Question about 2005 Suzuki RM-Z 250

Open Question

Kick start spring binds 2005 Suzuki RM-Z 250

Rmz kick start spring binds with the right engine cover @

Posted by Anonymous on

Ad

2 Related Answers

Anonymous

  • 12 Answers

SOURCE: rmz 250 04 model wont idal or kick start

Like I told somebody earlier to day lower the octane rating of the gas you are using....repost if you need anything futher......

Posted on Jun 22, 2009

Ad

Rinoo Kumari

  • 2973 Answers

SOURCE: my rmz 250 wont start on the first kick when the

It takes a little suction for the gas to reach the cylinder from the carb. When it is hot and on, the gas is readily available. So a kick or two, when cold starting is not abnormal. Alternatively, kick twice with the key in off position. Then turn the key on and kick, the engine will start instantly. Idea is the make the gas reach the inlet.

Posted on Feb 13, 2010

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kick start stuck


Sounds as if the starter spring on the throw out cog has slipped off to get to this you will have to remove the engine from the bike after this yon will have to take the kick starter off and remove the engine side cover you will know if this is the problem straight away as the spring will not give resistance to the side cover as it is removed at this time you will be able to check the starter cog for damage as well once side cover is removed and the starter cog is found to be good re set starter spring into the hole in the starter cog once this is completed re instale all the parts hope this has helped you good luck

May 09, 2014 | Suzuki TS 185 Motorcycles

1 Answer

Kick starter keeps binding up


do you mean it sticks down after kicking ? if so the return spring or cog on the kicker are damaged ! remove side cover and you can see the problem ! P...

Nov 22, 2013 | 2003 Yamaha YZ 250

1 Answer

Replacing kick start shaft


Great bike!

To get to the kick starter shaft and idler gear you will first have to remove the kick start and brake levers. Then remove the water pump cover and circlip, the impellor, and steel drive pin. Then remove all side cover bolts and pull the cover off the engine. Don,t let the water pump shaft come out of the engine when you pull of the cover . Suggest the best thing to do is set the engine in TDC with the timing marks on the cam side together. When the shaft come out you have to time it again, so hold it in place in the engine.

Hold WP shaft down with your thumb while pulling on the cover.

Once the cover is off the Kick Start idler gear assembly lifts out easy but as you put it together there is a center punch mark on the gear that goes in first that MUST be in aline with the spring hole drilled into the shaft, if not in aline the starter will engage at the wrong point.

Reinstall new shaft and idler gear in reverse order.




Jun 04, 2011 | 2008 KTM 250 SX-F

2 Answers

2008 rmz 250 4 stroke i was riding it and all of a sudden it cut off and now the kick start wont move but shift through gears just fine i think the top end is locked up i'm not sure could the piston of...


Remove the spark plug, put the bike in fourth or fifth gear then try a jump start but with the key turned off. If the rear wheel locks up when you jump on and release the clutch then the piston has probably seized up OR the kick start-to-clutch hub gearing is messed up. The best thing to do is to remove the left engine side cover and look at the kick start mechanism. You may need to remove the clutch assembly for a full inspection. With the clutch removed the rotor ( crankshaft flywheel ) should turn. If it will not turn then a seized piston, broken cam chain or dropped valve is likely. If the rotor does turn then the kick start mechanism is the problem. Please rate my answer. Thanks!

Mar 26, 2011 | 2004 Suzuki RM-Z 250

2 Answers

Are there timing issues with the 2006 rmz 450? I replaced the valves, (bent from timing) cam timing chain, oil and oil filiter. When I try to start it it backfires but will start... Once it gets hot and...


have u tried turning the engine over slow for about three to four turns with the kick starter then kick it once or twice hard ..it should start...dont give it any throttle...floods easy

Oct 09, 2010 | 2005 Suzuki RM-Z 450

1 Answer

I have a kawasakikmx 125 which had a slipping kick start i have removed the engine casing but cannot see where the spring end is meant to locate does anyone have a diagram please thanks Neil


I can't find a diagram of the position of the spring when connected, but I can describe it, the spring has 1 straight end that connects through in the hole in the shaft of the kick start, and a bent one protruding out of the bottom of the spring at a kind of right angle. This one goes into the casing of the engine not the case cover, if you look around the edge of the casing, just below where the kick start assembly goes you should see a hole that holds no purpose. That where the other end of the spring goes, just pop it in and lever the assembly back to position.

May 15, 2010 | 2002 kawasaki KMX 125

1 Answer

My rmz 250 wont start on the first kick when the choke is on but when the engine is on and hot it starts first kick with no choke?????????


It takes a little suction for the gas to reach the cylinder from the carb. When it is hot and on, the gas is readily available. So a kick or two, when cold starting is not abnormal. Alternatively, kick twice with the key in off position. Then turn the key on and kick, the engine will start instantly. Idea is the make the gas reach the inlet.

Feb 13, 2010 | 2004 Suzuki RM-Z 250

2 Answers

My drz 110 makes a ratcheting sound and wont turn over


the main shaft has broken and possibly the first gear and right engine case. Common problem.

Jan 06, 2010 | 2005 kawasaki KLX 110

1 Answer

Having problems changing gears,gear lever not springing to central point to up or down change,b king less than year old,sounds like internal selection fault,any ideas?


drain engine oil.pull right side (clutch) cover off. check shift shaft to see what is making it bind. check shift drum detent arm to see if it is engaging shift drum correctly.check if shift shaft is binding in the engine cases, may be bent. when you pull the cover you will need to scrape the old gasket off & replace, also engine oil & filter.

Feb 20, 2009 | 2008 Suzuki B-king

Not finding what you are looking for?
2005 Suzuki RM-Z 250 Logo

Related Topics:

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

6495 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

217 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...