Question about Piaggio Motorcycles

Open Question

Rear brake light not working 2002 Vespa PX 125

Vespa px 125 02plate back brake light not working when pressing foot pedal Brake light did flash on then off a couple of times but I needed to push the foot pedal fairly hard and now not working at all @

Posted by richy garvock on

Ad

5 Related Answers

Anonymous

  • 948 Answers

SOURCE: Brake pedal won't return.

There could be a couple reasons for this. First thing to check is your return spring, is it still there and attached properly? Next thing to check is your master cylinder pressure release. Loosen the bleed nipple on the rear caliper. Does the brake release now? If so, your master cylinder has some debris clogging the fluid return passageway. Remove and clean it. If the brake still does not release after opening the bleed nipple, at least one of your caliper pistons is binding. Remove the rear caliper and the brake pads. Now press the pedal and force the pistons out. Looses the bleed nipple and attempt to press the pistons back into place. They should move smoothly when you apply firm pressure. Clean the caliper thoroughly. If you have a rebuild kit for the caliper this is a good time to rebuild it. After cleaning, put it back together, bleed the brakes and test again. It is normal for disk brakes to drag SLIGHTLY on the rotor, but they should not stop a free spinning wheel in less than a coupld revolutions when spun by hand.

Posted on Feb 15, 2009

Ad

Anonymous

  • 11 Answers

SOURCE: Suzuki VL intruder 125 back brake sticking and braklight stuck on

i too had this problem .....dnt worry just remove the brake cable and lubricate it with some spray like ABRO or WD40 lubricating spray then you sprayed some in the cable.play with it pull it forward and push it backward.,lubricate and repeat the steps till you find the cable goes smoother...you know it usually happens due to dust and dirt which enters the cable n get it stuck,try this n tell me..

Posted on Mar 27, 2009

Ad

Anonymous

  • 3 Answers

SOURCE: CANT GET FRONT LIGHT AND INDERCATORS WORKING BACK LIGHTS ALL WORK OK

check fuses and then retrace each indicator conector wire back to the fuse . Once this is done check the fuse to power line if it is a factory problem then they should be able to fix the problem directlly and frre of charge regardless if you brought the bike new or used it is there responsibilty.

Posted on May 06, 2009

Anonymous

  • 435 Answers

SOURCE: kawasaki kx85 04 rear brake not working

Depending upon the braking system,you need to service it accordingly.I assume it is 85cc engine and it will have a drum disk.You need to remove the tyre and check the pads,if the pads are fine then give it a good high pressure air to blow away all the dust inside.Then put back things tohether and adjust brake to stop the pedal from going too much down accordingly.Make sure all bolts are secured,align wheel and check chain tension when assembling.Hope this help.

Posted on Aug 23, 2009

maaaartin

  • 561 Answers

SOURCE: vespa px lights do not work

check the connection of the bulb ensure itis fitted correctly also check fuses it maybe that the bulb for the lights has blown, it is common that the brake light is on a seperate fuse for safety.

Posted on Dec 02, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When applying the brakes on my vespa px the lights go out and the rear brake light doesn't work


That would indicate that you have a short to ground in the circuit, so that when you apply the brakes, you ground the system and the lights cut off. Check all of the wiring carefully, especially at the brake lever and make sure that when you move the lever, no wires are caught or moving.

Mar 07, 2015 | Vespa Motorcycles

1 Answer

What will make the brake light not work from the foot pedal but does work from the hand lever and the back running lights don't work but the turn signals do on a 2006 1200 sportster


Most cars have a switch mounted to the brake pedal assembly and when you press the brake pedal down it pushes on the switch and completes the circuit for the brake lights. The parking brake has a different switch and circuit. Get a Haynes manual for your car it should have the location of the brake switch and how to test it. Good luck

