Question about 2008 Yamaha Raider

1 Answer

Replace throttle cable on a Yamaha Raider - 2008 Yamaha Raider

Posted by Anonymous on

Ad

1 Answer

Gregg Mahin

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    One Above All:

    The expert with highest point at the last day of the past 12 weeks.

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

  • Yamaha Master
  • 65,053 Answers

Hi, Anonymous for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Throttle Cables
Changing Motorcycle Lines Cables Video Guide Tip of the Week
Yamaha XV19SW Service Manual
OEM parts for Yamaha
Yamaha ROADLINER XV19SW Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Posted on May 05, 2017

Ad

3 Related Answers

Anonymous

  • 115 Answers

SOURCE: How do I remove the throttle to replace the cable

unscrew the top of the carburator and see if the spring is compressed when turning the throttle. If this has been done, you can reattach if not broken, if so replace cable. You might check that the throttle was replaced into the carburator the proper way, it can be 180 degrees out.

Posted on Jul 04, 2009

Ad

tombones

  • 3567 Answers

SOURCE: 1981 Yamaha MX upper replacement throttle cable.

Yes, take the cap off the carb and disconnect the cable then do the oil pump cable. The connector tube should then come apart for upper cable replacement. Please rate my answer. Thanks.

ae339d6.gif

Posted on Feb 19, 2010

Ambari

  • 901 Answers

SOURCE: 2009 Yamaha Raider S. Removing right side painted

Slightly lift the cover up & remove

Posted on Apr 03, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2015 Yamaha Raider S quit running while riding


Hi, Mike and the usual suspects are:
1. Severely discharged or a damaged battery must have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead-acid batteries.
2. Faulty alternator/generator and or voltage regulator.
3. Loose or corroded battery terminals and or cables especially the "NEGATIVE" cable, look for loose, corroded, or broken connectors inside the cable harness at "BOTH" ends.
4. Faulty main circuit breaker or ignition switch, check for loose connections and continuity.
5. Faulty system relay or ignition relay, check for continuity.
6. Faulty ignition coil, ignition/electronic module.
7. Faulty CKP, CPS, CMP, MAP, TPS, or BAS sensor, corroded, loose or broken wire connector pins/sockets.
8. Throttle cables and or idle speed improperly adjusted hot idle speed should be 950 RPM to 1000 RPM.
9. Faulty neutral, side stand or clutch lever safety switch.
10. Fuel tank empty
11. Fuel tank contaminated with ethanol sludge.
12. Water or dirt in the fuel system, or clogged filter.
13. Quick disconnect check ball stuck.
14. Restricted, blocked or kinked fuel line.
15. Faulty fuel pump.
16. Faulty pressure regulator.
17. Faulty or clogged fuel injectors.
18. Lean angle switch is faulty or needs adjustment.
19. Catastrophic engine failure, perform a compression test.
For more information about your issue and valuable "FREE" downloads that you need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.mybikeforums.com/forums/showthread.php?t=25779
https://www.quora.com/Why-does-my-bike-turns-off-while-riding
Yamaha XV19SW Service Manual
https://www.partsfish.com/page/oem-parts-for-yamaha
YAMAHA XV1900A Owner Manual

Sep 03, 2018 | 2015 Yamaha Raider S

1 Answer

2009 Yamaha Raider will not idle


Hi, Corey you need to make sure you have no intake leaks by spraying some Brake Kleen, Contact Cleaner, Starting Fluid etc. around the intake manifold and seals, if the RPM's go up or down significantly then you have a leak that needs to be fixed before you can continue with the carburetor adjustment.
The engine should be at operating temperature with the choke off to set the idle between 950-1050 rpm. Turn the idle skrew clockwise to increase the idle speed and counterclockwise to decrease the idle speed. If you have access to your air-fuel mixture skrew you may turn it as well, if not there is a video below on how to gain access, make sure you start with clean or new spark plugs. Gently turn the air-fuel mixture skrew clockwise until it starts to bottom out "STOP" do not over tighten as it will damage the taper on the end, now back the skrew out 1-1/2 full turns to establish a starting point start the engine and check the idle rpm's and turn the idle skrew accordingly for 950-1050 rpm if necessary, turn the air-fuel mixture skrew 1/4 turn at a time and let the engine settle for about 10 seconds, turn the skrew clockwise for a leaner mixture and counterclockwise for a richer mixture, you are seeking the highest rpm your air-fuel mixture skrew can acquire without going past 3 full turns from the bottom then resetting the idle skrew back down to 950-1050 rpm If you can not detect any rpm change and can not stall the engine by turning the air-fuel mixture skrew all the way in then your pilot/low-speed jet is too big and needs to be replaced with the next size smaller. Final adjustment should be made with a clean air filter mounted to the carburetor.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.mybikeforums.com/forums/showthread.php?t=14820
2008 Star Raider sans IAC Manually adjusted idle
Yamaha XV19SW Service Manual
https://www.partsfish.com/page/oem-parts-for-yamaha
YAMAHA XV1900A Owner Manual

Jul 31, 2018 | 2009 Yamaha Raider

1 Answer

2010 Yamaha V Star 950 on-load to off-load the bike jerks


Hi, Gregory, you throttle up and back off and somewhere in between the bike starts jerking. 99.9% of the time this is due to loose or worn out chain and sprockets or belt and pulleys.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
07 1300T Jerky Star Motorcycle Forums Star Raider Max Star Road Star Forum
https://www.reddit.com/r/motorcycles/comments/1uzmo4/vstar_950_xvs95_has_weird_skipping_problem
2009 2012 Yamaha XVS950 Star Service Repair Manual DOWNLOAD Download... $15
https://www.partsfish.com/page/oem-parts-for-yamaha
2010 Yamaha XVS950 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Jun 04, 2018 | 2010 Yamaha V Star 950

