Question about 2010 Eton Sport 50

1 Answer

No spark on 2010 Eton Sport 50

Does the black and yellow wire CID supply power to the coil? @

Posted by on

  • Bob Hunt Jul 24, 2012

    does the black and yellow wire from the CID supply power to the coil? There is power on the other 3 at the CID.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    One Above All:

    The expert with highest point at the last day of the past 12 weeks.

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

  • Eton Master
  • 59,350 Answers

Hi, Bob and the usual suspects are:
1. Fouled spark plugs.
2. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead-acid batteries.
3. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Loose connection at ignition coil or plug between ignition sensor and module.
5. Spark plug cables in bad condition, shorting/leaking, spark plug cable connections loose check for spark leakage in the dark.
6. A faulty ignition coil or electronic control module.
7. Faulty pulse coil.
8. Faulty CKP, CMP, or BAS sensor.
9. Faulty ignition switch.
10. Faulty run/off switch
11. Tilt sensor needs a reset.
12. Security alarm failing to disarm needs reset
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.youtube.com/watch?v=HpN2YGhVGtI
https://www.youtube.com/watch?v=UU4S0Ov9q4c
https://www.manualslib.com/manual/911747/E-Ton-Sport-50.html
https://alpha-sports.com/eton_parts.htm
https://www.manualslib.com/manual/881852/E-Ton-Sport-50-Av05w9-A.html

Posted on Nov 09, 2019

Ad

3 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Gowtham

  • 31 Answers

SOURCE: how do i fix my gas needle on an eton sport 50 scooter

  • 1

    Unfasten the kickstart by loosening the bolt head of the pin that attaches the kickstart to the outside of your scooter's variator case. This will allow you to pull the pin and remove the kickstart.

  • 2

    Remove the outer face of the variator system. On most scooters, this faceplate is attached to the variator case with six bolts.



  • Posted on Nov 01, 2012

    gregg201

    Gregg Mahin

    • 59350 Answers

    SOURCE: Eton Viper 90 wiring diagram

    Hi, Bruce for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one.
    For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
    Eton Viper 90 wiring diagram Google Search
    https://get2itparts.com/etontech/WD_R90.pdf
    ETON ATV RXL 50 Service Manual
    http://www.alpha-sports.com/eton_parts.htm
    http://www.etonamerica.com/PDF/OM/OM_RXL507090.pdf

    Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

    Posted on Jan 12, 2018

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    Hi I have a Suzuki DT 16 engine 1602 no 207668 I have no spark at the plugs I have put a volt test on the green going into the CDI unit about 3 to 4 volts when pulled what should it be Thanks Mike


    With or without remote control??
    Disconnect the black/red wire from the CDI, if you have sparks, kill circuit shorted.
    No spark: check coils
    1 . The two pulser coils are located at 1 80°angles to each other and the
    condenser and battery charge coils are also located opposite of each other
    under the flywheel.
    2. Remove the engine cover.
    3. On models equipped with electric starters, disconnect the negative
    battery cable.
    4. Disconnect the connector and black ground wire.
    5. On the No. 1 pulser coil, connect the digital multi meter between the
    black/red wire terminal in the connector and the black ground wire. And the
    No.2 coil between the white/green wire terminal in the connector and the
    black ground wire. Resistance should be 260-380 ohms.
    6. On the condenser charge coil, measure the resistance between the
    black/red and green wires. Resistance should be between 1 70-250 ohms.
    7. If the resistance reading is not within specification, replace the faulty
    coil.
    8. On the battery charge coil, measure the resistance between the
    yellow/red and yellow wires, red and yellow wires (DT1 5MC) or the red and
    yellow wires (DT15CE). Resistance should measure between 0.2 and 0.5
    ohms.
    9. If the resistance reading is not within specification, replace the faulty
    coil.

    Jul 26, 2017 | Clymer Suzuki 2-225 HP Outboards Includes...

    1 Answer

    2001rfz4 e-ton 50 rascal has no spark checked all the wiring


    does the coil give power to distributor cap? check this. In order to trace fault you shuld be be working backwards from the plugs toward the battery, eventually you will find some if the battery is live and properly connected. When you do find power the fault is between that point and the one prior to it.Pretty straight forward really

    Jun 05, 2015 | Cars & Trucks

    1 Answer

    Does it matter how the coils are wired? Also, I didn't have a red/yellow wire to connect to a coil.


    Hi Allen it does matter usually the coil wires have two wires one black and red/white on one coil and black and red/yellow. The two blacks are for power so find which wires on your bile are live and put them to the black wires it don't matter which side. The other wires are for the pick up. Or points depending on the bike. These need to go to the correct coil. When it's all connected stick a plug in one of the caps and let it rest on top of the cyl head and turn the motor over if its all good you will see a spark. Regards Jim...