May 12, 2014 | Cars & Trucks

1 Answer

How do i replace brake pads on vespa px 125


if you have experience as a mechanic you can do it by yourself, but otherwise it is better to have it done by a pro, as the brakes are a main safety item....
How to replace Vespa drum brakes NYC Scootering New York City scooter news...
replace-brake-pads-vespa-px-125-hrvlixid2vnvvtoada3i3rpn-5-0.jpg replace-brake-pads-vespa-px-125-hrvlixid2vnvvtoada3i3rpn-5-2.jpg replace-brake-pads-vespa-px-125-hrvlixid2vnvvtoada3i3rpn-5-5.jpg

Feb 23, 2012 | 2011 Vespa PX 125

2 Answers

Hi: I have a 1998 Chevy Blazer 4.3 The brake lights and turn signals don't work.... HELP


Sounds like you have a bad multiple function turn signal switch. A couple things to try With your foot pressing on the brake pedal, Press the four way flasher button up and down, press and hold it down, pull up on it, or wiggle it. If the brake lights come on during any one of those replace the switch. With the key in the run position pull, push, the turn signal lever slightly. If the turn signal or brake lights start to work replace the switch. Let me know if none of those work, they usually do, and I'll get you some more in depth diagnostic info.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Jun 17, 2011 | 1998 Chevrolet Blazer

1 Answer

Brake light stays on with beeping sound


Check & replace if necessary the brake pedal switch placed above pedals on the support.

The brake pedal switch on a 2001 VW Beetle is placed above pedals on the support.

1. Remove the cover panel above the driver's side foot well...

tdisline_603.jpg


2. Locate old switch, push in brake pedal, and twist switch body to remove...

tdisline_604.jpg
3. Unplug 4 pin connector from old switch and plug into new switch (it only goes one way...don't force it!). Insert new switch into frame and depress brake petal. You should turn it until it locks into place and is positioned like the original.
tdisline_605.jpg
4. Start Bug. Press the brake pedal once or twice and the EPC light should go out ...

tdisline_606.jpg
5. If it looks like that... great! Replace the cover over the foot well and you are done! If not, check the 4 pin connection and make sure it is fully seated in the switch. Also check to see if you can hear the switch engage when you press the brake pedal ... if not, you will need to remove the switch and adjust the push rod. The rod will move in and out for adjustment. Check to see if the brake lights come on when you press the brake pedal as well!
tdisline_607.jpg

Jun 01, 2011 | 2001 Volkswagen Beetle

2 Answers

Why wont my brake light turn off... they are on all the time


You most likely have a faulty stop light switch. I have provided you with a couple of pictures. The first one in black and white is where you will find the switch and the second one is a picture of what your switch should look like but may not be what is in the car but you will get the idea. What happens is when you press the brake pedal a little button on the switch opens and when it opens it completes an electrical circuit and turns the brake lights on. when you let off the brake pedal the pedal comes back up and pushes that button back in to close the circuit. it is most likeley stuck open and not pushing back in when the pedal goes back up. When you see it you will understand better. I hope this helps you and good luck.


clifford224_136.jpgclifford224_137.jpg

Mar 12, 2011 | 2001 Ford Taurus

1 Answer

Brake lights come on and stay on when started.Recently replaced left brake light bulb


It sounds like the brake switch on the brake pedal arm is stuck its like a push button type switch when you press the brake pedal down it pushes the button in on the switch which makes the brake lights come on,when you take your foot off the brake pedal the button is supposed to come back out if it doesn't the brake lights will stay on.

Apr 09, 2010 | 2002 Audi A4

1 Answer

Vespa px lights do not work


check the connection of the bulb ensure itis fitted correctly also check fuses it maybe that the bulb for the lights has blown, it is common that the brake light is on a seperate fuse for safety.

Dec 02, 2009 | Peg Perego Vespa Scooter

1 Answer

Electric start on vespa px does not work


Could be a deficient battery, malfunctioning solenoid, starter is burnt, starter switch, or brake light switch, as these are necessary. If your brake light is not working, that's it. I need more information.

Nov 29, 2009 | Peg Perego Vespa Scooter

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

554 views

Ask a Question

Usually answered in minutes!

Top Piaggio Experts

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

6613 Answers

ADMIN Canada
ADMIN Canada

Level 3 Expert

37420 Answers

Are you a Piaggio Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...