Question about 2005 Kymco Zing 125

1 Answer

Kymco zing what is the valve clearance - 2005 Kymco Zing 125

Posted by Htaz100 on

Ad

1 Answer

Lars Silen

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

I found an owner's instruction manual on the net in Spanish that says:
0,05 mm - 0,1 mm

This means that the valve clearance is 0.05 to 0.1 mm. A slightly tight adjustment using a 0.1 feeler gage should be ok and the real clearance would then probably be ca. 0.08 mm.

Posted on Oct 08, 2012

Ad

5 Related Answers

Anonymous

  • 632 Answers

SOURCE: Where can i find a r/h switchgear for a kymco zing

There are many sites you can take a look at like
http://www.bitzforbikes.co.uk/Kymco/Zing_125/98_-_03 and http://www.wemoto.com/bikes/Kymco/Zing_125_Custom_RF25/97-06/

Posted on Jul 09, 2010

Ad

tombones

  • 3567 Answers

SOURCE: No power on my Kymco Zing 125

Usually the main fuse is located within 12" of the battery. If the fuse is okay then check that the battery has the red wire on the positive terminal and that connections are tight. Check the wiring harness for loose connections. If your bike has a kickstand safety switch then be sure the kickstand is up when starting. Be sure the kill switch is in the correct position and that you have gas in the tank and the fuel is turned on.

Posted on Mar 14, 2009

Anonymous

  • 4 Answers

SOURCE: Kymco Zing starting problem

the problem may be that there is not anuf power in the battery or the starter motor is on its way out

Posted on Oct 16, 2009

Edward Hurst

  • 77 Answers

SOURCE: Replace regulator/rectifier with a different brand?

Not always necessary to change the regulator/rectifier. Check all connections to make sure they are clean, use a good contact cleaner and finish off with dielectric grease on your electrical connections.
When some bikes get a few years on them the connections get dirty. Check to see if there are any burned or discolored wires anywhere around the regulator. The FIX on some bikes is to cut the connector completely out and solder the wires together and either seal them with heat shrink of a good electrical tape. Loose or bad connections get hot. As long as the regulator and rectifier are working there is no need to replace them if the connections are good.
Ride Safely, Ed

Posted on Apr 09, 2010

protuha

Goran Andric

  • 208 Answers

SOURCE: Hi there What type of oil

For your bike you should use 15w 40 oil. Buy some better known mark oil.

Posted on Nov 30, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kymco zing 125


Change the bulbs on that side

Jan 29, 2014 | Kymco Zing 125 Motorcycles

2 Answers

What is the valve clearence for kymco spike 125


Valve clearance for Kymco Spike 125 ( cold )
Intake - 0.12 mm
Exhaust - 0.12 mm
If you have any doubts don't forget to post me a reply.If you are satisfied please rate my solution.

Jun 04, 2011 | 2006 Kymco Spike

1 Answer

Where can i obtain fork seals for a kymco zing 125 or other spares


01159 596969 And ask for james Lisk. It's a charity in Nottingham called Wheelbase that sell's spare parts and specializes in Chinese and Taiwanese bikes

Oct 22, 2010 | 2005 Kymco Zing 125

1 Answer

Replace regulator/rectifier with a different brand?


Not always necessary to change the regulator/rectifier. Check all connections to make sure they are clean, use a good contact cleaner and finish off with dielectric grease on your electrical connections.
When some bikes get a few years on them the connections get dirty. Check to see if there are any burned or discolored wires anywhere around the regulator. The FIX on some bikes is to cut the connector completely out and solder the wires together and either seal them with heat shrink of a good electrical tape. Loose or bad connections get hot. As long as the regulator and rectifier are working there is no need to replace them if the connections are good.
Ride Safely, Ed

Apr 08, 2010 | 2005 Kymco Zing 125

1 Answer

Kymco Zing starting problem


the problem may be that there is not anuf power in the battery or the starter motor is on its way out

Jan 28, 2009 | 2005 Kymco Zing 125

Not finding what you are looking for?
2005 Kymco Zing 125 Logo

Related Topics:

462 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kymco Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

6571 Answers

Are you a Kymco Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...