1 Answer

2008 Yamaha Raider S quits running when hot


Hi, Donald and the usual suspects are:
1. Severely discharged or a damaged battery must have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead-acid batteries.
2. Faulty alternator/generator and or voltage regulator.
3. Loose or corroded battery terminals and or cables especially the "NEGATIVE" cable, look for loose, corroded, or broken connectors inside the cable harness at "BOTH" ends.
4. Faulty main circuit breaker or ignition switch, check for loose connections and continuity.
5. Faulty system relay or ignition relay, check for continuity.
6. Faulty ignition coil, ignition/electronic module.
7. Faulty CKP, CPS, CMP, MAP, TPS, or BAS sensor, corroded, loose or broken wire connector pins/sockets.
8. Throttle cables and or idle speed improperly adjusted hot idle speed should be 950 RPM to 1000 RPM.
9. Faulty neutral, side stand or clutch lever safety switch.
10. Fuel tank empty
11. Fuel tank contaminated with ethanol sludge.
12. Water or dirt in the fuel system, or clogged filter.
13. Quick disconnect check ball stuck.
14. Restricted, blocked or kinked fuel line.
15. Faulty fuel pump.
16. Faulty pressure regulator.
17. Faulty or clogged fuel injectors.
18. Lean angle switch is faulty or needs adjustment.
19. Catastrophic engine failure, perform a compression test.
For more information about your issue and valuable "FREE" downloads that you need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://groups.google.com/forum/#!topic/alt.scooter/jwRUQITS9lA Throttle Position Sensor Issues Are you Experiencing Poor Idle Mileage or...
Yamaha Raider 1900 2008 2009 Workshop Service Manual Download Manuals... $15
https://www.partsfish.com/page/oem-parts-for-yamaha
https://dd5394a0b8ca8e97ba29-abf76f3d91a2125517d6c7c409f095c7.ssl.cf1.rackcdn.com/content/common/manuals/2008/LIT-11626-21-26_Raiders_1585.pdf free owners manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

May 03, 2018 | 2008 Yamaha Raider S

1 Answer

08 yamaha raider wont stay running


It most definitely is NOT the carbs since the 1900cc Raider is fuel injected.

Jul 22, 2013 | 2008 Yamaha Raider S

1 Answer

2010 Yamaha Raider Motorcycle wont start


Hi, Anonymous and the usual suspects are:
1. Fuel tank empty.
2. Fuel supply valve/petcock turned off.
3. Fouled spark plugs.
4. Engine flooded as a result of overuse of the enricher.
5. Vacuum hose to the fuel supply valve/petcock disconnected, broken, cracked, or pinched.
6. Fuel valve/petcock or filter clogged.
7. Fuel line to the carburetor or throttle body pinched or kinked.
8. Carburetor float stuck.
9. Fuel injectors clogged.
10. Severely discharged or damaged battery you need 12.5 volts or better and be able to pass a load test if necessary.
11. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
12. Loose or corroded wire connection at the coil, battery or plug between ignition sensor and CDI box.
Spark plug cables in bad condition and shorting check for leakage in the dark, cable connections loose, or connected to the wrong cylinders.
13. Ignition timing incorrect due to a faulty MAP, CKP, O2, TPS, sensors.
14. Faulty neutral, clutch lever, or kickstand safety switch.
15. Faulty fuel pump or fuse or relay.
16. Faulty CDI box.
17. A stuck bent or burnt valve.
18. Tip over sensor needs a reset.
19. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
Can get the bike to start
What to do When Your Motorcycle Won Start
Yamaha XV19SW Service Manual
OEM parts for Yamaha
Yamaha ROADLINER XV19SW Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Jan 28, 2013 | 2010 Yamaha Star Raider

1 Answer

2008 yamaha raider step by step air filter replacement


Hi, Anonymous for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere zero $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
Yamaha XV1900 Raider Air Filter Replacement Air Filters
How To Remove The Gas Tank Change The Air Filter And Change The Spark...
Roadliner Gas Tank Removal
Yamaha XV1700PCRC Service Manual
OEM parts for Yamaha
Yamaha XV1700PCR Road Star Warrior Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


Oct 08, 2012 | 2008 Yamaha Raider

1 Answer

Replace throttle cable 1986 yamaha virago


Hi, Anonymous for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
ViragoTechForum com
Yamaha 535 Throttle Cable Replacement
Yamaha XV535 Owners Workshop Manual
OEM parts for Yamaha
YAMAHA XV535 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


Apr 17, 2012 | Yamaha Motorcycles

1 Answer

Yamaha raider wiring diagram


Hi, Anonymous for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Yamaha raider wiring diagram Google Search
Yamaha Motorcycle Wiring Diagrams
Yamaha XV19SW Service Manual
OEM parts for Yamaha
YAMAHA XV1900A Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Feb 16, 2012 | 2011 Yamaha Raider S

Not finding what you are looking for?
2008 Yamaha Raider Logo

Related Topics:

428 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

gbob59

Level 3 Expert

3063 Answers

Neil Lancaster
Neil Lancaster

Level 1 Expert

14 Answers

randymanfive

Level 3 Expert

501 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...