Question about Motorcycles

1 Answer

My 150cc scooter turned off while running

I was on my way home from work and was doing about 40kpm and my scooter turned off and wouldnt turn back on .i did notice a bit of smoke comming out of the belt housing can you please help

Posted by edwinalberto on

Ad

1 Answer

antonio andino

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have a 150 sunl scooter when is cold the bike work but when is hot it starts to smoke and then when i give gas it shut of but it stay on running it only shut of when i give gas need some help

Posted on Oct 21, 2013

Ad

5 Related Answers

Anonymous

  • 99 Answers

SOURCE: i have a 2007 keeway arn 150cc scooter i got alot

first of all, was the bike running, then parked for a signifigant period of time? if so, the first thing your going to want to check is the fuel system. theres a fuel hose running from the fuel tank to the carburetor. remove the fuel line from the carb to check the condition of the fuel. fresh gas has almost a clear look. if it appears to be fine, then proceed by checking the carb to see if there is fuel in the reservoir. at the bottom of the carburetor, there should be a small screw. turn it out counterclockwise to see if gas comes out from one of the overflow fittings on the carb. if it begins to leak, then you most likely have enough fuel in the carb to start it. if it comes out of the hose looking dark, or smelling kind of funny, then youll need to clean the fuel system. to do that, you must drain all of the old fuel, flush the fuel tank a bit with fresh fuel, refill it with fresh fuel, and also clean out the carburetor. if youve never done this before, i would reccommend having a technician do it for you. lost parts or mis-adjusted carburetors can not only cause mechanical damage, but also be a potential safety hazzard due to performance problems. if the fuel looks and smells fresh, then your going to want to check for ignition next. remove the spark plug from the cylinder head, attatch the boot to the top of the plug, make sure the electrode end is touching a good grounding point on the engine, and press the start button. BE CAREFUL on this step. if the plug sint grounded well, it could lead to you getting an electrical shock from the ignition system. its a good idea to hold the spark plug or boot with insulated pliers during this step, just as a precaution. while the engine is turning over, watch the gap on the spark plug end to see if there is a noticable spark. it should be fairly easy to hear as well. if there is spark, then your ignition system is most likely in good condition, so move on to the next step. if there is no spark, try this process over with a new spark plug. if the new one still doesnt spark, there is a problem with one of the components in the electrical system, and that should be further diagnosed by a certified technician.
I hope this helps you out a little bit. these are the first things that I would check. If you know the fuel system is in good condition, and you can see that there is a good ignition source, then you have a mechanical problem that would require more information to attemp to diagnose. if you have any questions, feel free to contact me. Ill be happy to further clarify or explain anything that I mentioned here.

Posted on Jul 28, 2009

Ad

tombones

  • 3567 Answers

SOURCE: I have a Roketa 150cc Sicily Scooter (2006). It

Here's the deal. I have never even heard of your bike brand but I have 18 years in bike repair. If you promise not to give me anything less than a "helpful" rating I will tell you how to do the fix based on the assumption that the bike has a standard carb and not a CV carb. The standard carb has a top "cap" that unscrews from the center of the carb body.
.
ALWAYS have a fire extinguisher on hand when working on carburetors.
Remove the water trap bowl at the bottom of the petcock, (gas valve). Is there any water or trash in the bowl? Drain a cup of gas from the tank. Is there any water or trash in the cup? Dump it, clean it and re-mount it, ( not all bikes have a water trap bowl ).

Drain the carburetor. There should be a screw on the lower side or bottom of the carb float bowl. Remove the screw then replace it after the fuel drains. Turn the gas back on and wait a minute for the carb to fill with gas. If the bike doesn't start and run properly then shut off the gas and remove the carburetor from the engine. Now unscrew the top cap and pull the slide out of the throat of the carb. When you re-install the slide, be sure the long notch on the side of the slide lines up with the small pin inside the throat of the carb.

Remove the float bowl and clean the entire carb with a spray carb cleaner from the auto parts store. Wear protective goggles to avoid getting spray in your eyes. Spray into all the little airways and fittings in the carb. Remove the idle screw and the air screw on the outside throat of the
carb and spray into the screw holes as well.
< < READ CLOSELY > >
Be sure to put these two screws back in the same hole they came out of. IMPORTANT > do not tighten these two adjusters down. Only screw these in until they LIGHTLY seat. Now turn each adjuster one and one half turns outward. Before putting the slide back in the throat of the carb, move the clip on the jet needle one notch lower. Put the rest of the
carb back together, clean the air filter and install the carb. Let the float bowl fill then start the engine. This process should get you back on the road.

