Question about 2001 Yamaha YZF-R6

1 Answer

All the fuel lines and vacum hose have bee remove. I need a SCAMMATIC SHOWING WHAT HOOKS UP TO WHAT

Posted by jimbo408sj on

Ad

1 Answer

John Fourteen Six

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,418 Answers

all the fuel lines and - mcneb_63.jpgTry this see if it helps.

Posted on Sep 19, 2011

  • John Fourteen Six Sep 19, 2011

    That did not work, so go to > www.carlsalter.com < look for the free motorcycle manuals. There is a parts catalog for your bike there. That will break down for you how stuff fits together.

×

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How To Drain Fuel Tank On 2005 Jeep Liberty Gas Tank


here is the Cherokee page.
read chapter, 14, page 19 on..
shows all way there, and is not easy.
why do this.
is pressure low
pump dead
is there 12vdc to pump cranking, (no? then dont do this)

http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

i have the KJ pages here. (line # messed up)
Two different procedures may be used to drain fuel
tank: through the fuel fill fitting on tank, or using a
scan tool.
The quickest draining procedure involves removing
the rubber fuel fill hose (7) (Fig. 25) from fuel tank
fitting.
As an alternative procedure, the electric fuel pump
may be activated allowing tank to be drained at fuel
rail connection. Refer to DRB scan tool for fuel pump
activation procedures. Before disconnecting fuel line
at fuel rail, release fuel pressure. Refer to the Fuel
System Pressure Release Procedure for procedures.
Attach end of special test hose tool number 6541,
6539, 6631 or 6923 at fuel rail disconnection (tool
number will depend on model and/or engine application).
Position opposite end of this hose tool to an
approved gasoline draining station. Activate fuel
pump and drain tank until empty.
If electric fuel pump is not operating, fuel must be
drained through fuel fill fitting at tank. Refer to following
procedures.
(1) Release fuel system pressure.
(2) Raise vehicle.
(3) If equipped, remove fuel tank skid plate.
(4) Thoroughly clean area around fuel fill fitting
(6) (Fig. 26) and rubber fuel fill hose (1) at side of
fuel tank. After cleaning, loosen fuel fill hose clamp
(2) at tank.
(5) Before removing rubber hose (1) (Fig. 26) from
fitting, note hose orientation while referring to marks
(3) and (4).
6) Disconnect rubber fuel fill hose at fuel tank fitting
(2) (Fig. 27). Using an approved gas holding
tank, drain fuel tank through this fitting.
Tank Removal
(1) If equipped, remove fuel tank skid plate and
tow hooks. Certain equipment packages will also
require removal of the trailer hitch. Refer to Tow
Hooks, Trailer Hitch or Skid Plate in 23, Body for
removal/installation procedures.
(2) Disconnect and separate fresh air tube (6) (Fig.
28) quick-connect fitting.
(3) Disconnect air tubes at front of NVLD pump
(9) (Fig. 28).
(4) Disconnect NVLD pump (9) (Fig. 28) electrical
connector.
(5) Disconnect fuel pump module electrical connector
jumper. This is located near front of fuel tank.
(6) Support tank with a hydraulic jack.
(7) Remove 4 fuel tank strap bolts (10) (Fig. 28) (2
at front of tank; 2 at rear of tank), and remove both
tank support straps.
(8) Carefully lower tank a few inches.
(9) Continue lowering tank while guiding remaining
hoses and lines through plastic isolator sleeve (3)
(Fig. 29).
(10) If fuel tank is to be replaced, remove NVLD
pump and fuel pump module from tank. Refer to
Fuel Pump Module Removal/Installation procedures.
end , tank out.

why not login to alldata.com and read
or buy the FSM,, and get all pages of chapter 14, end to end.

