Question about 1993 Yamaha XV 535 Virago DX

Open Question

Eletrical faults tail lights dip dull when u use the dip switch on the front handle bars

Posted by sarahjane on

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

One headlight stays on after turning car off.


with engine on, check lights, main beam and dip and side lights. Check tail lights work too.
With lights on, turn the indicator switch left for a few seconds then right. You are looking for odd behavior with lights.
It's a good indication of an earthing fault (grounding).
Turn engine off and see if lights-on warning alarm sounds.
Corrosion around connectors often causes light faults, check them all, if they seem sound then check the relays.
Another possibility is the switch itself. Wiggle it around very gently feeling for loose movement or flickering lights. The whole switch may need replacing. It's a start......after that then you need to check wiring loom. (very rarely the bulb is the fault so test them with a circuit tester)

Jan 29, 2017 | Cars & Trucks

1 Answer

Harley Davinson 1986 break light wont turn off


One of the switches, on the handle bar, or foot pedal is closed all the time. Disconnect one at a time and determine which one it is. It may just need an adjustment to keep it from completing the circuit. If not, replace the switch. Sometimes the brake filiment (inside the bulb) will break and fall over onto the tail-light filiment. This will cause the tail-light to light brightly, as if the brake switch is closed in. Try a bulb first.

Jun 27, 2013 | Motorcycles

1 Answer

Tail light not coming on put a stock one in


Mine acted up this year also. I sprayed WD-40 in my ignition switch slot and the lights started working. Then later my left front running light would not stay on. I had to constantly adjust the turn switch while riding to get it to stay on. I got home sprayed WD-40 into the switch lever on the handle bar. Swapped back and forth from left to right with the turn signals. Worked from then on. Go WD-40!! Cheap and worth a shot.

Apr 04, 2013 | Honda Motorcycles

1 Answer

Tail light wont go when using front break on 2005 Ducati Multistrada 620


Please check your switch using a volt/ohm meter to assure it IS working and not just clicking.

Feb 09, 2013 | 2005 Ducati Multistrada 620

1 Answer

No brake light looking for a wire diagram to trace the problem. checked bulb its good, fuse?, not sure where to look?


Have you been working on handle bars like putting on new grips there is a switch on front brake it migt be out of adjustment Look to see if both elements are lite on tail light MOPAR KENNY Hope i could help

May 22, 2011 | Harley Davidson FXDWG Dyna Wide Glide...

1 Answer

You turn the handle bars to the left the head lights turn off


Sounds like you have a short. The headlight and the tail light are on the same fuse as well as a few other lights. I'd look closely right where the main harness goes from the frame to the front end. There is a lot of flexing and movement in the wiring harness in that area. Look for wires that could have been rubbed by the fairing.

Good Luck
steve

Jul 20, 2010 | 2003 Harley Davidson FLHTCUI Electra Glide...

1 Answer

Yamaha r6 braking lights


Start with a new brake\tail bulb, then try unplugging the front brake switch on the handle bars , then try unplugging the rear brake switch. one of these options should locate a problem

Apr 22, 2010 | 2005 Yamaha YZF-R6

1 Answer

1988 Kawasaki 250 El Eletrical


You might try to check the horn first by shortcircuiting it ( two leads from the battery.) If the horn itself works , find your way up: check with your contact switched on, the wires that lead to the horn by using a small light bulb or an Voltmeter: if you push the horn button, the licht should go on or the voltmeter should read 12 v.. If not , check the horn switch itself, there could be some corrosion. Good luck , allways a puzzle , the electricity..

Apr 02, 2010 | 1988 kawasaki ZL 250 Eliminator

2 Answers

Brake lighht does not work from front or rear lever, bulbs are fine.


Please check both switches - one on the handle bar and the other on the foot petal.

To prove or disprove, unplug then and short them out. If you short the harness out and the light llights, replace the switch.

You can also check the fuse in the fuse box ...

Thanks for posting your question on FixYa.com

please vote

thank you

a

Nov 11, 2009 | 1984 Yamaha FJ 1100

1 Answer

Grab handles


oggi knobs. anodised barends, heli bars. arrow cans, custom rear peg mounts, white power shock, hugger, undertail, clear tail light lens, PC 11 , modded airbox, K&N air filter, 6 spots, braided front lines, polished rims and colour matched painted wheel spokes, fan override switch , TRE, tank bra, american high capacity battery, sv650 grab rail,RGV250 front guard.

Nov 20, 2008 | 2002 Suzuki TL 1000 R

Not finding what you are looking for?
1993 Yamaha XV 535 Virago DX Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

gbob59

Level 3 Expert

3063 Answers

randymanfive

Level 3 Expert

501 Answers

Cindy Wells

Level 3 Expert

6220 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...