Please rate this solution. Thanks!

Posted on Jun 09, 2009

Anonymous

  • 1 Answer

SOURCE: I have a 150cc jonway scooter. When I open it up

I found that if I run 87 octane gasoline the engine accelerates up to full speed without the skipping and bogging down at any point it is running. It is worth trying. also try putting some "Sta-bil" fuel stabilizer in the gasoline - it has the ability to keep the carbureator cleaner. Not just during the time you are storing it, but rather all the time.

Posted on Jun 03, 2009

Benimur

Louie Role

  • 6966 Answers

SOURCE: 150CC Roketa Scooter

Hi and welcome to FixYa,

On most versions of Roketa 150cc engines, the choke is automatic and electrically driven..  It is integrated with the carburetor.

Good luck and thank you for asking FixYa.

Posted on Jun 29, 2009

Anonymous

  • 4 Answers

SOURCE: Where can I get an electrical schematic for a

check out go scoot .com very large in china made scooter/atv/dirt bikes

Posted on Sep 12, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cant put into gear. Errors anti pollution sytem failure. Low oil pressure


change mechanics --or bring back and have them fix correctly when they did the engine work doesnt sound like was done correctly and now you may have a bigger problem

Aug 08, 2016 | 2007 Peugeot 207 CC

1 Answer

My city bug scooter just beeps when I turn it on. I just put in a new battery. It worked for a bit. Now it just beeps. I do not have a button on the bottom to push. Help....


scooter from the front and it should be on the underside of the scooter , or the main fuse might be blown....
http://www.kymco.com/upload/CTContent/6/644A6FCF-D327-4F9A-8A2D-67168B67ECE6/AGILITY_CITY%2050%20125.pdf

May 12, 2014 | TitanNet PowerStar Replacement battery for...

1 Answer

Smoking from under hood


A leak of some fluid, probably oil, dripping onto the exhaust. This smells terrible, and it only needs a drop or two.

Jan 22, 2014 | Honda Cars & Trucks

1 Answer

I just bought a 1996 Volkswagen limited edition. Its an okay car. I've only ever owned Hondas. So I don't know much about this car. It has a 154k miles. I have had it for 3 days. the only thing I noticed...


might just need the belt tightening a bit also on top of the suspension legs their is a plastic cover (optional as they gat lost) well put some engine oil in this top bearing ,yes i know you cannot see it only a big nut but some engine oil around this nut so it stays in teh recess and after a few days it will work its way into the top bearing which will lubricate it as these top bearings can and do go dry causing hard steerring .these cars are legendayr for no problems especially the diesel manual version which is highly sought after by the local arab population

Feb 13, 2011 | 1996 Volkswagen Jetta

1 Answer

Scooter wont start


carb could be clogged with trash even though fuel is gettin to carb the main jet could be blocked not letting fuel enter intake

Aug 02, 2009 | 2004 Sym Husky 125

1 Answer

Wiring problem, puff of smoke came from hazard button


I have got the smoke *** well from hazard button. The fog lights switch was melt.

May 26, 2009 | 2005 Chrysler PT Cruiser

3 Answers

2 stroke engine smokes. how do you adjust the fuel/oil mixture?


The thing with two strokes is that they smoke a bit under normal operation, and they smoke like mad if they haven't really been run for a period of time, I would advise you to run it for a while and see if that helps.

You should not need to adjust the mixture settings at all.


Hope this helps

Feb 07, 2009 | 2008 Keeway Matrix 150

1 Answer

My wifes strider chair runs a bit the stops. Then she turns off the key, turns it back on and it runs a little bit a stops. The green light stays steady until it stops then blinks..any help?


Ztarg is the Medline Industries approved service and parts distributor for the Strider and Gemini Scooters. 

Their contact information can be found on their website www.striderscooterservice.com 

Dec 15, 2008 | Electric Strider Midi 4 Wheel Mobility...

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

253 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

6480 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...