Oct 19, 2015 | 2005 Jeep Liberty

1 Answer

I've removed my tank and mixed the fuel and vacum


Try to start it hold two fingers above hoses one with most suction is vacuum or follow hoses may be hard but follow one of them to middle of car thats fuel or unhook other ends of hoses plug one into gas let other one hang freely you will see gas u no thats fuel line

Jun 06, 2011 | 1995 Triumph Trident 900

1 Answer

Where does the vacum hose under the batt go looks like it come's out of the top of the canister then not sure where it hooks up to


If you're talking about the charcoal cannister, that's probably the vent hose that let's air in during purge. It does not attach--it's just open on the end. Are there 2 other hoses on the cannister--one from the fuel tank and one that goes to the intake manifold? If yes, then you're good.

Dec 27, 2010 | 2000 Ford Contour

1 Answer

Need fuel and vacuum line info


there should only 2 lines from the fuel tap, one for fuel, and the other for vacume, the smaller diameter hose is the vacume, and the larger hose is fuel. fuel hose will go to carby, and the vacume hose to the carby inlet manifold.

May 23, 2010 | Yamaha MT-01 Motorcycles

2 Answers

Check engine light on fuel to lean what to look for


Generally this comes from a few things

an oxygen sensor for the vehicle is bad, a vaccum hose is bad or a unit in the vaccum system is bad.

Feb 11, 2010 | Hyundai Computers & Internet

1 Answer

1985 Yamaha xj700 Maxim- Carb. fuel lines


yes, the breather line hooks to the petcock on the line facing the back, the fuel line hooks to the larger one. the line from the breather is actually a vacume line that turns on the fuel, without it you will not get fuel out of the petcock unless it is in the prime position.

Jul 04, 2009 | 1985 Yamaha XJ 700 X Maxim

2 Answers

Engine hard to start after setting over night. once started works well . why? 1997 cad eldorado


HI,OK IF THE CAR CRANK FOR A LONE TIME AFTER SITTING YOUR ISSUE IS FUEL PRESURE (IE THE PRESURE REGLATOR) ON THE 4.6 NORHSTAR ITS UNDER THE PLASTIC ENGINE COVER SIMPLY REMOVE THE 4 10MM NUTS AND LOOK FOR THE REGULATOR,ITS THE SILVER ROUND THING (WHERE THE FUEL LINES ATTATCH TO THE FUEL RAIL,AND IT HAS A RUBBER VACUME HOSE ATTATCHED TO IT. PULL THE VACUME LINE AND IF FUEL COMES OUT OF THE LINE OR IT SMELLS LIKE FUEL YOU REGULATOR HAS FAILED.

Jun 17, 2009 | 1997 Cadillac Eldorado

1 Answer

Fuel pressure regulator had no vacuum line connected


another engineers wet dream. think of it this way . what is normally in the intake when the engine is running.. answer vacume, hence the regulator gets its vacume without a hose connected to it as its already in a full time vacume chamber.no hose required . ps be carefull to seat the regulator and o rings securely into the housing befor you reattach the secureing metal clip.
good luck chris

Mar 22, 2009 | 1997 Chevrolet Suburban

1 Answer

Engine will turn over but will not continue to run


the fuel filter is in the tank on top of petcock that bike has a vacum operated petcock(fuelvalve)if the vacum hose is bad no fuel flow check the back of the fuel valve for a small hose that goes to the manifold make sure it is good put vacum on the hose wile hooked to the fuel valve and make sure that gas runs out of the hose give me a rate please hope this helps

Dec 13, 2008 | 1997 Honda VF 750 C Magna

1 Answer

1993 Dodge Caravan


I had exactly the same problem after I changed the fuel filter. Tried new clamps and tightening them etc. Nothing worked until I purchased a foot long hose from a auto store for couple bucks and replaced the both ends with the new hoses. Old hose hardens over time and it doesn't seal well after it has been reused.

Jun 19, 2008 | 1993 Dodge Caravan

Not finding what you are looking for?
2001 Yamaha YZF-R6 Logo

Related Topics:

137 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

gbob59

Level 3 Expert

3063 Answers

Neil Lancaster
Neil Lancaster

Level 1 Expert

14 Answers

randymanfive

Level 3 Expert

501 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...