    May 27, 2015 | Motorcycles

    1 Answer

    No spark from ignition coil


    No vehicle shown here

    Can you not find how to test your
    ignition system on the internet ?

    I have no problems finding anything on
    any subject

    Aug 11, 2014 | Cars & Trucks

    1 Answer

    I have a 92 Honda accord wagon does not get power to coil. Distritutor Or fuel pump. Coil and distributor are both new. Any idea what it could be Thanks Rob


    Check your maxi fuses in the under hood fuse/relay box. The black/yellow wire to the coil is directly from the ignition switch-it should be hot in run.
    Fuse # 15 is an 80 amp fuse, and fuse #19 is a 50 amp fuse. Both of these supply the ignition switch with power.

    May 12, 2014 | Cars & Trucks

    1 Answer

    Dash door and brake warning lights on; car won'tstart; seems like no gass.


    There is an ECM to control the starting and running of the engine but it seldom is the problem.

    First you need to isolate if it is mechanical, electrical or fuel that is causing the problem.

    Remove the distributor cap and crank the engine, if the rotor turns, we can skip mechanical.

    Before checking any electricals, check if there are any blown fuses both under dash and hood.

    Check for power supply to distributor Black/Yellow wire with ignition switch on. If there is, pull 1 plug wire out and insert a plug to its end and ground it on the engine, NEVER groud it to the battery terminals.

    Crank the engine and if you see blue sparks it is ok, reddish or yellow sparks means the coils is bad.

    If no sparks, the ICM is faulty.

    Test for power supply to fuel pump at initial ignition switch turned on, (2 seconds only) and while cranking. If none, the main relay is faulty.


    Take care

    Oct 09, 2010 | 1999 Honda Accord

    1 Answer

    With the ign. sw in the on position should i have voltage on yellow wire ging to coil


    The ignition switch on a chainsaw operates on a ground. When the switch is "on" the coil is not grounded out, and the magneto can supply power to the coil. When it is "off" the coil is grounded, and no power gets to the coil. If you are checking for spark you can bypass the switch by removing the wire to the coil. It may just be a bad switch. A two stroke motor uses magnets to power the coil through the magneto. If the switch is grounding out there may be no spark!

    Aug 21, 2010 | Garden

    1 Answer

    Hi, I have a 1998 cbr 600f3. There are 2 coils on this bike for 4 cylinders and two wires coming in and 2 coming out(spark plug wires going out). I can only get one side of both coils to fire so the bike...


    Hi and welcome to FixYa,

    On the 2 ignition coils:
    • two wires coming in - black/white carries/supplies IGN + 12 to both coils and the ignition control module. Coil1 (left) is connected to the ICM by the yellow/blue wire while coil2 (right) is connected through the blue/yellow wire;
    • 2 coming out - left coil powers 1 & 4 while right coil powers 2 & 3;
    • 1 &4 will fire together; so with 2 &3.

    Good luck and thank you for asking FixYa.

    Nov 11, 2009 | Honda CBR 600 F(3)T Motorcycles

    1 Answer

    2005 yamaha royal star venture. Still haven't found the problem with no spark on left rear coil. I replaced the coil, but there still isn't any spark. The wires (orange and black/red have continuity to the...


    If you have continuity from the coil to the ignitor, the problem lies within the ignitor. The coils function by having a constant battery voltage on the red/black wire (you'll notice that ALL the coils have a red/black wire) - the primary windings in the coil charge up, until the ignitor "grounds" the colored wire (grey and white in the front, orange and yellow in the rear). As the voltage in the primary winding drops, it creates a strong magnetic field - the magnet (laminated iron) in the center of the coil charges the secondary windings, and the very high voltages generated fire the plug. You've already determined that the voltage on the orange wire is higher than the voltage on the yellow wire; that could only be because the orange wire is not being "grounded" on a recurring basis by the ignitor. (You have to remember that the meter you're testing the leads with cannot react to changes in voltage nearly as quickly as they happen; to really "see" what's happening at the coil, you'd need to use an oscilloscope).

    Aug 25, 2009 | 2005 Yamaha Royal Star Venture

    Not finding what you are looking for?
    2010 Eton Sport 50 Logo

    Related Topics:

    254 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Eton Experts

    Vincent G
    Vincent G

    Level 3 Expert

    2361 Answers

    Vernon Taylor

    Level 3 Expert

    5907 Answers

    Brad Brown

    Level 3 Expert

    18110 Answers

    Are you an Eton Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...