Question about Motorcycles

1 Answer

Honda cbr1000f front end wobble with clunking noise

I have a front end wobble with a clunking noise,i have checked the bearings and they seem to be ok

Posted by tony watkins on

Ad

1 Answer

Bobby Blevins

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 229 Answers

Have you checked the neck bearings? The brake calipers? and the pads?

Posted on Sep 24, 2012

Ad

5 Related Answers

Anonymous

  • 1 Answer

SOURCE: front end wobble

the problem is the fall away is out of adjustment i had the same problem take it to harley dealer to have it adjusted

Posted on Mar 16, 2009

Ad

Tom Diffin

  • 95 Answers

SOURCE: frount end woddle/weave springer 30 - 40

check the wheel alignment front and rear a little out of alignment and a lot of wobble

Posted on Dec 31, 2008

Anonymous

  • 2 Answers

SOURCE: front end wobbles

yoik head bearings (stering head bearings)

Posted on Apr 03, 2009

ROB

  • 858 Answers

SOURCE: problem with a wobble from front end of my pan

check the wheel bearings then the rim for runout when its spun !
Cheers Rob

Posted on Aug 15, 2009

miket756

Michael Thorpe

  • 2702 Answers

SOURCE: gs750 1978 front end juddering

most tyres would have a weight on the rims if they were balanced its very rear they dont, but check the head bearings first,,,but my money is on that new tyer being out of balance

Posted on Mar 14, 2010

Testimonial: "Appreciate the advice.Thanks."

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Idle on my 1983 honda goldwing goes up and down and flucuates very bad.


clean the fuel system , carbs etc ! check your wheel bearings , headstock bearings and clamps are tight , tyre walls are ok and tyre pressure ok , i once used a metzler me33 and it was all over the place , bin'd it even though it was new as it nearly killed me ! put a bridgestone on and was perfect ! check your fork oil is good and correct level etc , fork springs are ok and same length and air pressure even ! frame clamps tight , no cracks etc !

Apr 11, 2014 | 1983 Honda GL 1100 Innerstate Gold Wing

1 Answer

Front end vibration


check you springs you may have a broken spring also jack the wheel up one at a time and check the bearing hands 9 and 3 pull side to side and then up and down at 12 to 6 any excessive movement and the bearing needs changing. do this to both wheels. also check the anti roll bar rubbers all 4 of them check for splits or wear this can also make a clunking sound on bumps of any size. failing all these you may need to have your disc's checked as they may have become warped can happen if you use them alot ie hills, sudden stopping

Jan 15, 2014 | Ford Taurus Cars & Trucks

1 Answer

Ge adora WHDVH626FWW makes clunking noises when spinning, bearings seem ok


Could be a broken Hub Spoke, My Kenmore broke at the spokesand bearing e.of drum,
Sears replaced all parts as the were still uder warrenty. Less than 10 years old, would have been over $1,000 cost otherwis.

Sep 30, 2012 | GE Wh12x10309 Heater for Adora Front Load...

2 Answers

Can bad axel cause front end shake


yes. if the axle is bad and binding it can cause the front end to vibrate because it gets out of balance.

Aug 05, 2011 | Buick LeSabre Cars & Trucks

1 Answer

My van seems to be wobbly and kinds a knocking noise in he front end.


You need to have that checked very soon. Could be a wheel bearing or cv joint going out and could be dangerous. I lean toward the wheel bearing.

Jun 08, 2010 | 1999 Chevrolet Venture

1 Answer

Problem with a wobble from front end of my pan european tyre seems ok and inflation is ok


check the wheel bearings then the rim for runout when its spun !
Cheers Rob

Aug 15, 2009 | 1990 Honda ST 1100 Pan European

2 Answers

Front end wobbles


yoik head bearings (stering head bearings)

Apr 03, 2009 | 1995 Honda CBR 1000 F

1 Answer

Clunking/vibration/squeling noise under the front end


sounds like u need front brake pads and rotors i would check brakes first if ok then i would check front wheel bearings but cv joints make a clicking sound usauly when turning

Mar 29, 2009 | 1997 Chevrolet Cavalier

1 Answer

Frount end woddle/weave springer 30 - 40


check the wheel alignment front and rear a little out of alignment and a lot of wobble

Dec 27, 2008 | 2000 Harley Davidson FLSTS Heritage...

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

295 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

6523 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Brad Brown

Level 3 Expert

18563 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...