soon as u turn key off and back on it should be good to go again. ....

Posted on Jun 25, 2009

Anonymous

  • 8 Answers

SOURCE: 04-5 gsxr 1000

My 04 gsxr 1000 was parked for a year and a half when i bought it. I had a ton of rust in the fuel tank. The engine is fuel injected so it needs a free flowing fuel pump to keep a constant pressure. more than likely the strainer at the bottom of the pump housing is plugged up full of rust. You will need to remove the tank from the bike and drain all the bad fuel. Unbolt the pump housing from under the tank take care not to damage the o ring. Separate the pump from the housing by pulling apart. This may take some brute force because the rust tends to stick the pump to the housing. Once separated you will see the plastic micro strainer it will be solid brown impregnated by rust. Carefuly remove it and soak it in some fresh clean gosoline. Swish it around in a glass jar with a lid on it if possible. This worked for me. The alternative is a new strainer for about 100.00 USD. Clean the rest of the pump externally with a soft bristle brush. Drain the pump as best you can. Do not attempt to disassemble the pump as it is sealed and considered maintenance free. Ventalate the tank untill completely dry and blow it out with compressed air untill no more rust dust comes out of it. At this point you can recoat the inside of the tank if you wish, there is a product called kreme for that. Im cheap so i didn't recoat mine. Reassemble, refill with high octane fuel and dont store long term without draining the fuel tank completely and run the engine til it starves itself of fuel. With all this said YOU ARE DEALING WITH FUEL BE CAREFUL, DONT BLOW YOURSELF UP!!!

Posted on Mar 14, 2009

tombones

  • 3567 Answers

SOURCE: Max water temp and Min oil pressure GSXR 1000

I am glad you posted on FixYa. I can help on the manuals. Everything you asked for AND a parts fitch with part numbers are on the free PDF download site shown below. The 1st screen sometimes takes up to 5 seconds to build but from there the download is extremely easy.

Ya owe me a top rating on this one! Thanks Kylie!

Posted on Apr 24, 2009

Anonymous

  • 19 Answers

SOURCE: bike is cutting out and the fi light is flashing

injectors may be bad

Posted on Jul 15, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2003 Suzuki TL1000R. It was running fine, then I stopped for gas. When I tried to start it, it would only turn over slowly, but would not fire, and the little F1 light came on. Help??


Open your rear seat and you'll see a black cap covering a connector/harness on the left side of the seat. If you take the cap off, you'll see it appears to be a normal harness. With your key in the ignition and bike turned to "on" (but not running), take a paperclip and short the two connectors out (by touching the two contacts together). This is known as a "ghetto dealer mode switch". It should display the error code on your display instead of just FI now.



Fuel Injection (FI) Code List:

C14 - THROTTLE POSITION SENSOR
C15 - ENGINE COOLANT TEMPERATURE SENSOR
C21 - INTAKE AIR TEMPERATURE SENSOR
C22 - ATMOSPHERIC PRESSURE SENSOR
C23 - TIPOVER SENSOR
C24 - IGNITION SIGNAL #1
C25 - IGNITION SIGNAL #2
C26 - IGNITION SIGNAL #3
C27 - IGNITION SIGNAL #4
C28 - SECONDARY THROTTLE VALVE ACTUATOR
C29 - SECONDARY THROTTLE POSITION SENSOR
C30 - SECONDARY THROTTLE CONTROL UNIT
C31 - GEAR POSITION SENSOR
C32 - INJECTOR SIGNAL #1
C33 - INJECTOR SIGNAL #2
C34 - INJECTOR SIGNAL #3
C35 - INJECTOR SIGNAL #4
C41 - FUEL PUMP CONTROL SYSTEM
C42 - IGNITION SWITCH SIGNAL
C46 - EXHAUST CONTROL VALVE ACTUATOR (1000 ONLY)

Jul 11, 2014 | 2003 Suzuki TL 1000 R

1 Answer

Hi i have a 2004 sv1000s not getting any fire from the spark plug line i put the bike in dealer mode an i got c41 what dos that mean ?


GSXR Fuel Injection (FI) Code List:

C14 - THROTTLE POSITION SENSOR
C15 - ENGINE COOLANT TEMPERATURE SENSOR
C21 - INTAKE AIR TEMPERATURE SENSOR
C22 - ATMOSPHERIC PRESSURE SENSOR
C23 - TIPOVER SENSOR
C24 - IGNITION SIGNAL #1
C25 - IGNITION SIGNAL #2
C26 - IGNITION SIGNAL #3
C27 - IGNITION SIGNAL #4
C28 - SECONDARY THROTTLE VALVE ACTUATOR
C29 - SECONDARY THROTTLE POSITION SENSOR
C30 - SECONDARY THROTTLE CONTROL UNIT
C31 - GEAR POSITION SENSOR
C32 - INJECTOR SIGNAL #1
C33 - INJECTOR SIGNAL #2
C34 - INJECTOR SIGNAL #3
C35 - INJECTOR SIGNAL #4
C41 - FUEL PUMP CONTROL SYSTEM
C42 - IGNITION SWITCH SIGNAL
C46 - EXHAUST CONTROL VALVE ACTUATOR (1000 ONLY)

heres a list of fault codes hope it helps

John

Jan 04, 2011 | 2003 Suzuki SV 1000 S

1 Answer

I have an 02 gsxr 1000. A red warning light is coming on indicating fi,oil or coolant issues. Oil was just changed and fresh, no overheating problems. Seems to b running good. How do I figure out what's...


The lcd display should show either an oil symbol, a temp symbol, or fi to let you know which system the warning light is for. The oil symbol should be present before starting the motor and go away once the engine is running, if not you have an oil pressure problem. If it is FI, then you will need to jumper the test connector located under the seat to retrieve the codes on the display and a service manual to look up the code.

Sep 13, 2010 | 2002 Suzuki GSX-R 1000

2 Answers

F 1 appeares on dash bike turns over but wont fire


The sensors on the bike have detected a problem in the FI ( fuel Injection ) system. Take it to a dealer and they can plug in a code reader to see what is causing the problem.

Aug 03, 2010 | 1999 Suzuki TL 1000 S

1 Answer

When warming up, my K3 GSX-R1000 red light (oil) stays illuminated & F.1 displays where temp is.. what does it mean


I have been told this is the "dealer mode" and it might clear if you the bike off then turn the key back to the on position, but don't start the bike, turn it off then start the bike. this is supposed to reset the FI light.

To find out why it has brought this light up in the first place might require you actually taking it to a dealer, but there are lots of forums and info on this bike on the web

http://www.bugmanweb.com/gsxr/gsxrindex.html

Jul 12, 2009 | 2003 Suzuki GSX-R 1000

Not finding what you are looking for?
2004 Suzuki GSX-R 1000 Logo

2,162 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

6480 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

217 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...